A factor used to calculate the Initial Cell Rate for a circuit
from its MCR and PCR.
Parsed from file cascade.mib.txt
Company: None
Module: CASCADE-MIB
A factor used to calculate the Initial Cell Rate for a circuit
from its MCR and PCR.
Parsed from file CASCADE-MIB.mib
Module: CASCADE-MIB
Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
cardNrtsIcrFact OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "A factor used to calculate the Initial Cell Rate for a circuit from its MCR and PCR." ::= { cardEntry 124 }
cardNrtsIcrFact OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "A factor used to calculate the Initial Cell Rate for a circuit from its MCR and PCR." ::= { cardEntry 124 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.277.1.7.2.1.74 | cardOperCapability | 0 | 0 | The actual capability of the card |
| 1.3.6.1.4.1.277.1.7.2.1.75 | cardISDNswtype | 0 | 0 | Specifies the ISDN central office switch type for the card. |
| 1.3.6.1.4.1.277.1.7.2.1.76 | cardCpuFgUtil | 0 | 0 | The CPU foreground utilization percentage for packet processing on this intelligent card. |
| 1.3.6.1.4.1.277.1.7.2.1.77 | cardTrkProtState | 0 | 0 | Control for issue of Link Trunk Protocol request frames. If set to disabled, the issue of trunk protocol requests is blocked for… |
| 1.3.6.1.4.1.277.1.7.2.1.78 | cardISDNSigType | 0 | 0 | Specifies whether the ISDN Signalling type is Associated or Non-Facility Associated Signalling |
| 1.3.6.1.4.1.277.1.7.2.1.79 | cardISDNChanId | 0 | 0 | Specifies whether Channel ID assignment is performed by the central office switch or the 9000 - Exclusive (central office) Prefer… |
| 1.3.6.1.4.1.277.1.7.2.1.80 | cardTransmitClockConfig | 0 | 0 | The transmit clock source for timing section of the card |
| 1.3.6.1.4.1.277.1.7.2.1.81 | cardTransmitClockSwitchOver | 0 | 0 | Enable/disable automatic transmit clock source switch-over once a failed clock reference has recovered. |
| 1.3.6.1.4.1.277.1.7.2.1.82 | cardTransmitClockStatus | 0 | 0 | The transmit clock PLL synchronization status of the card |
| 1.3.6.1.4.1.277.1.7.2.1.83 | cardSystemPrimaryClockPortConfig | 0 | 0 | The port number (1-x) on the card that specifies the system primary clock source. A zero specifies no port |
| 1.3.6.1.4.1.277.1.7.2.1.84 | cardSystemPrimaryClockStatus | 0 | 0 | The system primary clock status as detected on the card. |
| 1.3.6.1.4.1.277.1.7.2.1.85 | cardSystemSecondaryClockPortConfig | 0 | 0 | The port number (1 to x) on the card that specifies the system secondary clock source. A zero specifies no port |
| 1.3.6.1.4.1.277.1.7.2.1.86 | cardSystemSecondaryClockStatus | 0 | 0 | The system secondary clock status as detected on the card. |
| 1.3.6.1.4.1.277.1.7.2.1.87 | cardInCells | 0 | 0 | The total number of cells received on this card. |
| 1.3.6.1.4.1.277.1.7.2.1.88 | cardInErrorCells | 0 | 0 | The total number of cells received on this card with HEC error. |
| 1.3.6.1.4.1.277.1.7.2.1.89 | cardInErrorVPIVCI | 0 | 0 | The total number of cells received with HEC invalid VPI, VCI. |
| 1.3.6.1.4.1.277.1.7.2.1.90 | cardOutCells | 0 | 0 | The total number of cells transmitted out of this card |
| 1.3.6.1.4.1.277.1.7.2.1.91 | cardOutDiscardCells | 0 | 0 | The total number of cells discarded due to congestion on this card |
| 1.3.6.1.4.1.277.1.7.2.1.92 | cardQOSQueueSize | 0 | 0 | The ATM QOS queue size (per cell) of each port on the card |
| 1.3.6.1.4.1.277.1.7.2.1.93 | cardLastErrorPort | 0 | 0 | The port number (1 to x) of the last cell with invalid cell header on the card |
| 1.3.6.1.4.1.277.1.7.2.1.94 | cardLastErrorVPI | 0 | 0 | The VPI of the last cell with invalid cell header on the card |
