The trap sender table (0 to 25 entries). This
table lists the addresses of Network Management
Stations and the Source Address that should receive
trap messages from this entity when an exception
condition occurs.
Parsed from file rapid_city-accelar.mib.txt
Company: rapidcity
Module: RAPID-CITY
rcSysTrapSenderTable OBJECT-TYPE SYNTAX SEQUENCE OF RcSysTrapSenderEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The trap sender table (0 to 25 entries). This table lists the addresses of Network Management Stations and the Source Address that should receive trap messages from this entity when an exception condition occurs." ::= { rcSystem 62 }
Vendor: Avaya
Module: RAPID-CITY (RAPID-CITY.mib)
Type: TABLE
Access: not-accessible
Syntax: SEQUENCE OF
Automatically extracted from www.mibdepot.com
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2272.1.1.62.1 | rcSysTrapSenderEntry | 2 | 2 | A trap sender table entry. |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.2272.1.1.12 | rcSysLastStatisticsReset | 1 | 1 | Last management initiated statistics reset since sysUpTime. |
| 1.3.6.1.4.1.2272.1.1.13 | rcSysBufferUtil | 1 | 1 | Buffer utilization as a percentage of the total amount of buffer space in the system. A high value indicates congestion. |
| 1.3.6.1.4.1.2272.1.1.14 | rcSysBufferUtilPeak | 1 | 1 | The largest buffer utilization since sysUpTime |
| 1.3.6.1.4.1.2272.1.1.15 | rcSysBufferUtilPeakTime | 1 | 1 | Timestamp for rcSysPeakBandwidth |
| 1.3.6.1.4.1.2272.1.1.16 | rcSysNVRamSize | 1 | 1 | Total Non-volatile RAM in Kbytes |
| 1.3.6.1.4.1.2272.1.1.17 | rcSysNVRamUsed | 1 | 1 | Non-volatile RAM in use in Kbytes |
| 1.3.6.1.4.1.2272.1.1.18 | rcSysLastSaveToNVRam | 1 | 1 | SysUpTime of the last time when NVRAM was written to. This could be a save of the system configuration or via a file transfer of… |
| 1.3.6.1.4.1.2272.1.1.19 | rcSysLastSaveToStandbyNVRam | 1 | 1 | SysUpTime of the last time when the standby NVRAM (on the back-up CPU board) was written to. |
| 1.3.6.1.4.1.2272.1.1.20 | rcSysCpuUtil | 1 | 1 | Percentage of CPU utilization |
| 1.3.6.1.4.1.2272.1.1.21 | rcSysSwitchFabricUtil | 1 | 1 | Percentage of Switching Fabric utilization |
| 1.3.6.1.4.1.2272.1.1.22 | rcSysRmonMemSize | 1 | 1 | Amount of RAM in bytes to allocate for RMON to use when rcSysRmonEnable is TRUE. |
| 1.3.6.1.4.1.2272.1.1.23 | rcSysRmonEnable | 1 | 1 | Control whether the RMON feature should be enabled. To enable the RMON feature, set this variable to true. The RMON agent in the … |
| 1.3.6.1.4.1.2272.1.1.24 | rcSysRmonSaveConfig | 1 | 1 | Control whether RMON configuration information should be saved to NVRAM so RMON settings can be automatically reinstalled after a… |
| 1.3.6.1.4.1.2272.1.1.25 | rcSysRmonTrapOption | 1 | 1 | Used to indicate whether RMON traps should be sent to only the owner of the RMON alarm (i.e., the manager that created the alarm … |
| 1.3.6.1.4.1.2272.1.1.26 | rcSysSupportRouting | 1 | 1 | Used to indicate whether routing is supported in this product. |
| 1.3.6.1.4.1.2272.1.1.27 | rcSysSupportWebServer | 1 | 1 | Used to indicate whether WebServer is supported in this product. |
| 1.3.6.1.4.1.2272.1.1.28 | rcSysLastIpAddrChange | 1 | 1 | Last management initiated IP address change since sysUpTime. Any addition or deletion of an IP address to a single routable port… |
