Authentication enabled for this port, yes or no.
Parsed from file cascade.mib.txt
Company: cascade
Module: CASCADE-MIB
Vendor: Cascade Communications
Module: CASCADE-MIB (cascade.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
lportAuthState OBJECT-TYPE SYNTAX INTEGER { auth-enabled (1), auth_disabled (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Authentication enabled for this port, yes or no." ::= { lportEntry 273 }
To many brothers! Only 100 nearest brothers are shown.
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
... | ||||
1.3.6.1.4.1.277.1.5.1.1.223 | lportLossOfStructurePointer | 0 | 0 | The structured CBR card detected a loss of structure pointer condition on this lport for an extended period. |
1.3.6.1.4.1.277.1.5.1.1.224 | lportCbrInsDummyCells | 0 | 0 | The number of dummy cells inserted due to cell loss on a constant bit rate (AAL1) interface. |
1.3.6.1.4.1.277.1.5.1.1.225 | lportRecFifoUnderflowCnt | 0 | 0 | The number of receive FIFO underflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued in… |
1.3.6.1.4.1.277.1.5.1.1.226 | lportRecFifoOverflowCnt | 0 | 0 | The number of receive FIFO overflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued ind… |
1.3.6.1.4.1.277.1.5.1.1.227 | lportCbrLossOfStructurePointerCnt | 0 | 0 | The object counts how often the structured CBR card detected a loss of the structure pointer since the last reset. |
1.3.6.1.4.1.277.1.5.1.1.228 | lportCbrLossOfCellSequenceCnt | 0 | 0 | The number of loss of cell sequence since the last reset. |
1.3.6.1.4.1.277.1.5.1.1.229 | lportShaperId | 0 | 0 | The shaper to be used for this ATM trunk interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card Values: 1..16 |
1.3.6.1.4.1.277.1.5.1.1.230 | lportIlmiPrefixScreenMode, lportDteIlmiPrefixScreenMode | 0 | 0 | The type of screening to apply against dynamic prefixes received from the peer ILMI entity at this DTE port. |
1.3.6.1.4.1.277.1.5.1.1.231 | lportSmdsPduViolTca | 0 | 0 | This object defines the ability to enable and disable SMDS pdu violation traps on this logical port. This functionality applies t… |
1.3.6.1.4.1.277.1.5.1.1.232 | lportSmdsPduViolThresh | 0 | 0 | This object defines the Smds pdu violation threshold for this logical port. The allowable range of threshold values is 1-255. The… |
1.3.6.1.4.1.277.1.5.1.1.233 | lportSmdsPduHdrSip3SaNotFound | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Not… |
1.3.6.1.4.1.277.1.5.1.1.234 | lportSmdsPduHdrSip3SaDaOnSamePort | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Da … |
1.3.6.1.4.1.277.1.5.1.1.235 | lportSmdsPduHdrSip3DstGaNotFound | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga… |
1.3.6.1.4.1.277.1.5.1.1.236 | lportSmdsPduHdrSip3DstIaScrnFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia… |
1.3.6.1.4.1.277.1.5.1.1.237 | lportSmdsPduHdrSip3SaValFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Val… |
1.3.6.1.4.1.277.1.5.1.1.238 | lportSmdsPduHdrSip3DstIaNotFound | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia… |
1.3.6.1.4.1.277.1.5.1.1.239 | lportSmdsPduHdrSip3SrcIaScrnFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Src Ia… |
1.3.6.1.4.1.277.1.5.1.1.240 | lportSmdsPduHdrSip3DstGaScrnFail | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga… |
1.3.6.1.4.1.277.1.5.1.1.241 | lportSmdsPduHdrSip3SaTypeInvalid | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Typ… |
1.3.6.1.4.1.277.1.5.1.1.242 | lportSmdsPduHdrSip3DaTypeInvalid | 0 | 0 | This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Da Typ… |
1.3.6.1.4.1.277.1.5.1.1.243 | lportSmdsPduHdrDxi2LinkIdInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Link Id Invalid. The length of this object … |
1.3.6.1.4.1.277.1.5.1.1.244 | lportSmdsPduHdrDxi2CrInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Cr Invalid. The length of this object is 4 … |
