The percentage of amber frame reduction when severe congestion happens, by default, it
is set to 75.
Parsed from file cascade.mib.txt
Company: cascade
Module: CASCADE-MIB
Vendor: Cascade Communications
Module: CASCADE-MIB (cascade.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
lportAmberReductionPs OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The percentage of amber frame reduction when severe congestion happens, by default, it is set to 75." ::= {lportEntry 307 }
To many brothers! Only 100 nearest brothers are shown.
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
... | ||||
1.3.6.1.4.1.277.1.5.1.1.257 | lportTrkUtilQoS4 | 0 | 0 | An estimate of the real QoS4 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth. |
1.3.6.1.4.1.277.1.5.1.1.258 | lportIlmiNumOctetsTx | 0 | 0 | The number of ILMI octets transmitted on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.259 | lportIlmiNumOctetsRx | 0 | 0 | The number of ILMI octets received on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.260 | lportIlmiNumPdusTx | 0 | 0 | The number of ILMI PDU's transmitted on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.261 | lportIlmiNumPdusRx | 0 | 0 | The number of properly formatted ILMI PDU's received on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.262 | lportIlmiNumErrorsRx | 0 | 0 | The number of improperly formatted ILMI PDU's received on this ATM port. |
1.3.6.1.4.1.277.1.5.1.1.263 | lportIlmiNumUmePollsTx | 0 | 0 | The number of ILMI polls sent by the UME entity on this ATM DCE port. |
1.3.6.1.4.1.277.1.5.1.1.264 | lportIlmiNumUmeResponsesRx | 0 | 0 | The number of ILMI poll responses received by the UME entity on this ATM DCE port. |
1.3.6.1.4.1.277.1.5.1.1.265 | lportIlmiVPI | 0 | 0 | The VPI value of the VCC provisioned for the ILMI. The default value is 0. |
1.3.6.1.4.1.277.1.5.1.1.266 | lportIlmiVCI | 0 | 0 | The VCI value of the VCC provisioned for the ILMI. The default value is 16. |
1.3.6.1.4.1.277.1.5.1.1.267 | lportInCells | 0 | 0 | The total number of cells received |
1.3.6.1.4.1.277.1.5.1.1.268 | lportOutCells | 0 | 0 | The total number of cells transmitted |
1.3.6.1.4.1.277.1.5.1.1.269 | lportDS1ChannelId | 0 | 0 | The channel id of the DS1 channel for the channelized DS3 IOP. |
1.3.6.1.4.1.277.1.5.1.1.270 | lportCDV | 0 | 0 | The Cell Delay Variation of this port measured in microseconds. |
1.3.6.1.4.1.277.1.5.1.1.271 | lportAtmTrkIomCktDiagStr | 0 | 0 | Internal diagnostic information. |
1.3.6.1.4.1.277.1.5.1.1.272 | lportAtmTrkSpCktDiagStr | 0 | 0 | Internal diagnostic information. |
1.3.6.1.4.1.277.1.5.1.1.273 | lportAuthState | 0 | 0 | Authentication enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.274 | lportAuthDomainID | 0 | 0 | Authentication Domain ID for this lport. |
1.3.6.1.4.1.277.1.5.1.1.275 | lportAuthPPPOption | 0 | 0 | PPP authentication options. |
1.3.6.1.4.1.277.1.5.1.1.276 | lportAuthFailReason | 0 | 0 | Reason for authentication failure - trap sent to NMS. |
1.3.6.1.4.1.277.1.5.1.1.277 | lportEchoRequestOption | 0 | 0 | The sending of Echo Requests enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.278 | lportEchoRequestInterval | 0 | 0 | The # seconds to wait between sending Echo Requests. |
1.3.6.1.4.1.277.1.5.1.1.279 | lportEchoRequestMaxTries | 0 | 0 | The max # times to send an Echo Request without getting a response. |
1.3.6.1.4.1.277.1.5.1.1.280 | lportMultilinkProtocolOption | 0 | 0 | PPP Multilink Protocol enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.281 | lportMultilinkProtocolFailReason | 0 | 0 | Failure to create an MP bundle or to add a link to an MP Bundle - trap sent. |
1.3.6.1.4.1.277.1.5.1.1.282 | lportBandwidthAllocProtocolOption | 0 | 0 | PPP Bandwidth Alloc Protocol enabled for this port, yes or no. |