| 1.3.6.1.4.1.2272.1.1.29 | rcSysCommReadWriteLayer3 | 1 | 1 | When an SNMP message is received by this entity, the community string in the message is compared with this string third. If it m… |
| 1.3.6.1.4.1.2272.1.1.30 | rcSysCommReadWriteLayer2 | 1 | 1 | When an SNMP message is received by this entity, the community string in the message is compared with this string fourth. If it … |
| 1.3.6.1.4.1.2272.1.1.31 | rcSysAccessPolicyEnable | 1 | 1 | Used to configure the system access policy feature. if 'true', the rcSysAccessPolicyTable is examined to determine which packets … |
| 1.3.6.1.4.1.2272.1.1.32 | rcSysDefaultRuntimeConfigFileName | 1 | 1 | default config. |
| 1.3.6.1.4.1.2272.1.1.33 | rcSysDefaultBootConfigFileName | 1 | 1 | default boot config. |
| 1.3.6.1.4.1.2272.1.1.34 | rcSysConfigFileName | 1 | 1 | File name used in conjunction with rcSysAction. If rcSysAction is set to 'saveRuntimeConfig' or 'saveRuntimeConfigToSlave' then t… |
| 1.3.6.1.4.1.2272.1.1.35 | rcSysLastRunTimeConfigSave | 1 | 1 | SysUpTime of the last time when the run time configuration was written to. |
| 1.3.6.1.4.1.2272.1.1.36 | rcSysLastRunTimeConfigSaveToSlave | 1 | 1 | SysUpTime of the last time when the run time configuration was written to slave NVRAM. |
| 1.3.6.1.4.1.2272.1.1.37 | rcSysLastBootConfigSave | 1 | 1 | SysUpTime of the last time when the boot configuration was written to. |
| 1.3.6.1.4.1.2272.1.1.38 | rcSysLastBootConfigSaveOnSlave | 1 | 1 | SysUpTime of the last time when the boot configuration was written on the slave NVRAM. |
| 1.3.6.1.4.1.2272.1.1.39 | rcSysRmonUtilizationMethod | 1 | 1 | Used to control whether RMON should use a half-duplex or full-duplex formula to calculate port utilization. When set to 'halfDupl… |
| 1.3.6.1.4.1.2272.1.1.40 | rcSysCommReadWriteLayer1 | 1 | 1 | read-write L1 access |
| 1.3.6.1.4.1.2272.1.1.41 | rcSysOtherBufferUtil | 1 | 1 | bw currently consumed |
| 1.3.6.1.4.1.2272.1.1.42 | rcSysOtherBufferUtilPeak | 1 | 1 | peak bw since reset |
| 1.3.6.1.4.1.2272.1.1.43 | rcSysOtherBufferUtilPeakTime | 1 | 1 | timestamp for rcSysPeakBw |
| 1.3.6.1.4.1.2272.1.1.44 | rcSysOtherCpuUtil | 1 | 1 | % cpu utilization |
| 1.3.6.1.4.1.2272.1.1.45 | rcSysOtherSwitchFabricUtil | 1 | 1 | % switch fabric util |
| 1.3.6.1.4.1.2272.1.1.46 | rcSysDramSize | 1 | 1 | Dram size in mega-bytes |
| 1.3.6.1.4.1.2272.1.1.47 | rcSysDramUsed | 1 | 1 | Dram used in percentage |
| 1.3.6.1.4.1.2272.1.1.48 | rcSysDramFree | 1 | 1 | Dram free size in kilo-bytes |
| 1.3.6.1.4.1.2272.1.1.49 | rcSysDramMaxBlockFree | 1 | 1 | Dram max block free size in kilo-bytes |
| 1.3.6.1.4.1.2272.1.1.51 | rcSysVirtualIpAddr | 1 | 1 | Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP addres… |
| 1.3.6.1.4.1.2272.1.1.52 | rcSysVirtualNetMask | 1 | 1 | Net mask of the management virtual Ip address |
| 1.3.6.1.4.1.2272.1.1.53 | rcSysReadWriteLevel | 1 | 1 | The status of the read/write level |
| 1.3.6.1.4.1.2272.1.1.55 | rcSysMTUSize | 1 | 1 | This is the maximum transmission size of frames that all the ports on the chassis support. |
| 1.3.6.1.4.1.2272.1.1.56 | rcSysClockSyncTime | 1 | 1 | Time interval at which RTC and system clocks are synchronized. |
| 1.3.6.1.4.1.2272.1.1.57 | rcSysForceTrapSender | 1 | 1 | This is a flag that if user wants to configured CLIP (Circuit Less IP) as trap originator. |