| 1.3.6.1.4.1.277.1.7.2.1.95 | cardLastErrorVCI | 0 | 0 | The VCI of the last cell with invalid cell header on the card |
| 1.3.6.1.4.1.277.1.7.2.1.96 | cardSystemPrimaryClockModeConfig | 0 | 0 | The system primary clock mode. PLCP is for DS3 port only |
| 1.3.6.1.4.1.277.1.7.2.1.97 | cardSystemSecondaryClockModeConfig | 0 | 0 | The system secondary clock mode. PLCP is for DS3 port only |
| 1.3.6.1.4.1.277.1.7.2.1.98 | cardNFBDEStatus | 0 | 0 | Non Fatal Background Diagnostic Error Status |
| 1.3.6.1.4.1.277.1.7.2.1.99 | cardProductCode | 0 | 0 | This card's product code. |
| 1.3.6.1.4.1.277.1.7.2.1.100 | cardMfgPN | 0 | 0 | This card's manufacturing part number. |
| 1.3.6.1.4.1.277.1.7.2.1.101 | cardTotalUpTime | 0 | 0 | This card's total accumulated up time, in hours. |
| 1.3.6.1.4.1.277.1.7.2.1.102 | cardIOAType | 0 | 0 | The type of IOA attached to this card. |
| 1.3.6.1.4.1.277.1.7.2.1.103 | cardIOAHwRev | 0 | 0 | The attached IOA's hardware revision. |
| 1.3.6.1.4.1.277.1.7.2.1.104 | cardIOASerial | 0 | 0 | The attached IOA's serial number. |
| 1.3.6.1.4.1.277.1.7.2.1.105 | cardIOAProductCode | 0 | 0 | The attached IOA's product code. |
| 1.3.6.1.4.1.277.1.7.2.1.106 | cardIOAMfgPN | 0 | 0 | The attached IOA's manufacturing part number. |
| 1.3.6.1.4.1.277.1.7.2.1.107 | cardDS0Support | 0 | 0 | Some B-Stdx T1 boards do not support lpbk. |
| 1.3.6.1.4.1.277.1.7.2.1.108 | cardDiagParamId | 0 | 0 | Parameter identifier for internal diagnostics. |
| 1.3.6.1.4.1.277.1.7.2.1.109 | cardDiagParamValue | 0 | 0 | Value assigned to parameter specified by cardDiagParamId. |
| 1.3.6.1.4.1.277.1.7.2.1.110 | cardBulkStatsPeakCapability | 0 | 0 | Configures capability to collect peak 5-minute statistics. Capability change takes effect upon IOM reboot. |
| 1.3.6.1.4.1.277.1.7.2.1.111 | cardBulkStatsTotalCapability | 0 | 0 | Configures capability to collect total statistics. Capability change takes effect upon IOM reboot. |
| 1.3.6.1.4.1.277.1.7.2.1.112 | cardBulkStatsPeakEnable | 0 | 0 | Reflects the operational state of the peak 5-minute statistic collection on an IOM. For this setting to be enabled, the respectiv… |
| 1.3.6.1.4.1.277.1.7.2.1.113 | cardBulkStatsTotalEnable | 0 | 0 | Reflects the operational state of the total statistic collection on an IOM. For this setting to be enabled, the respective capabi… |
| 1.3.6.1.4.1.277.1.7.2.1.114 | cardBulkStatsBaseCollectPeriod | 0 | 0 | Configures base collection period for bulk statistics on an IOM in minutes. Only the following values are allowed: 15, 20, 30, 60… |
| 1.3.6.1.4.1.277.1.7.2.1.115 | cardNrtsHwRev | 0 | 0 | Hardware revision of the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.116 | cardNrtsOutCellBufSize | 0 | 0 | The size of the NRTS output cell buffer. |
| 1.3.6.1.4.1.277.1.7.2.1.117 | cardNrtsOperState | 0 | 0 | The operational status of the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.118 | cardNrtsAdminState | 0 | 0 | The admin status of the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.119 | cardNrtsCcrmProtocolId | 0 | 0 | The protocol ID field for the CCRM cells. Must be different from the BCM protocol ID. Default is 6. |
| 1.3.6.1.4.1.277.1.7.2.1.120 | cardNrtsBcmProtocolId | 0 | 0 | The protocol ID field for the BCM cells. Must be different from the CCRM protocol ID. Default is 5. |
| 1.3.6.1.4.1.277.1.7.2.1.121 | cardNrtsRmGenInterval | 0 | 0 | The RM cell generation interval in ms. Minimum is 30, maximum is 250, default is 100. |
| 1.3.6.1.4.1.277.1.7.2.1.122 | cardNrtsIdleCktThresh | 0 | 0 | The number of RM cell generation intervals with no cell reception upon which the circuit is declared idle. Minimum is 1, maximum … |