1.3.6.1.4.1.277.1.5.1.1.283 | lportBandwidthAllocProtocolCallFailReason | 0 | 0 | BAP Call Fail Status code (Q.931 cause code) - trap sent to NMS. |
1.3.6.1.4.1.277.1.5.1.1.284 | lportPrivateNetOverflow | 0 | 0 | Indicates how circuits belonging to private lports are handled, when the resources of the network have become exhausted. If set t… |
1.3.6.1.4.1.277.1.5.1.1.285 | lportCbrFifoHalfLength | 0 | 0 | CBR card was never released. Determines the size of the FIFO used on the CBR COBRA. The unit are the number of cells stored in th… |
1.3.6.1.4.1.277.1.5.1.1.286 | lportCustomerID | 0 | 0 | The Customer that owns this lport. For Virtual Private Networking Support. |
1.3.6.1.4.1.277.1.5.1.1.287 | lportCongestThresh0 | 0 | 0 | Congestion threshold #0 for NTM/NDC in cells/second. Used as a severe congestion abatement threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.288 | lportCongestThresh1 | 0 | 0 | Congestion threshold #1 for NTM/NDC in cells/second. Used as a low congestion threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.289 | lportCongestThresh2 | 0 | 0 | Congestion threshold #2 for NTM/NDC in cells/second Used as a high congestion threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.290 | lportCongestThresh3 | 0 | 0 | Congestion threshold #3 for NTM/NDC in cells/second. Used as a severe congestion threshold on an IOM. |
1.3.6.1.4.1.277.1.5.1.1.291 | lportSevereCongestNotifyTime | 0 | 0 | Selects a minimum severe congestion period upon which an alarm is generated on an IOM. Default value is 30 seconds. |
1.3.6.1.4.1.277.1.5.1.1.292 | lportSevereCongestStatus | 0 | 0 | Indicates the state of severe congestion on a logical port. |
1.3.6.1.4.1.277.1.5.1.1.293 | lportSmdsNumInFramesIa | 0 | 0 | Number of SMDS IA Frames received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.294 | lportSmdsNumInBytesIa | 0 | 0 | Number of SMDS IA Bytes received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.295 | lportSmdsNumInFramesGa | 0 | 0 | Number of SMDS GA Frames received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.296 | lportSmdsNumInBytesGa | 0 | 0 | Number of SMDS GA Bytes received on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.297 | lportSmdsNumOutFramesIa | 0 | 0 | Number of SMDS IA Frames transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.298 | lportSmdsNumOutBytesIa | 0 | 0 | Number of SMDS IA Bytes transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.299 | lportSmdsNumOutFramesGa | 0 | 0 | Number of SMDS GA Frames transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.300 | lportSmdsNumOutBytesGa | 0 | 0 | Number of SMDS GA Bytes transmitted on an SSI/DXI-SNI lport. |
1.3.6.1.4.1.277.1.5.1.1.301 | lportAtmTrkCLPOut | 0 | 0 | CLP mapping for circuit data carried over an ATM trunk. If clp_always_0 is selected then all circuit data sent over the ATM trun… |
1.3.6.1.4.1.277.1.5.1.1.302 | lportAtmTrkCLPIn | 0 | 0 | CLP mapping for circuit data received from an ATM trunk. If clp_always_0 is selected then all circuit data received from the ATM… |
1.3.6.1.4.1.277.1.5.1.1.303 | lportAtmTrkEFCIOut | 0 | 0 | EFCI mapping for circuit data carried over an ATM trunk. If efci_always_0 is selected then all circuit data sent over the ATM tr… |
1.3.6.1.4.1.277.1.5.1.1.304 | lportAtmTrkEFCIIn | 0 | 0 | EFCI mapping for circuit data received from an ATM trunk. If efci_always_0 is selected then all circuit data received from the A… |
1.3.6.1.4.1.277.1.5.1.1.305 | lportBadPVCFactor | 0 | 0 | The factor used to determine the threshold for bad PVC detection. Its value ranges from 0 to 32. The relationship between the th… |
1.3.6.1.4.1.277.1.5.1.1.306 | lportAmberReductionPm | 0 | 0 | The percentage of amber frame reduction when mild congestion happens, by default, it is set to 50. |