1.3.6.1.4.1.277.1.5.1.1.245 | lportSmdsPduHdrDxi2CtrlInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ctrl Invalid. The length of this object is … |
1.3.6.1.4.1.277.1.5.1.1.246 | lportSmdsPduHdrDxi2StationIdInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Station Id Invalid. The length of this obje… |
1.3.6.1.4.1.277.1.5.1.1.247 | lportSmdsPduHdrDxi2AeInvalid | 0 | 0 | This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ae Invalid. The length of this object is 4 … |
1.3.6.1.4.1.277.1.5.1.1.248 | lportDS0FarendLpbkEnabled | 0 | 0 | Set a single DS0 into farend loopback 1-24. |
1.3.6.1.4.1.277.1.5.1.1.249 | lportDS0FarendLpbkDisabled | 0 | 0 | Set a single DS0 out farend loopback 1-24. |
1.3.6.1.4.1.277.1.5.1.1.250 | lportTrkProtFailureThreshold | 0 | 0 | The time, measured in seconds, that Trunk Protocol waits before transitioning the state of an unresponsive trunk from UP to DOWN.… |
1.3.6.1.4.1.277.1.5.1.1.251 | lportPtr | 0 | 0 | An octet string indicating the lport pointer. |
1.3.6.1.4.1.277.1.5.1.1.252 | lportISDNPoolUtil | 0 | 0 | The percent utilization of the B-channel pool that this b-channel belongs to. |
1.3.6.1.4.1.277.1.5.1.1.253 | lportISDNIpAddrAssignFail, lportPPPNegotiationFailCode | 0 | 0 | The cause value for why PPP negotiation has failed. |
1.3.6.1.4.1.277.1.5.1.1.254 | lportTrkUtilQoS1 | 0 | 0 | An estimate of the real QoS1 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
1.3.6.1.4.1.277.1.5.1.1.255 | lportTrkUtilQoS2 | 0 | 0 | An estimate of the real QoS2 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
1.3.6.1.4.1.277.1.5.1.1.256 | lportTrkUtilQoS3 | 0 | 0 | An estimate of the real QoS3 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
1.3.6.1.4.1.277.1.5.1.1.257 | lportTrkUtilQoS4 | 0 | 0 | An estimate of the real QoS4 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
1.3.6.1.4.1.277.1.5.1.1.258 | lportIlmiNumOctetsTx | 0 | 0 | The number of ILMI octets transmitted on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.259 | lportIlmiNumOctetsRx | 0 | 0 | The number of ILMI octets received on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.260 | lportIlmiNumPdusTx | 0 | 0 | The number of ILMI PDU's transmitted on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.261 | lportIlmiNumPdusRx | 0 | 0 | The number of properly formatted ILMI PDU's received on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.262 | lportIlmiNumErrorsRx | 0 | 0 | The number of improperly formatted ILMI PDU's received on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.263 | lportIlmiNumUmePollsTx | 0 | 0 | The number of ILMI polls sent by the UME entity on this ATM DCE port. |
1.3.6.1.4.1.277.1.5.1.1.264 | lportIlmiNumUmeResponsesRx | 0 | 0 | The number of ILMI poll responses received by the UME entity on this ATM DCE port. |
1.3.6.1.4.1.277.1.5.1.1.265 | lportIlmiVPI | 0 | 0 | The VPI value of the VCC provisioned for the ILMI. The default value is 0. |
1.3.6.1.4.1.277.1.5.1.1.266 | lportIlmiVCI | 0 | 0 | The VCI value of the VCC provisioned for the ILMI. The default value is 16. |
1.3.6.1.4.1.277.1.5.1.1.267 | lportInCells | 0 | 0 | The total number of cells received |
1.3.6.1.4.1.277.1.5.1.1.268 | lportOutCells | 0 | 0 | The total number of cells transmitted |
1.3.6.1.4.1.277.1.5.1.1.269 | lportDS1ChannelId | 0 | 0 | The channel id of the DS1 channel for the channelized DS3 IOP. |
1.3.6.1.4.1.277.1.5.1.1.270 | lportCDV | 0 | 0 | The Cell Delay Variation of this port measured in microseconds. |
1.3.6.1.4.1.277.1.5.1.1.271 | lportAtmTrkIomCktDiagStr | 0 | 0 | Internal diagnostic information. |
1.3.6.1.4.1.277.1.5.1.1.272 | lportAtmTrkSpCktDiagStr | 0 | 0 | Internal diagnostic information. |
1.3.6.1.4.1.277.1.5.1.1.274 | lportAuthDomainID | 0 | 0 | Authentication Domain ID for this lport. |