| 1.3.6.1.4.1.2272.1.1.58 | rcSysMrouteStrLimit | 1 | 1 | enable or disable mroute stream limit in system. |
| 1.3.6.1.4.1.2272.1.1.60 | rcSysTrapRecvTable | 1 | 6 | The trap receiver table (0 to 25 entries). This table lists the addresses of Network Management Stations that should receive tra… |
| 1.3.6.1.4.1.2272.1.1.61 | rcSysAccessPolicyTable | 1 | 20 | Management access policy table. This table is used to permit or deny access to this device via the specified source Id. |
| 1.3.6.1.4.1.2272.1.1.63 | rcSysDnsServerListTableSize | 1 | 1 | Used to indicate the number of entries in the table. |
| 1.3.6.1.4.1.2272.1.1.64 | rcSysDnsServerListTable | 1 | 9 | DNS serever list table used to store the details of the DNS server configured. |
| 1.3.6.1.4.1.2272.1.1.65 | rcSysDnsHostTable | 1 | 7 | DNS Host table. |
| 1.3.6.1.4.1.2272.1.1.66 | rcSysMsgLogFrequency | 1 | 1 | Used to specify the maximum frequency/count of the occurence of the Log Message. |
| 1.3.6.1.4.1.2272.1.1.67 | rcSysMsgLogText | 1 | 1 | A textual string containing the first four characters of the Log Message. |
| 1.3.6.1.4.1.2272.1.1.68 | rcSysForceIpHdrSender | 1 | 1 | Flag to decide if IP header source address will be matched with SNMP header sender networks. |
| 1.3.6.1.4.1.2272.1.1.69 | rcSysVlanMaxId | 1 | 1 | The maximum vlan Id that supported |
| 1.3.6.1.4.1.2272.1.1.70 | rcSysDnsDomainName | 1 | 1 | Default domain used for querying the DNS Server. |
| 1.3.6.1.4.1.2272.1.1.71 | rcSysDnsServerListIpAddr | 1 | 1 | DNS server's IP address |
| 1.3.6.1.4.1.2272.1.1.72 | rcSysDnsRequestType | 1 | 1 | DNS Type: Whether it was Dns Request or a Response |
| 1.3.6.1.4.1.2272.1.1.73 | rcSysSpanningTreeOperMode | 1 | 1 | This object indicates the current spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older … |
| 1.3.6.1.4.1.2272.1.1.74 | rcSysSpanningTreeAdminMode | 1 | 1 | This object indicates the desired spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older … |
| 1.3.6.1.4.1.2272.1.1.75 | rcSysAutoRecoverDelay | 1 | 1 | Time interval in seconds after which auto-recovery runs on ports to clear action taken by cp-limit, link flap or loop detect |
| 1.3.6.1.4.1.2272.1.1.76 | rcSysMacFlapLimitTime | 1 | 1 | Time limit in milliseconds for MAC flapping for loop-detect feature |
| 1.3.6.1.4.1.2272.1.1.77 | rcSysMacFlapLimitCount | 1 | 1 | Number of times mac flapping can happen for loop-detect feature |
| 1.3.6.1.4.1.2272.1.1.78 | rcSysExtCplimitEnable | 1 | 1 | enable or disable extended CP-LIMIT in system. |
| 1.3.6.1.4.1.2272.1.1.79 | rcSysExtCplimitMinCongTime | 1 | 1 | Minimum time for which System octapid should be congested to trigger congestion algorithm for extended CP-LIMIT in mSecs |
| 1.3.6.1.4.1.2272.1.1.80 | rcSysExtCplimitMaxPorts | 1 | 1 | Maximum number of ports which need to be monitored for congestion in Extended CP-LIMIT |
| 1.3.6.1.4.1.2272.1.1.81 | rcSysExtCplimitPortCongTime | 1 | 1 | Minimum time for which ingress traffic utilization rate of a monitored port should stay more than the allowed limits in order to … |
| 1.3.6.1.4.1.2272.1.1.82 | rcSysExtCplimitTrapLevel | 1 | 1 | Indicates the trap level for extended CP-LIMIT |
| 1.3.6.1.4.1.2272.1.1.83 | rcSysExtCplimitSysOctapidCongested | 1 | 1 | Indicates whether system octapid congestion detected for extended cp-limit |