1.3.6.1.4.1.277.1.5.1.1.308 | lportCongestionCheckInterval | 0 | 0 | Specifies the interval (measured in seconds) between successive congestion state checking on a port. Default is 1 second. |
1.3.6.1.4.1.277.1.5.1.1.309 | lportCongestionClearDelay | 0 | 0 | Specifies, the delay (measured in seconds) before congestion clearance message is sent when the congested port becomes less cong… |
1.3.6.1.4.1.277.1.5.1.1.310 | lportNrtsRmGenType | 0 | 0 | The type of RM cells the NRTS processor generates on this lport. |
1.3.6.1.4.1.277.1.5.1.1.311 | lportNrtsRmTermType | 0 | 0 | The type of RM cells the NRTS processor terminates on this lport. |
1.3.6.1.4.1.277.1.5.1.1.312 | lportNrtsEfciCheck | 0 | 0 | Whether the NRTS processor checks the EFCI bit for circuits on this lport when incrementing EFCI counts. |
1.3.6.1.4.1.277.1.5.1.1.313 | lportNrtsBufAlloc | 0 | 0 | Cell buffer size for this lport controlled by the NRTS processor. |
1.3.6.1.4.1.277.1.5.1.1.314 | lportNrtsClp01Thresh | 0 | 0 | The CLP=0+1 threshold for this lport used by the NRTS processor. Must be smaller than the cell buffer size allocated for this lpo… |
1.3.6.1.4.1.277.1.5.1.1.315 | lportNrtsDiscardThresh | 0 | 0 | The CLP=1 discard threshold for this lport used by the NRTS processor. Must be smaller than the CLP=0+1 threshold. May also be us… |
1.3.6.1.4.1.277.1.5.1.1.316 | lportNrtsEfciThresh | 0 | 0 | The EFCI threshold for this lport used by the NRTS processor. Must be smaller than the CLP=0+1 and discard thresholds. |
1.3.6.1.4.1.277.1.5.1.1.317 | lportNrtsRmCellCount | 0 | 0 | The number of RM cells received on this lport by the NRTS processor. |
1.3.6.1.4.1.277.1.5.1.1.318 | lportCloseLoopSwitch | 0 | 0 | Close loop congestion control function switch on this logical port. 0: Close loop control OFF, 1: Close loop control ON. By de… |
1.3.6.1.4.1.277.1.5.1.1.319 | lportAtmVPIStop | 0 | 0 | The stop value for the PVC VPI range. Used only by VP Mux termination lports |
1.3.6.1.4.1.277.1.5.1.1.320 | lportSegmentation | 0 | 0 | Specifies the transportation feature of a trunk port. If enabled, the port cuts user packets into fix-length segments for delive… |
1.3.6.1.4.1.277.1.5.1.1.321 | lportServiceClassType | 0 | 0 | Specifies the service class types to be supported by the logical port. the valid values and their corresponding definitions are:… |
1.3.6.1.4.1.277.1.5.1.1.322 | lportTrkOSPFAreaID | 0 | 0 | OSPF Area ID to which the trunk belongs. Default value is 0.0.0.1 for historical reasons. |
1.3.6.1.4.1.277.1.5.1.1.323 | lportAtmVPIRmtStop | 0 | 0 | RMT VPI range is specified over anOPTimum trunk logical ports. This range falls within the VPI range as specified for SVPs. This … |
1.3.6.1.4.1.277.1.5.1.1.327 | lportOutVAvailbwQoS1CPS | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 1 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.328 | lportOutVAvailbwQoS2CPS | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 2 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.329 | lportOutVAvailbwQoS3CPS | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 3 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.330 | lportOutVAvailbwQoS4CPS | 0 | 0 | Current outgoing available virtual bandwidth reserved for QoS class 4 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.331 | lportInVAvailbwQoS1CPS | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 1 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.332 | lportInVAvailbwQoS2CPS | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 2 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.333 | lportInVAvailbwQoS3CPS | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 3 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.334 | lportInVAvailbwQoS4CPS | 0 | 0 | Current incoming available virtual bandwidth reserved for QoS class 