1.3.6.1.4.1.277.1.5.1.1.275 | lportAuthPPPOption | 0 | 0 | PPP authentication options. |
1.3.6.1.4.1.277.1.5.1.1.276 | lportAuthFailReason | 0 | 0 | Reason for authentication failure - trap sent to NMS. |
1.3.6.1.4.1.277.1.5.1.1.277 | lportEchoRequestOption | 0 | 0 | The sending of Echo Requests enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.278 | lportEchoRequestInterval | 0 | 0 | The # seconds to wait between sending Echo Requests. |
1.3.6.1.4.1.277.1.5.1.1.279 | lportEchoRequestMaxTries | 0 | 0 | The max # times to send an Echo Request without getting a response. |
1.3.6.1.4.1.277.1.5.1.1.280 | lportMultilinkProtocolOption | 0 | 0 | PPP Multilink Protocol enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.281 | lportMultilinkProtocolFailReason | 0 | 0 | Failure to create an MP bundle or to add a link to an MP Bundle - trap sent. |
1.3.6.1.4.1.277.1.5.1.1.282 | lportBandwidthAllocProtocolOption | 0 | 0 | PPP Bandwidth Alloc Protocol enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.283 | lportBandwidthAllocProtocolCallFailReason | 0 | 0 | BAP Call Fail Status code (Q.931 cause code) - trap sent to NMS. |
1.3.6.1.4.1.277.1.5.1.1.284 | lportPrivateNetOverflow | 0 | 0 | Indicates how circuits belonging to private lports are handled, when the resources of the network have become exhausted. If set t… |
1.3.6.1.4.1.277.1.5.1.1.285 | lportCbrFifoHalfLength | 0 | 0 | CBR card was never released. Determines the size of the FIFO used on the CBR COBRA. The unit are the number of cells stored in th… |
1.3.6.1.4.1.277.1.5.1.1.286 | lportCustomerID | 0 | 0 | The Customer that owns this lport. For Virtual Private Networking Support. |
1.3.6.1.4.1.277.1.5.1.1.287 | lportCongestThresh0 | 0 | 0 | Congestion threshold #0 for NTM/NDC in cells/second. Used as a severe congestion abatement threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.288 | lportCongestThresh1 | 0 | 0 | Congestion threshold #1 for NTM/NDC in cells/second. Used as a low congestion threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.289 | lportCongestThresh2 | 0 | 0 | Congestion threshold #2 for NTM/NDC in cells/second Used as a high congestion threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.290 | lportCongestThresh3 | 0 | 0 | Congestion threshold #3 for NTM/NDC in cells/second. Used as a severe congestion threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.291 | lportSevereCongestNotifyTime | 0 | 0 | Selects a minimum severe congestion period upon which an alarm is generated on an IOM. Default value is 30 seconds. |
1.3.6.1.4.1.277.1.5.1.1.292 | lportSevereCongestStatus | 0 | 0 | Indicates the state of severe congestion on a logical port. |
1.3.6.1.4.1.277.1.5.1.1.293 | lportSmdsNumInFramesIa | 0 | 0 | Number of SMDS IA Frames received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.294 | lportSmdsNumInBytesIa | 0 | 0 | Number of SMDS IA Bytes received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.295 | lportSmdsNumInFramesGa | 0 | 0 | Number of SMDS GA Frames received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.296 | lportSmdsNumInBytesGa | 0 | 0 | Number of SMDS GA Bytes received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.297 | lportSmdsNumOutFramesIa | 0 | 0 | Number of SMDS IA Frames transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.298 | lportSmdsNumOutBytesIa | 0 | 0 | Number of SMDS IA Bytes transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.299 | lportSmdsNumOutFramesGa | 0 | 0 | Number of SMDS GA Frames transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.300 | lportSmdsNumOutBytesGa | 0 | 0 | Number of SMDS GA Bytes transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.301 | lportAtmTrkCLPOut | 0 | 0 | CLP mapping for circuit data carried over an ATM trunk. If clp_always_0 is selected then all circuit data sent over the ATM trun… |
