The number of receive FIFO overflows since the last reset.
If this condition persists, a lportCBRLineDataError trap is issued
indicating the receive FIFO overflow.
Parsed from file cascade.mib.txt
Company: None
Module: CASCADE-MIB
The number of receive FIFO overflows since the last reset.
If this condition persists, a lportCBRLineDataError trap is issued
indicating the receive FIFO overflow.
Parsed from file CASCADE-MIB.mib
Module: CASCADE-MIB
Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
lportRecFifoOverflowCnt OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of receive FIFO overflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the receive FIFO overflow." ::= { lportEntry 226 }
lportRecFifoOverflowCnt OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of receive FIFO overflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the receive FIFO overflow." ::= { lportEntry 226 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.277.1.5.1.1.176 | lportTrkProtState | 0 | 0 | The current operational state of the link trunk protocol on this link. |
| 1.3.6.1.4.1.277.1.5.1.1.177 | lportTrkTrafficMix | 0 | 0 | The types of traffic allowed over a Cascade trunk. |
| 1.3.6.1.4.1.277.1.5.1.1.178 | lportNumVC | 0 | 0 | The number of VCs going to or through a particular port. |
| 1.3.6.1.4.1.277.1.5.1.1.179 | lportTrkAdminCost | 0 | 0 | The administrative cost of the trunk. Used when routing circuits. Trunks with lower costs are preferred. Value ranges from 1 to 6… |
| 1.3.6.1.4.1.277.1.5.1.1.180 | lportPrivateNet | 0 | 0 | If non-zero, indicates the private network that the lport belongs to. If 0, the lport is publicly shared. |
| 1.3.6.1.4.1.277.1.5.1.1.181 | lportTrkStaticDelay | 0 | 0 | The measured round-trip delay of the trunk, in milliseconds. Measured when the trunk last became operational. |
| 1.3.6.1.4.1.277.1.5.1.1.182 | lportTrkDynamicDelay | 0 | 0 | The recently measured round-tip delay of the trunk. May vary from lportTrkStaticDelay due to congestion, or reprovisioning of the… |
| 1.3.6.1.4.1.277.1.5.1.1.183 | lportAtmDataRateQoS1 | 0 | 0 | An estimate of the logical port's data rate in bits per second reserved for QoS class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.184 | lportAtmDataRateQoS2 | 0 | 0 | An estimate of the logical port's data rate in bits per second reserved for QoS class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.185 | lportAtmDataRateQoS3 | 0 | 0 | An estimate of the logical port's data rate in bits per second reserved for QoS class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.186 | lportAtmDataRateQoS4 | 0 | 0 | An estimate of the logical port's data rate in bits per second reserved for QoS class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.187 | lportOutVAvailbwQoS1 | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.188 | lportOutVAvailbwQoS2 | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.189 | lportOutVAvailbwQoS3 | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.190 | lportOutVAvailbwQoS4 | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.191 | lportInVAvailbwQoS1 | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.192 | lportInVAvailbwQoS2 | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.193 | lportInVAvailbwQoS3 | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.194 | lportInVAvailbwQoS4 | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.195 | lportOutAllocbwQoS1 | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.196 | lportOutAllocbwQoS2 | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.197 | lportOutAllocbwQoS3 | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.198 | lportOutAllocbwQoS4 | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.199 | lportInAllocbwQoS1 | 0 | 0 | Current incoming allocated bandwidth for QoS Class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.200 | lportInAllocbwQoS2 | 0 | 0 | Current incoming allocated bandwidth for QoS Class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.201 | lportInAllocbwQoS3 | 0 | 0 | Current incoming allocated bandwidth for QoS Class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.202 | lportInAllocbwQoS4 | 0 | 0 | Current incoming allocated bandwidth for QoS Class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.203 | lportDynamicQoSbw | 0 | 0 | Bitmap defining which QoS Classes should have bandwidth allocated dynamically from lportDataRate instead of reserving a percentag… |
| 1.3.6.1.4.1.277.1.5.1.1.204 | lportSVCRetryTimer, lportSvcHoldDownTimer | 0 | 0 | The duration in seconds (1..255) the network is allowed to re-establish a SVC after network failure before clearing the SVC. A va… |
| 1.3.6.1.4.1.277.1.5.1.1.205 | lportAtmNetworkType, lportAtmConnectionType | 0 | 0 | Whether this lport is supporting a private or public network. |
| 1.3.6.1.4.1.277.1.5.1.1.206 | lportAtmRouteMetricQoS1 | 0 | 0 | Routing metric associated with QoS Class 1. |
| 1.3.6.1.4.1.277.1.5.1.1.207 | lportAtmRouteMetricQoS2 | 0 | 0 | Routing metric associated with QoS Class 2. |
| 1.3.6.1.4.1.277.1.5.1.1.208 | lportAtmRouteMetricQoS3 | 0 | 0 | Routing metric associated with QoS Class 3. |
| 1.3.6.1.4.1.277.1.5.1.1.209 | lportAtmRouteMetricQoS4 | 0 | 0 | Routing metric associated with QoS Class 4. |
| 1.3.6.1.4.1.277.1.5.1.1.210 | lportIlmiPollTimeout | 0 | 0 | The duration in seconds (1..255) the ILMI poll is generated by the network-side UME. A value of 0 set to default polling period o… |
| 1.3.6.1.4.1.277.1.5.1.1.211 | lportAtmProtocol | 0 | 0 | UNI protocol version for this port. |
| 1.3.6.1.4.1.277.1.5.1.1.212 | lportIlmiAdminStatus | 0 | 0 | Administrative state for ILMI function on this port. |
| 1.3.6.1.4.1.277.1.5.1.1.213 | lportIlmiOperStatus | 0 | 0 | Operational status for ILMI function on this port. |
| 1.3.6.1.4.1.277.1.5.1.1.214 | lportIlmiPollRetry | 0 | 0 | The number of retries of ILMI poll request will be generated when network-side UME detects loss of ILMI connectivity. A value of… |
| 1.3.6.1.4.1.277.1.5.1.1.215 | lportAtmVpiBits | 0 | 0 | Number of bits of VPI supported. |
| 1.3.6.1.4.1.277.1.5.1.1.216 | lportAtmVciBits | 0 | 0 | Number of bits of VCI supported. |
| 1.3.6.1.4.1.277.1.5.1.1.217 | lportAtmOamAlarmEnable | 0 | 0 | If disabled then OAM alarms are not generated for circuits that are down on this lport. |
| 1.3.6.1.4.1.277.1.5.1.1.218 | lportInVAvailbw | 0 | 0 | Currently available Incoming virtual bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.219 | lportbwUNIPolicy | 0 | 0 | The network policy towards requiring sufficient bandwidth at the UNI interface prior to allowing a circuit to be established. |
| 1.3.6.1.4.1.277.1.5.1.1.220 | lportStarvation | 0 | 0 | The CE/CBR card detected a starvation condition on this lport for an extended period |
| 1.3.6.1.4.1.277.1.5.1.1.221 | lportRecOverflow | 0 | 0 | The CE/CBR card detected a receive overflow condition on this lport for an extended period. |
| 1.3.6.1.4.1.277.1.5.1.1.222 | lportLossOfCellSequence | 0 | 0 | The CE/CBR card detected a LOS condition on this lport for an extended period. |