4 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.335 | lportOutAllocbwQoS1CPS | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 1 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.336 | lportOutAllocbwQoS2CPS | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 2 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.337 | lportOutAllocbwQoS3CPS | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 3 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.338 | lportOutAllocbwQoS4CPS | 0 | 0 | Current outgoing allocated bandwidth for QoS Class 4 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.339 | lportInAllocbwQoS1CPS | 0 | 0 | Current incoming allocated bandwidth for QoS Class 1 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.340 | lportInAllocbwQoS2CPS | 0 | 0 | Current incoming allocated bandwidth for QoS Class 2 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.341 | lportInAllocbwQoS3CPS | 0 | 0 | Current incoming allocated bandwidth for QoS Class 3 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.342 | lportInAllocbwQoS4CPS | 0 | 0 | Current incoming allocated bandwidth for QoS Class 4 measured in cells per second. |
1.3.6.1.4.1.277.1.5.1.1.343 | lportBundleId | 0 | 0 | The lport Id if the ML Trunk Bundle lport is added to the lport configuration, a zero indicates that is lport is not associated … |
1.3.6.1.4.1.277.1.5.1.1.344 | lportCLLMAdminState | 0 | 0 | The Administrative status of the CLLM notification on this logical port. |
1.3.6.1.4.1.277.1.5.1.1.345 | lportCLLMInterval | 0 | 0 | The time duration between two consecutive CLLM messages sent on a the UNI port, in seconds. The CLLM message is sent as long as … |
1.3.6.1.4.1.277.1.5.1.1.346 | lportCLLMCount | 0 | 0 | This parameter shows the number of CLLM PDUs sent out so far. |
1.3.6.1.4.1.277.1.5.1.1.347 | lportCLLMThresholdNone | 0 | 0 | This is the percentage threshold value of BECN frames received on any VC on this port. If the percentage of BECN frames on recei… |
1.3.6.1.4.1.277.1.5.1.1.348 | lportCLLMThresholdMild | 0 | 0 | This is the percentage threshold value of BECN frames received on any VC on this port. If the percentage of BECN frames received… |
1.3.6.1.4.1.277.1.5.1.1.349 | lportTrkIfInOctetsPeak | 0 | 0 | The 5-minute peak value of the number of input octets (bytes) for a trunk - from Bulk Statistics. Note that this is a 64-bit cou… |
1.3.6.1.4.1.277.1.5.1.1.350 | lportTrkIfOutOctetsPeak | 0 | 0 | The 5-minute peak value of the number of output octets (bytes) for a trunk - from Bulk Statistics. Note that this is a 64-bit co… |
1.3.6.1.4.1.277.1.5.1.1.351 | lportTrkIfInErrorsPeak | 0 | 0 | The 5-minute peak value of the number of input octets (bytes) in error for a trunk - from Bulk Statistics. Note that this is a 6… |
1.3.6.1.4.1.277.1.5.1.1.352 | lportTrkIfOutErrorsPeak | 0 | 0 | The 5-minute peak value of the number of output octets (bytes) in error for a trunk - from Bulk Statistics. Note that this is a … |
1.3.6.1.4.1.277.1.5.1.1.353 | lportFRInOctetsPeak | 0 | 0 | The 5-minute peak value of the number of input octets (bytes) for a Frame Relay UNI/NNI - from Bulk Statistics. |
1.3.6.1.4.1.277.1.5.1.1.354 | lportFROutOctetsPeak | 0 | 0 | The 5-minute peak value of the number of output octets (bytes) for a Frame Relay UNI/NNI - from Bulk Statistics. |
1.3.6.1.4.1.277.1.5.1.1.355 | lportFRInErrorsPeak | 0 | 0 | The 5-minute peak value of the number of input octets (bytes) in error for a Frame Relay UNI/NNI - from Bulk Statistics. |
1.3.6.1.4.1.277.1.5.1.1.356 | lportFROutErrorsPeak | 0 | 0 | The 5-minute peak value of the number of output octets (bytes) in error for a Frame Relay UNI/NNI - from Bulk Statistics. |
1.3.6.1.4.1.277.1.5.1.1.357 | lportCtlUpcEnable | 0 | 0 | Enable/Disable UPC for control circuits |
... |