| 1.3.6.1.4.1.277.1.7.2.1.123 | cardNrtsVbrNrtManage | 0 | 0 | Indicates whether VBR NRT traffic should be managed by the NRTS processor. |
| 1.3.6.1.4.1.277.1.7.2.1.125 | cardNrtsMcastDiscardThresh | 0 | 0 | A NRTS discard threshold for the multicast circuits. |
| 1.3.6.1.4.1.277.1.7.2.1.126 | cardNrtsMcastDiscardCount | 0 | 0 | A NRTS discard counter for the multicast circuits. |
| 1.3.6.1.4.1.277.1.7.2.1.127 | cardAdminIOAType | 0 | 0 | The type of IOA attached to this card viewed from NMS. |
| 1.3.6.1.4.1.277.1.7.2.1.128 | cardNrtsMcastRate | 0 | 0 | The NRTS shaping rate for multicast circuits as a fraction of the line rate. |
| 1.3.6.1.4.1.277.1.7.2.1.129 | cardMonStatus | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.7.2.1.130 | cardImageSetA | 0 | 0 | The infomation of image SetA which contains 4 elements, such as Part#, Revision, Size and Description. The separator, between ele… |
| 1.3.6.1.4.1.277.1.7.2.1.131 | cardImageSetB | 0 | 0 | The same DESCRIPTION as cardImageSetA but image SetB. |
| 1.3.6.1.4.1.277.1.7.2.1.132 | cardMacAddress | 0 | 0 | ethernet MAC address of the card if there is an ethernet interface. Currently only CP cards may have ethernet. Cards without ethe… |
| 1.3.6.1.4.1.277.1.7.2.1.133 | cardFlashRev | 0 | 0 | The boot flash rev number. |
| 1.3.6.1.4.1.277.1.7.2.1.134 | cardRequiredCapabilityBitmask | 0 | 0 | Bitmask indicating this cards' required capabilities based on configured features. A bit is set to one if the corresponding capa… |
| 1.3.6.1.4.1.277.1.7.2.1.135 | cardOperCapabilityBitmask | 0 | 0 | Bitmask indicating this cards' actual capabilities. A bit is set to one if the corresponding capability is supported. This variab… |
| 1.3.6.1.4.1.277.1.7.2.1.136 | cardDslModule | 0 | 0 | This is for Dynamic Software Loadl You can type: ModuleName Version, ModuleName Version, ... to load modules. |
| 1.3.6.1.4.1.277.1.7.2.1.137 | cardIPTableSize | 0 | 0 | The maximum number of IP routing table entries supported by the card. If set to 0, routing table size is assumed unlimited. |
| 1.3.6.1.4.1.277.1.7.2.1.138 | cardIPTableState | 0 | 0 | State of the card's IP routing table. If set to marginal, the routing table maximum size has been exceeded. and all routes except… |
| 1.3.6.1.4.1.277.1.7.2.1.139 | cardATMTcaInBufOverflowAlertPeriod | 0 | 0 | The atm tca ingress buffer overflow alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.140 | cardATMTcaInBufOverflowThresh | 0 | 0 | The atm tca ingress buffer overflow threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.141 | cardATMTcaInInvalidVpiVciAlertPeriod | 0 | 0 | The atm tca ingress invalid vpi/vci alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.142 | cardATMTcaInInvalidVpiVciThresh | 0 | 0 | The atm tca ingress invalid vpi/vci threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.143 | cardATMTcaInATMDCFullAlertPeriod | 0 | 0 | The atm tca ingress ATM DC full alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.144 | cardATMTcaInATMDCFullThresh | 0 | 0 | The atm tca ingress ATM DC full threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.145 | cardATMTcaEnable | 0 | 0 | The atm tca enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.146 | cardATMTcaId | 0 | 0 | This object identifies the the most recently declared card ATM threshold crossing alert |