1.3.6.1.4.1.277.1.5.1.1.302 | lportAtmTrkCLPIn | 0 | 0 | CLP mapping for circuit data received from an ATM trunk. If clp_always_0 is selected then all circuit data received from the ATM… |
1.3.6.1.4.1.277.1.5.1.1.303 | lportAtmTrkEFCIOut | 0 | 0 | EFCI mapping for circuit data carried over an ATM trunk. If efci_always_0 is selected then all circuit data sent over the ATM tr… |
1.3.6.1.4.1.277.1.5.1.1.304 | lportAtmTrkEFCIIn | 0 | 0 | EFCI mapping for circuit data received from an ATM trunk. If efci_always_0 is selected then all circuit data received from the A… |
1.3.6.1.4.1.277.1.5.1.1.305 | lportBadPVCFactor | 0 | 0 | The factor used to determine the threshold for bad PVC detection. Its value ranges from 0 to 32. The relationship between the th… |
1.3.6.1.4.1.277.1.5.1.1.306 | lportAmberReductionPm | 0 | 0 | The percentage of amber frame reduction when mild congestion happens, by default, it is set to 50. |
1.3.6.1.4.1.277.1.5.1.1.307 | lportAmberReductionPs | 0 | 0 | The percentage of amber frame reduction when severe congestion happens, by default, it is set to 75. |
1.3.6.1.4.1.277.1.5.1.1.308 | lportCongestionCheckInterval | 0 | 0 | Specifies the interval (measured in seconds) between successive congestion state checking on a port. Default is 1 second. |
1.3.6.1.4.1.277.1.5.1.1.309 | lportCongestionClearDelay | 0 | 0 | Specifies, the delay (measured in seconds) before congestion clearance message is sent when the congested port becomes less cong… |
1.3.6.1.4.1.277.1.5.1.1.310 | lportNrtsRmGenType | 0 | 0 | The type of RM cells the NRTS processor generates on this lport. |
1.3.6.1.4.1.277.1.5.1.1.311 | lportNrtsRmTermType | 0 | 0 | The type of RM cells the NRTS processor terminates on this lport. |
1.3.6.1.4.1.277.1.5.1.1.312 | lportNrtsEfciCheck | 0 | 0 | Whether the NRTS processor checks the EFCI bit for circuits on this lport when incrementing EFCI counts. |
1.3.6.1.4.1.277.1.5.1.1.313 | lportNrtsBufAlloc | 0 | 0 | Cell buffer size for this lport controlled by the NRTS processor. |
1.3.6.1.4.1.277.1.5.1.1.314 | lportNrtsClp01Thresh | 0 | 0 | The CLP=0+1 threshold for this lport used by the NRTS processor. Must be smaller than the cell buffer size allocated for this lpo… |
1.3.6.1.4.1.277.1.5.1.1.315 | lportNrtsDiscardThresh | 0 | 0 | The CLP=1 discard threshold for this lport used by the NRTS processor. Must be smaller than the CLP=0+1 threshold. May also be us… |
1.3.6.1.4.1.277.1.5.1.1.316 | lportNrtsEfciThresh | 0 | 0 | The EFCI threshold for this lport used by the NRTS processor. Must be smaller than the CLP=0+1 and discard thresholds. |
1.3.6.1.4.1.277.1.5.1.1.317 | lportNrtsRmCellCount | 0 | 0 | The number of RM cells received on this lport by the NRTS processor. |
1.3.6.1.4.1.277.1.5.1.1.318 | lportCloseLoopSwitch | 0 | 0 | Close loop congestion control function switch on this logical port. 0: Close loop control OFF, 1: Close loop control ON. By de… |
1.3.6.1.4.1.277.1.5.1.1.319 | lportAtmVPIStop | 0 | 0 | The stop value for the PVC VPI range. Used only by VP Mux termination lports |
1.3.6.1.4.1.277.1.5.1.1.320 | lportSegmentation | 0 | 0 | Specifies the transportation feature of a trunk port. If enabled, the port cuts user packets into fix-length segments for delive… |
1.3.6.1.4.1.277.1.5.1.1.321 | lportServiceClassType | 0 | 0 | Specifies the service class types to be supported by the logical port. the valid values and their corresponding definitions are:… |
1.3.6.1.4.1.277.1.5.1.1.322 | lportTrkOSPFAreaID | 0 | 0 | OSPF Area ID to which the trunk belongs. Default value is 0.0.0.1 for historical reasons. |
1.3.6.1.4.1.277.1.5.1.1.323 | lportAtmVPIRmtStop | 0 | 0 | RMT VPI range is specified over anOPTimum trunk logical ports. This range falls within the VPI range as specified for SVPs. This … |
... |