rc3SysPerftimeBetweenPolls
View at oid-info.com
Time in seconds after which the polling will occur. A value of 0
means that this Ravlin will not poll. Default value is zero(0). The
minimum value can be set is 30 seconds and maximum is 600 seconds.
Parsed from file Ravlin.mib.txt
Company: None
Module: RCV3
Time in seconds after which the polling will occur. A value of 0
means that this Ravlin will not poll. Default value is zero(0). The
minimum value can be set is 30 seconds and maximum is 600 seconds.
Parsed from file RCV3.mib
Module: RCV3
Vendor: Red Creek Communications, Inc.
Module: RCV3
[Automatically extracted from oidview.com]
rc3SysPerfTimeBetweenPolls OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Time in seconds after which the polling will occur. A value of 0 means that this Ravlin will not poll. Default value is zero(0). The minimum value can be set is 30 seconds and maximum is 600 seconds." ::= { rc3Control 10 }
rc3SysPerfTimeBetweenPolls OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Time in seconds after which the polling will occur. A value of 0 means that this Ravlin will not poll. Default value is zero(0). The minimum value can be set is 30 seconds and maximum is 600 seconds." ::= { rc3Control 10 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1958.1.1.8.3.10.0 | rc3SysPerfTimeBetweenPolls | 0 | 0 | rc3SysPerftimeBetweenPolls |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1958.1.1.8.3.1 | rc3Reset | 1 | 1 | Action object to do the following: warmstart - Reboots the device. Firmware and configuration information is maintained. clearal… |
| 1.3.6.1.4.1.1958.1.1.8.3.2 | rc3ArpCacheCleanupInterval | 1 | 1 | The duration in minutes to cleanup ARP cache. |
| 1.3.6.1.4.1.1958.1.1.8.3.3 | rc3Password | 1 | 1 | Object used to set new password for the box. For SNMP set operations the password is encrypted. The key for encrypt/Decrypt is g… |
| 1.3.6.1.4.1.1958.1.1.8.3.4 | rc3OperationalMode | 1 | 1 | The desired state of the Ravlin. For the passall and vpnready modes, the device will act as either a router or a bridge dependi… |
| 1.3.6.1.4.1.1958.1.1.8.3.5 | rc3InactiveClientTimeout | 1 | 1 | The duration in minutes to tear down the SA between the RavSoft client and Ravlin server. |
| 1.3.6.1.4.1.1958.1.1.8.3.6 | rc3DHCPServerIP | 1 | 1 | IP Address of the DHCP server. This address can ONLY configured manually by SNMP. |
| 1.3.6.1.4.1.1958.1.1.8.3.7 | rc3DHCPRequest | 1 | 1 | This is Bit Masked Object. Zero or more bits can be set or cleared. Bit 0 - Enable/Disable DHCP on the Local Port Bit 1 - Enable/… |
| 1.3.6.1.4.1.1958.1.1.8.3.8 | rc3PasswordFips | 1 | 1 | Available for release 3.30 and up. Object used to set new password for the box. Refer to the textual convention of PbeShaEncrypt… |
| 1.3.6.1.4.1.1958.1.1.8.3.9 | rc3DHCPRelayIpAddr | 1 | 1 | IP Address to be used for DHCP Relay. This is used when the Ravlin unit redeives a DHCP request from the Ravsoft client. |
| 1.3.6.1.4.1.1958.1.1.8.3.11 | rc3SysPerfTimeBetweenReports | 1 | 1 | rc3SysPerftimeBetweenReports |
| 1.3.6.1.4.1.1958.1.1.8.3.12 | rc3SysPerfTrapThreshold | 1 | 1 | rc3SysPerftrapThreshold |
| 1.3.6.1.4.1.1958.1.1.8.3.13 | rc3DHCPBroadcastIntf | 1 | 1 | Indentify the interface to broadcast DHCP requests. When the DHCP server IP Address is not a broadcast address, then SNMP agent … |
| 1.3.6.1.4.1.1958.1.1.8.3.14 | rc3StateLessDHCP | 1 | 1 | Enables a head end device not to keep state information for DHCP records, used in DHCP relay. This will allow head end to be in c… |