| 1.3.6.1.4.1.277.1.7.2.1.147 | cardATMTcaECidLookupFailureAlertPeriod | 0 | 0 | The atm tca ingress buffer overflow alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.148 | cardATMTcaECidLookupThresh | 0 | 0 | The atm tca ingress buffer overflow threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.149 | cardATMTcaSPPearlOCbrFailureAlertPeriod | 0 | 0 | The atm tca sp pearl overflow CBR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.150 | cardATMTcaSPPearlOCbrThresh | 0 | 0 | The atm tca sp pearl overflow CBR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.151 | cardATMTcaSPPearlOAbrFailureAlertPeriod | 0 | 0 | The atm tca sp pearl overflow ABR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.152 | cardATMTcaSPPearlOAbrThresh | 0 | 0 | The atm tca sp pearl overflow ABR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.153 | cardATMTcaSPPearlOVbr1FailureAlertPeriod | 0 | 0 | The atm tca sp pearl overflow VBR1 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.154 | cardATMTcaSPPearlOVbr1Thresh | 0 | 0 | The atm tca sp pearl overflow VBR1 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.155 | cardATMTcaSPPearlOVbr2FailureAlertPeriod | 0 | 0 | The atm tca sp pearl overflow VBR2 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.156 | cardATMTcaSPPearlOVbr2Thresh | 0 | 0 | The atm tca sp pearl overflow VBR2 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.157 | cardATMTcaSPPearlGCbrFailureAlertPeriod | 0 | 0 | The atm tca sp pearl congestion CBR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.158 | cardATMTcaSPPearlGCbrThresh | 0 | 0 | The atm tca sp pearl congestion CBR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.159 | cardATMTcaSPPearlGAbrFailureAlertPeriod | 0 | 0 | The atm tca sp pearl congestion ABR alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.160 | cardATMTcaSPPearlGAbrThresh | 0 | 0 | The atm tca sp pearl congestion ABR threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.161 | cardATMTcaSPPearlGVbr1FailureAlertPeriod | 0 | 0 | The atm tca sp pearl congestion VBR1 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.162 | cardATMTcaSPPearlGVbr1Thresh | 0 | 0 | The atm tca sp pearl congestion VBR1 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.163 | cardATMTcaSPPearlGVbr2FailureAlertPeriod | 0 | 0 | The atm tca sp pearl congestion VBR2 alert period (in min). |
| 1.3.6.1.4.1.277.1.7.2.1.164 | cardATMTcaSPPearlGVbr2Thresh | 0 | 0 | The atm tca sp pearl congestion VBR2 threshold. |
| 1.3.6.1.4.1.277.1.7.2.1.165 | cardATMTcaSPEnable | 0 | 0 | The atm tca SP enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.166 | cardSPEFCIEnable | 0 | 0 | The atm EFCI marking enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.167 | cardSPClpEnable | 0 | 0 | The atm CLP-1 enable/disable. |
| 1.3.6.1.4.1.277.1.7.2.1.168 | spATMTcaId | 0 | 0 | This object identifies the the most recently declared sp ATM threshold crossing alert and first byte is used to indicate the swit… |
| 1.3.6.1.4.1.277.1.7.2.1.169 | cardSubcardToRedundant | 0 | 0 | Commands the card to initiate an immediate protection switch on the identified subcard that it controls. This causes control to b… |
| 1.3.6.1.4.1.277.1.7.2.1.170 | cardMemory5Usage | 0 | 0 | The bank5 memory utilization, in terms of free bytes, for CP Oynx card only. |
| 1.3.6.1.4.1.277.1.7.2.1.171 | cardSF1OperStatus | 0 | 0 | The current status of Switch Fabric 1 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.172 | cardSF2OperStatus | 0 | 0 | The current status of Switch Fabric 2 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.173 | cardTM1OperStatus | 0 | 0 | The current status of Timing Module 1 (GX550). |
| 1.3.6.1.4.1.277.1.7.2.1.174 | cardTM2OperStatus | 0 | 0 | The current status of Timing Module 2 (GX550). |
| ... | ||||