Setting this attribute to any of the above values will
initiate a test on the specific port if the operation is
legal. If the operation is not legal, the mux will ignore
the operation.
testPerTS(31) - when this test is selected, the selection of tests
for each TS is done via the prtExPh1MlTsTest object.
If a test time out is needed, the test will be set with a
default timeout of 2 minutes until the user will set the
parameter 'prtSTstDuration' to the required time out.
If no time out is needed , the test will be set with infinite
timeout until the user will set the parameter
'prtSTstDuration' to the required time out.
Parsed from file Rad0485.MIB.txt
Company: None
Module: RAD-MIB
Setting this attribute to any of the above values will
initiate a test on the specific port if the operation is
legal. If the operation is not legal, the mux will ignore
the operation.
testPerTS(31) - when this test is selected, the selection of tests
for each TS is done via the prtExPh1MlTsTest object.
If a test time out is needed, the test will be set with a
default timeout of 2 minutes until the user will set the
parameter 'prtSTstDuration' to the required time out.
If no time out is needed , the test will be set with infinite
timeout until the user will set the parameter
'prtSTstDuration' to the required time out.
Parsed from file RAD-MIB.mib
Module: RAD-MIB
Vendor: Rad Data Communications Ltd.
Module: DACS-MIB
[Automatically extracted from oidview.com]
prtSTstCmd OBJECT-TYPE SYNTAX INTEGER { none (1), localLoop (2), remoteLoop (3), locAndRemMainLoops (4), remoteAnalogLoop (5), remoteDigitalLoop (6), remLoopOnExtUnit (7), bert (8), toneInjection (9), dlciLocalLoop (10), allDlciLocalLoop (11), dlciRemoteLoop (12), allDlciRemoteLoop (13), extInitLocalLoop (14), bertAndRemLoopOnRemUnit (15), remLoopOnRemUnit (16), block (17), backwardToneInject (18), llb (19), rlb (20), ft1Enable (21), lbbd (22), lb1 (23), lb2 (24), llbOnRemUnit (25), bertOnRemUnit (26), bertOnRemAndLlbOnRemUnit (27), localAndBertOnRemUnit(28), localLoopOnRemUnit (29), localBert (30), testPerTS (31) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out." ::= { prtSInstEntry 10}
prtSTstCmd OBJECT-TYPE SYNTAX INTEGER { none (1), localLoop (2), remoteLoop (3), locAndRemMainLoops (4), remoteAnalogLoop (5), remoteDigitalLoop (6), remLoopOnExtUnit (7), bert (8), toneInjection (9), dlciLocalLoop (10), allDlciLocalLoop (11), dlciRemoteLoop (12), allDlciRemoteLoop (13), extInitLocalLoop (14), bertAndRemLoopOnRemUnit (15), remLoopOnRemUnit (16), block (17), backwardToneInject (18), llb (19), rlb (20), ft1Enable (21), lbbd (22), lb1 (23), lb2 (24), llbOnRemUnit (25), bertOnRemUnit (26), bertOnRemAndLlbOnRemUnit (27), localAndBertOnRemUnit(28), localLoopOnRemUnit (29), localBert (30), testPerTS (31) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out." ::= { prtSInstEntry 10}
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.1.4.1.1.1.1 | prtSInstSltIdx | 0 | 0 | This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..i… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.2 | prtSInstPrtIdx | 0 | 0 | This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the … |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.3 | prtSInstPrtType | 0 | 0 | This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other opt… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.4 | prtSInstIfIndex | 0 | 0 | This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.5 | prtSActiveStatus | 0 | 0 | This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) … |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.6 | prtSAlrStatus | 0 | 0 | Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one ac… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.7 | prtSMaskedAlrStat | 0 | 0 | Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when … |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.8 | prtSClearAlrCmd | 0 | 0 | Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.9 | prtSTestMask | 0 | 0 | This is a mask which indicates which tests from the 'prtSTstCmd' list are allowed for the requested port. If a specific test is a… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.11 | prtSTstDuration | 0 | 0 | This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operat… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.12 | prtSBertClrCmd | 0 | 0 | Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port. |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.13 | prtSBertTstRslt | 0 | 0 | This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is act… |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.14 | prtSInterfaceType | 0 | 0 | This attribute indicates a unique HW interface type of the selected port. |
| 1.3.6.1.4.1.164.3.1.4.1.1.1.15 | prtSParamStatus | 0 | 0 | This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported… |