| 1.3.6.1.4.1.277.1.5.1.1.223 | lportLossOfStructurePointer | 0 | 0 | The structured CBR card detected a loss of structure pointer condition on this lport for an extended period. |
| 1.3.6.1.4.1.277.1.5.1.1.224 | lportCbrInsDummyCells | 0 | 0 | The number of dummy cells inserted due to cell loss on a constant bit rate (AAL1) interface. |
| 1.3.6.1.4.1.277.1.5.1.1.225 | lportRecFifoUnderflowCnt | 0 | 0 | The number of receive FIFO underflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued in… |
| 1.3.6.1.4.1.277.1.5.1.1.227 | lportCbrLossOfStructurePointerCnt | 0 | 0 | The object counts how often the structured CBR card detected a loss of the structure pointer since the last reset. |
| 1.3.6.1.4.1.277.1.5.1.1.228 | lportCbrLossOfCellSequenceCnt | 0 | 0 | The number of loss of cell sequence since the last reset. |
| 1.3.6.1.4.1.277.1.5.1.1.229 | lportShaperId | 0 | 0 | The shaper to be used for this ATM trunk interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card Values: 1..16 |
| 1.3.6.1.4.1.277.1.5.1.1.230 | lportIlmiPrefixScreenMode, lportDteIlmiPrefixScreenMode | 0 | 0 | The type of screening to apply against dynamic prefixes received from the peer ILMI entity at this DTE port. |
| 1.3.6.1.4.1.277.1.5.1.1.231 | lportSmdsPduViolTca | 0 | 0 | This object defines the ability to enable and disable SMDS pdu violation traps on this logical port. This functionality applies t… |
| 1.3.6.1.4.1.277.1.5.1.1.232 | lportSmdsPduViolThresh | 0 | 0 | This object defines the Smds pdu violation threshold for this logical port. The allowable range of threshold values is 1-255. The… |
| 1.3.6.1.4.1.277.1.5.1.1.233 | lportSmdsPduHdrSip3SaNotFound | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Not… |
| 1.3.6.1.4.1.277.1.5.1.1.234 | lportSmdsPduHdrSip3SaDaOnSamePort | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Da … |
| 1.3.6.1.4.1.277.1.5.1.1.235 | lportSmdsPduHdrSip3DstGaNotFound | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga… |
| 1.3.6.1.4.1.277.1.5.1.1.236 | lportSmdsPduHdrSip3DstIaScrnFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia… |
| 1.3.6.1.4.1.277.1.5.1.1.237 | lportSmdsPduHdrSip3SaValFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Val… |
| 1.3.6.1.4.1.277.1.5.1.1.238 | lportSmdsPduHdrSip3DstIaNotFound | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia… |
| 1.3.6.1.4.1.277.1.5.1.1.239 | lportSmdsPduHdrSip3SrcIaScrnFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Src Ia… |
| 1.3.6.1.4.1.277.1.5.1.1.240 | lportSmdsPduHdrSip3DstGaScrnFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga… |
| 1.3.6.1.4.1.277.1.5.1.1.241 | lportSmdsPduHdrSip3SaTypeInvalid | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Typ… |
| 1.3.6.1.4.1.277.1.5.1.1.242 | lportSmdsPduHdrSip3DaTypeInvalid | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Da Typ… |
| 1.3.6.1.4.1.277.1.5.1.1.243 | lportSmdsPduHdrDxi2LinkIdInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Link Id Invalid. The length of this object … |
| 1.3.6.1.4.1.277.1.5.1.1.244 | lportSmdsPduHdrDxi2CrInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Cr Invalid. The length of this object is 4 … |
| 1.3.6.1.4.1.277.1.5.1.1.245 | lportSmdsPduHdrDxi2CtrlInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ctrl Invalid. The length of this object is … |
| 1.3.6.1.4.1.277.1.5.1.1.246 | lportSmdsPduHdrDxi2StationIdInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Station Id Invalid. The length of this obje… |
| 1.3.6.1.4.1.277.1.5.1.1.247 | lportSmdsPduHdrDxi2AeInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ae Invalid. The length of this object is 4 … |
