Set the multipliers that the PID algorithm will use
to calculate the output. Proportional,
Proportional + Integral, or Proportional + Integral
+ Derivative.
A value of notApplicable indicates that this OID does
not apply to this device due to its configuration.
Parsed from file powernet.mib.txt
Company: None
Module: PowerNet-MIB
Set the multipliers that the PID algorithm will use
to calculate the output. Proportional,
Proportional + Integral, or Proportional + Integral
+ Derivative.
A value of notApplicable indicates that this OID does
not apply to this device due to its configuration.
Parsed from file PowerNet-MIB.mib
Module: PowerNet-MIB
airFMSysReheatPIDMethod OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), p (2), pi (3), pid (4) } ACCESS read-write STATUS mandatory DESCRIPTION "Set the multipliers that the PID algorithm will use to calculate the output. Proportional, Proportional + Integral, or Proportional + Integral + Derivative. A value of notApplicable indicates that this OID does not apply to this device due to its configuration." ::= { airFMSysReheat 7 }
Vendor: American Power Conversion Corp.
Module: PowerNet-MIB
[Automatically extracted from oidview.com]
airFMSysReheatPIDMethod OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), p (2), pi (3), pid (4) } ACCESS read-write STATUS mandatory DESCRIPTION "Set the multipliers that the PID algorithm will use to calculate the output. Proportional, Proportional + Integral, or Proportional + Integral + Derivative. A value of notApplicable indicates that this OID does not apply to this device due to its configuration." ::= { airFMSysReheat 7 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.318.1.1.13.1.4.8.7.0 | airFMSysReheatPIDMethod | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.318.1.1.13.1.4.8.1 | airFMSysReheatState | 1 | 1 | Set the mode to enabled or disabled. Disabled modes will not operate, and you cannot make changes to their settings while they ar… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.2 | airFMSysReheatEssFunction | 1 | 1 | Set the priority of the mode for alarms and events with the nonessential stop behavior. Nonessential modes are disabled during no… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.3 | airFMSysReheatSetpointC | 1 | 1 | The target value for the selected control sensor air for this mode. It must be at least 1.0 C below the cooling setpoint. Measur… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.4 | airFMSysReheatSetpointF | 1 | 1 | The target value for the selected control sensor air for this mode. It must be at least 1.0 C below the cooling setpoint. Measur… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.5 | airFMSysReheatDeadbandC | 1 | 1 | The temperature range that controls output when the selected control sensor temperature is below the setpoint. At the bottom of t… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.6 | airFMSysReheatDeadbandF | 1 | 1 | The temperature range that controls output when the selected control sensor temperature is below the setpoint. At the bottom of t… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.8 | airFMSysReheatPIDGainP | 1 | 1 | Set the proportional multiplier to correct for differences between the selected control sensor actual temperature and the setpoin… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.9 | airFMSysReheatPIDResetRateI | 1 | 1 | Set the integral multiplier to correct for the proportional offset. Measured in %/(C * min). A value of -2147483648 indicates th… |
| 1.3.6.1.4.1.318.1.1.13.1.4.8.10 | airFMSysReheatPIDDerivativeD | 1 | 1 | Set the derivative multiplier to counteract overshoot and droop during changes in the room load. Measured in %/(C / min). A value… |