| 1.3.6.1.4.1.2272.1.1.84 | rcSysExtCplimitPortsMonitored | 1 | 1 | Indicates whether ports has been shutdown due to extended cp-limit |
| 1.3.6.1.4.1.2272.1.1.85 | rcSysExtCplimitPortsShutDown | 1 | 1 | Indicates whether ports has been shutdown due to extended Cp-limit |
| 1.3.6.1.4.1.2272.1.1.86 | rcSysActionL1 | 1 | 1 | Initiate a system action for layer1 user |
| 1.3.6.1.4.1.2272.1.1.87 | rcSysActionL2 | 1 | 1 | Initiate a system action for layer2 user |
| 1.3.6.1.4.1.2272.1.1.88 | rcSysActionL3 | 1 | 1 | Initiate a system action for layer2 user |
| 1.3.6.1.4.1.2272.1.1.89 | rcSysActionRwa | 1 | 1 | Initiate a system action. |
| 1.3.6.1.4.1.2272.1.1.90 | rcSysPowerUsage | 1 | 1 | The current power usage for the whole chassis. |
| 1.3.6.1.4.1.2272.1.1.91 | rcSysPowerAvailable | 1 | 1 | The current power available for the whole chassis. |
| 1.3.6.1.4.1.2272.1.1.92 | rcSysBpduStartMacAddress | 1 | 1 | Starting Multicast MAC address for BPDUs |
| 1.3.6.1.4.1.2272.1.1.93 | rcSysBpduMacAddressMask | 1 | 1 | BPDU MAC address Mask |
| 1.3.6.1.4.1.2272.1.1.94 | rcSysFrcMsgControlTable | 1 | 4 | Management Force-msg Control table. This table is used to specify the pattern for Force-msg Control |
| 1.3.6.1.4.1.2272.1.1.95 | rcSysAccPolSnmpGrpTable | 1 | 4 | SNMP group list for access policy |
| 1.3.6.1.4.1.2272.1.1.96 | rcSysVirtualIpv6Addr | 1 | 1 | The virtual ipv6 address that is owned, advertised, and registered by the master CPU only. Unlike the net management IP addres… |
| 1.3.6.1.4.1.2272.1.1.97 | rcSysVirtualIpv6PrefixLength | 1 | 1 | The length of the virtual ipv6 addr prefix (in bits). |
| 1.3.6.1.4.1.2272.1.1.98 | rcSysConfigMode | 1 | 1 | This is used in conjunction with rcSysAction inorder to decide the mode in which the config file is going to be saved in. |
| 1.3.6.1.4.1.2272.1.1.99 | rcSysExtendedPingBypass | 4 | 8 | None |
| 1.3.6.1.4.1.2272.1.1.100 | rcSysLicenseTrialDaysLeft | 1 | 1 | This indicates days left before License Trial Period will expire. |
| 1.3.6.1.4.1.2272.1.1.101 | rcSysSingleMgmtIpAddr | 1 | 1 | Single Managament IP Address |
| 1.3.6.1.4.1.2272.1.1.102 | rcSysCopHighCpuUtilThreshold | 1 | 1 | CopHighCpuUtilThreshold % |
| 1.3.6.1.4.1.2272.1.1.103 | rcSysCopHighCpuUtilLogTime | 1 | 1 | rcSysCopHighCpuUtilLogTime in secs |
| 1.3.6.1.4.1.2272.1.1.104 | rcSysConfigChangeFlag | 1 | 1 | Indicates whether the config file has been changed after loading of config |
| 1.3.6.1.4.1.2272.1.1.105 | rcSysBootUpgradeMode | 1 | 1 | To set the mode of bootupgrade |
| 1.3.6.1.4.1.2272.1.1.106 | rcSysBootUpgradeTime | 1 | 1 | To set time for bootupgrade |
| 1.3.6.1.4.1.2272.1.1.107 | rcSysBootUpgradeCsuMode | 1 | 1 | To set the mode of Csu for bootupgrade |
| 1.3.6.1.4.1.2272.1.1.108 | rcSysUpgradeStatus | 1 | 1 | To get the Upgrade status |
| 1.3.6.1.4.1.2272.1.1.109 | rcSysUpgradeCompleteStatus | 1 | 1 | To get the Upgrade status |
| 1.3.6.1.4.1.2272.1.1.110 | rcSysBootUpgradeConsistencyCheck | 1 | 1 | To enable or disable the consistency check in BootUpgrade |
| 1.3.6.1.4.1.2272.1.1.111 | rcSysAutoSaveConfigState | 1 | 1 | To enable or disable the autosaveconfig feature |
| 1.3.6.1.4.1.2272.1.1.112 | rcSysAutoSaveConfigFileName | 1 | 1 | The auto config file name in which the configurations have to be saved automatically. |
| ... | ||||