The temperature range that controls output when the
selected control sensor temperature is below the
setpoint. At the bottom of this range, the reheat
mode outputs at 100%. The deadband does not apply to
PID-controlled modes. Measured in tenths of degrees
Celsius.
A value of -2147483648 indicates that this OID does
not apply to this device due to its configuration.
Parsed from file powernet.mib.txt
Company: None
Module: PowerNet-MIB
The temperature range that controls output when the
selected control sensor temperature is below the
setpoint. At the bottom of this range, the reheat
mode outputs at 100%. The deadband does not apply to
PID-controlled modes. Measured in tenths of degrees
Celsius.
A value of -2147483648 indicates that this OID does
not apply to this device due to its configuration.
Parsed from file PowerNet-MIB.mib
Module: PowerNet-MIB
airFMSysReheatDeadbandC OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The temperature range that controls output when the selected control sensor temperature is below the setpoint. At the bottom of this range, the reheat mode outputs at 100%. The deadband does not apply to PID-controlled modes. Measured in tenths of degrees Celsius. A value of -2147483648 indicates that this OID does not apply to this device due to its configuration." ::= { airFMSysReheat 5 }
Vendor: American Power Conversion Corp.
Module: PowerNet-MIB
[Automatically extracted from oidview.com]
airFMSysReheatDeadbandC OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The temperature range that controls output when the selected control sensor temperature is below the setpoint. At the bottom of this range, the reheat mode outputs at 100%. The deadband does not apply to PID-controlled modes. Measured in tenths of degrees Celsius. A value of -2147483648 indicates that this OID does not apply to this device due to its configuration." ::= { airFMSysReheat 5 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.318.1.1.13.1.4.8.5.0 | airFMSysReheatDeadbandC | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.318.1.1.13.1.4.8.1 | airFMSysReheatState | 1 | 1 | Set the mode to enabled or disabled. Disabled modes will not operate, and you cannot make changes to their settings while they ar… |
1.3.6.1.4.1.318.1.1.13.1.4.8.2 | airFMSysReheatEssFunction | 1 | 1 | Set the priority of the mode for alarms and events with the nonessential stop behavior. Nonessential modes are disabled during no… |
1.3.6.1.4.1.318.1.1.13.1.4.8.3 | airFMSysReheatSetpointC | 1 | 1 | The target value for the selected control sensor air for this mode. It must be at least 1.0 C below the cooling setpoint. Measur… |
1.3.6.1.4.1.318.1.1.13.1.4.8.4 | airFMSysReheatSetpointF | 1 | 1 | The target value for the selected control sensor air for this mode. It must be at least 1.0 C below the cooling setpoint. Measur… |
1.3.6.1.4.1.318.1.1.13.1.4.8.6 | airFMSysReheatDeadbandF | 1 | 1 | The temperature range that controls output when the selected control sensor temperature is below the setpoint. At the bottom of t… |
1.3.6.1.4.1.318.1.1.13.1.4.8.7 | airFMSysReheatPIDMethod | 1 | 1 | Set the multipliers that the PID algorithm will use to calculate the output. Proportional, Proportional + Integral, or Proportion… |
1.3.6.1.4.1.318.1.1.13.1.4.8.8 | airFMSysReheatPIDGainP | 1 | 1 | Set the proportional multiplier to correct for differences between the selected control sensor actual temperature and the setpoin… |
1.3.6.1.4.1.318.1.1.13.1.4.8.9 | airFMSysReheatPIDResetRateI | 1 | 1 | Set the integral multiplier to correct for the proportional offset. Measured in %/(C * min). A value of -2147483648 indicates th… |
1.3.6.1.4.1.318.1.1.13.1.4.8.10 | airFMSysReheatPIDDerivativeD | 1 | 1 | Set the derivative multiplier to counteract overshoot and droop during changes in the room load. Measured in %/(C / min). A value… |