| 1.3.6.1.4.1.277.1.5.1.1.248 | lportDS0FarendLpbkEnabled | 0 | 0 | Set a single DS0 into farend loopback 1-24. |
| 1.3.6.1.4.1.277.1.5.1.1.249 | lportDS0FarendLpbkDisabled | 0 | 0 | Set a single DS0 out farend loopback 1-24. |
| 1.3.6.1.4.1.277.1.5.1.1.250 | lportTrkProtFailureThreshold | 0 | 0 | The time, measured in seconds, that Trunk Protocol waits before transitioning the state of an unresponsive trunk from UP to DOWN.… |
| 1.3.6.1.4.1.277.1.5.1.1.251 | lportPtr | 0 | 0 | An octet string indicating the lport pointer. |
| 1.3.6.1.4.1.277.1.5.1.1.252 | lportISDNPoolUtil | 0 | 0 | The percent utilization of the B-channel pool that this b-channel belongs to. |
| 1.3.6.1.4.1.277.1.5.1.1.253 | lportISDNIpAddrAssignFail, lportPPPNegotiationFailCode | 0 | 0 | The cause value for why PPP negotiation has failed. |
| 1.3.6.1.4.1.277.1.5.1.1.254 | lportTrkUtilQoS1 | 0 | 0 | An estimate of the real QoS1 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.255 | lportTrkUtilQoS2 | 0 | 0 | An estimate of the real QoS2 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.256 | lportTrkUtilQoS3 | 0 | 0 | An estimate of the real QoS3 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.257 | lportTrkUtilQoS4 | 0 | 0 | An estimate of the real QoS4 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
| 1.3.6.1.4.1.277.1.5.1.1.258 | lportIlmiNumOctetsTx | 0 | 0 | The number of ILMI octets transmitted on this ATM port. |
| 1.3.6.1.4.1.277.1.5.1.1.259 | lportIlmiNumOctetsRx | 0 | 0 | The number of ILMI octets received on this ATM port. |
| 1.3.6.1.4.1.277.1.5.1.1.260 | lportIlmiNumPdusTx | 0 | 0 | The number of ILMI PDU's transmitted on this ATM port. |
| 1.3.6.1.4.1.277.1.5.1.1.261 | lportIlmiNumPdusRx | 0 | 0 | The number of properly formatted ILMI PDU's received on this ATM port. |
| 1.3.6.1.4.1.277.1.5.1.1.262 | lportIlmiNumErrorsRx | 0 | 0 | The number of improperly formatted ILMI PDU's received on this ATM port. |
| 1.3.6.1.4.1.277.1.5.1.1.263 | lportIlmiNumUmePollsTx | 0 | 0 | The number of ILMI polls sent by the UME entity on this ATM DCE port. |
| 1.3.6.1.4.1.277.1.5.1.1.264 | lportIlmiNumUmeResponsesRx | 0 | 0 | The number of ILMI poll responses received by the UME entity on this ATM DCE port. |
| 1.3.6.1.4.1.277.1.5.1.1.265 | lportIlmiVPI | 0 | 0 | The VPI value of the VCC provisioned for the ILMI. The default value is 0. |
| 1.3.6.1.4.1.277.1.5.1.1.266 | lportIlmiVCI | 0 | 0 | The VCI value of the VCC provisioned for the ILMI. The default value is 16. |
| 1.3.6.1.4.1.277.1.5.1.1.267 | lportInCells | 0 | 0 | The total number of cells received |
| 1.3.6.1.4.1.277.1.5.1.1.268 | lportOutCells | 0 | 0 | The total number of cells transmitted |
| 1.3.6.1.4.1.277.1.5.1.1.269 | lportDS1ChannelId | 0 | 0 | The channel id of the DS1 channel for the channelized DS3 IOP. |
| 1.3.6.1.4.1.277.1.5.1.1.270 | lportCDV | 0 | 0 | The Cell Delay Variation of this port measured in microseconds. |
| 1.3.6.1.4.1.277.1.5.1.1.271 | lportAtmTrkIomCktDiagStr | 0 | 0 | Internal diagnostic information. |
| 1.3.6.1.4.1.277.1.5.1.1.272 | lportAtmTrkSpCktDiagStr | 0 | 0 | Internal diagnostic information. |
| 1.3.6.1.4.1.277.1.5.1.1.273 | lportAuthState | 0 | 0 | Authentication enabled for this port, yes or no. |
| 1.3.6.1.4.1.277.1.5.1.1.274 | lportAuthDomainID | 0 | 0 | Authentication Domain ID for this lport. |
| 1.3.6.1.4.1.277.1.5.1.1.275 | lportAuthPPPOption | 0 | 0 | PPP authentication options. |
| 1.3.6.1.4.1.277.1.5.1.1.276 | lportAuthFailReason | 0 | 0 | Reason for authentication failure - trap sent to NMS. |
| ... | ||||