This variable indicates the Path Status of the interface. It is defined in
the SONET IETF draft path configuration table as sonetPathStatus. The variable
is a bit map represented as a sum, therefore, it can represent multiple
defects simultaneously. The sonetPathNoDefect should be set if and only if no
other flag is set.
The various bit positions are:
1 sonetPathNoDefect
2 sonetPathLOP Path Loss Of Pointer was detected. Path LOP is declared
when a 'normal pointer value' is not found for eight
consecutive frames.
4 sonetPathAIS Path Alarm Indication Signal was detected. Path AIS is
asserted when an all ones pattern is detected in the
pointer bytes (H1 and H2) for three consecutive frames.
8 sonetPathRDI Path RDI alarm has been detected. RDI alarm is
declared when bit 5 of the path status byte is high for
ten consecutive frames.
16 sonetPathUnequiped
Path is not provisioned (idle).
32 sonetPathSignalLabelMismatch
A received Path Signal Label mismatch. A received
Signal Label is considered mismatched if it does not
equal either the locally provisioned value or the value
'equipped non-specific' (1 hex).
Parsed from file fore-sonet.mib.txt
Company: None
Module: Fore-SONET-MIB
This variable indicates the Path Status of the interface. It is defined in
the SONET IETF draft path configuration table as sonetPathStatus. The variable
is a bit map represented as a sum, therefore, it can represent multiple
defects simultaneously. The sonetPathNoDefect should be set if and only if no
other flag is set.
The various bit positions are:
1 sonetPathNoDefect
2 sonetPathLOP Path Loss Of Pointer was detected. Path LOP is declared
when a 'normal pointer value' is not found for eight
consecutive frames.
4 sonetPathAIS Path Alarm Indication Signal was detected. Path AIS is
asserted when an all ones pattern is detected in the
pointer bytes (H1 and H2) for three consecutive frames.
8 sonetPathRDI Path RDI alarm has been detected. RDI alarm is
declared when bit 5 of the path status byte is high for
ten consecutive frames.
16 sonetPathUnequiped
Path is not provisioned (idle).
32 sonetPathSignalLabelMismatch
A received Path Signal Label mismatch. A received
Signal Label is considered mismatched if it does not
equal either the locally provisioned value or the value
'equipped non-specific' (1 hex).
Parsed from file Fore-SONET-MIB.mib
Module: Fore-SONET-MIB
Vendor: Fore Systems, Inc.
Module: Fore-SONET-MIB
[Automatically extracted from oidview.com]
sonetPathStatus OBJECT-TYPE SYNTAX INTEGER (1..62) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Path Status of the interface. It is defined in the SONET IETF draft path configuration table as sonetPathStatus. The variable is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetPathNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetPathNoDefect 2 sonetPathLOP Path Loss Of Pointer was detected. Path LOP is declared when a 'normal pointer value' is not found for eight consecutive frames. 4 sonetPathAIS Path Alarm Indication Signal was detected. Path AIS is asserted when an all ones pattern is detected in the pointer bytes (H1 and H2) for three consecutive frames. 8 sonetPathRDI Path RDI alarm has been detected. RDI alarm is declared when bit 5 of the path status byte is high for ten consecutive frames. 16 sonetPathUnequiped Path is not provisioned (idle). 32 sonetPathSignalLabelMismatch A received Path Signal Label mismatch. A received Signal Label is considered mismatched if it does not equal either the locally provisioned value or the value 'equipped non-specific' (1 hex)." DEFVAL { 1 } ::= { sonetConfEntry 15 }
sonetPathStatus OBJECT-TYPE SYNTAX INTEGER (1..62) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Path Status of the interface. It is defined in the SONET IETF draft path configuration table as sonetPathStatus. The variable is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sonetPathNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sonetPathNoDefect 2 sonetPathLOP Path Loss Of Pointer was detected. Path LOP is declared when a 'normal pointer value' is not found for eight consecutive frames. 4 sonetPathAIS Path Alarm Indication Signal was detected. Path AIS is asserted when an all ones pattern is detected in the pointer bytes (H1 and H2) for three consecutive frames. 8 sonetPathRDI Path RDI alarm has been detected. RDI alarm is declared when bit 5 of the path status byte is high for ten consecutive frames. 16 sonetPathUnequiped Path is not provisioned (idle). 32 sonetPathSignalLabelMismatch A received Path Signal Label mismatch. A received Signal Label is considered mismatched if it does not equal either the locally provisioned value or the value 'equipped non-specific' (1 hex)." DEFVAL { 1 } ::= { sonetConfEntry 15 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.1 | sonetConfBoard | 0 | 0 | The index of this port's switch board. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.2 | sonetConfModule | 0 | 0 | The network module of this port. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.3 | sonetConfPort | 0 | 0 | The number of this port. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.4 | sonetLineType | 0 | 0 | This variable describes the line type for this interface. The line type for optical SONET signals may be single-mode (short or l… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.5 | sonetLineCoding | 0 | 0 | This variable describes the line coding for this interface. The B3ZS and CMI are used for electrical SONET signals (STS-1 and ST… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.6 | sonetFramingStandardDefault | 0 | 0 | This variable identify the default value of the framing standard that is used by this port (SONET or SDH). |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.7 | sonetFramingStandardOper | 0 | 0 | This variable identify the operational value of the framing standard that is used by this port (SONET or SDH). |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.8 | sonetPathWidth | 0 | 0 | This variable indicates the type of the SONET Path. Assigned types are the STS-Nc Synchronous Payload Envelopes where N=1,3,9,12… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.9 | sonetLoopbackConfig | 0 | 0 | This variable represents the current loopback status of the SONET interface. The possible values are: sonetNoLoop (1) means that t… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.10 | sonetTxClockSource | 0 | 0 | The source of the transmit clock. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.11 | sonetRxScrambling | 0 | 0 | This variable indicates whether the information is being descrambled on receiving. It should be set the same as the transmitting… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.12 | sonetTxScrambling | 0 | 0 | This variable indicates whether the information (48 octet payload) is being scrambled before transmitting. It should be set the … |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.13 | sonetSectionStatus | 0 | 0 | This variable indicates the Section Status of the interface. It is defined in the SONET IETF draft section configuration table a… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.14 | sonetLineStatus | 0 | 0 | This variable indicates the Line Status of the interface. A similar variable is defined in the SONET IETF draft line configurati… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.16 | sonetIdleUnassignedCells | 0 | 0 | This variable indicates the type of cells that should be sent in case there is no data to send. According to the ATM Forum, Unas… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.17 | sonetAtmStatus | 0 | 0 | This variable indicates the ATM Status of the interface. The variable is a bit map represented as a sum, therefore, it can repr… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.18 | sonetLineAis | 0 | 0 | This variable controls the insertion of line alarm indication signal (AIS_L). When set to sonetLineAisOn, AIS is inserted into t… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.19 | sonetLineRdi | 0 | 0 | The variable controls the insertion of Line Remote Defect Indication (RDI_L). When set to sonetLineRdiAuto, RDI_L is automatical… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.20 | sonetPathAis | 0 | 0 | This variable controls the insertion of STS Path Alarm Indication Signal (AIS_P). When set to sonetPathAisOn, the complete SPE, … |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.21 | sonetPathRdi | 0 | 0 | This variable controls the insertion of Path Remote Defect Indication (RDI_P). When set to sonetPathRdiAuto, RDI_P is automatica… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.22 | sonetFebe | 0 | 0 | This variable controls the insertion of line and path far end block errors. When set to sonetFebeAuto, one line or path FEBE is … |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.23 | sonetRxPathSignalLabel | 0 | 0 | This variable contains the path signal label byte (C2). The value in this variable is updated to a new path signal label value i… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.24 | sonetTxPathSignalLabel | 0 | 0 | This variable controls the transmit path signal label. The default value for ATM is 0x13 (19 decimal). |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.25 | sonetArbitraryPointer | 0 | 0 | This variable controls bits APTR[9:0] of arbitrary pointer register. It may be used along with the sonetPathPointerDiagnostic va… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.26 | sonetSectionDiagnostic | 0 | 0 | This variable controls the insertion of various types of section diagnostic bit patterns in the transmit stream. It is a bit map… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.27 | sonetLineDiagnostic | 0 | 0 | This variable controls the insertion of various types of line diagnostic bit patterns in the transmit stream. It is a bit map th… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.28 | sonetPathDiagnostic | 0 | 0 | This variable controls the insertion of various types of path diagnostic bit patterns in the transmit stream. It is a bit map th… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.29 | sonetPathPointerDiagnostic | 0 | 0 | This variable controls the insertion of various types of path pointer diagnostic bit patterns in the transmit stream. It is a bi… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.30 | sonetAtmDiagnostic | 0 | 0 | This variable controls the insertion of various types of atm diagnostic bit patterns in the transmit stream. It is a bit map tha… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.31 | sonetLineBipThrSeconds | 0 | 0 | This variable represents the consecutive number of BAD/GOOD seconds to detect/clear a B2 byte Line Bit Interleaved Parity (BIP) D… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.32 | sonetLineBipThrErrors | 0 | 0 | This variable is a threshold for the number of B2 byte Line Bit Interleaved Parity (BIP) Errors per second and is used as a param… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.33 | sonetLineBipFailEnable | 0 | 0 | This variable controls whether declaration of a Line BIP Defect forces the port's operState to Down. This variable is only applic… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.34 | sonetLineSignalDegradeBer | 0 | 0 | This is the exponent of 10 for the current signal degrade bit error rate (BER) threshold for this port. The value -7, for example… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.35 | sonetLineSignalFailBer | 0 | 0 | This is the exponent of 10 for the current signal fail bit error rate (BER) threshold for this port. The value -4, for example, r… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.36 | sonetLineBerErrorModel | 0 | 0 | This is the error distribution model to be used to identify signal degrade and signal fail conditions. errorModelRandom selects a… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.37 | sonetLineBerState | 0 | 0 | This value describes the current state of the port as determined through bit error rate analysis. |