This variable is a threshold for the number of B2 byte
Line Bit Interleaved Parity (BIP) Errors per second
and is used as a parameter to the Line BIP Defect. If
the number of errors exceeds the threshold, the
particular second is declared BAD, otherwise it is
declared GOOD. This variable is only applicable when
sonetLineBerErrorModel is set to errorModelBurst.
Parsed from file fore-sonet.mib.txt
Company: None
Module: Fore-SONET-MIB
This variable is a threshold for the number of B2 byte
Line Bit Interleaved Parity (BIP) Errors per second
and is used as a parameter to the Line BIP Defect. If
the number of errors exceeds the threshold, the
particular second is declared BAD, otherwise it is
declared GOOD. This variable is only applicable when
sonetLineBerErrorModel is set to errorModelBurst.
Parsed from file Fore-SONET-MIB.mib
Module: Fore-SONET-MIB
Vendor: Fore Systems, Inc.
Module: Fore-SONET-MIB
[Automatically extracted from oidview.com]
sonetLineBipThrErrors OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is a threshold for the number of B2 byte Line Bit Interleaved Parity (BIP) Errors per second and is used as a parameter to the Line BIP Defect. If the number of errors exceeds the threshold, the particular second is declared BAD, otherwise it is declared GOOD. This variable is only applicable when sonetLineBerErrorModel is set to errorModelBurst." ::= { sonetConfEntry 32 }
sonetLineBipThrErrors OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is a threshold for the number of B2 byte Line Bit Interleaved Parity (BIP) Errors per second and is used as a parameter to the Line BIP Defect. If the number of errors exceeds the threshold, the particular second is declared BAD, otherwise it is declared GOOD. This variable is only applicable when sonetLineBerErrorModel is set to errorModelBurst." ::= { sonetConfEntry 32 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.1 | sonetConfBoard | 0 | 0 | The index of this port's switch board. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.2 | sonetConfModule | 0 | 0 | The network module of this port. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.3 | sonetConfPort | 0 | 0 | The number of this port. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.4 | sonetLineType | 0 | 0 | This variable describes the line type for this interface. The line type for optical SONET signals may be single-mode (short or l… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.5 | sonetLineCoding | 0 | 0 | This variable describes the line coding for this interface. The B3ZS and CMI are used for electrical SONET signals (STS-1 and ST… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.6 | sonetFramingStandardDefault | 0 | 0 | This variable identify the default value of the framing standard that is used by this port (SONET or SDH). |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.7 | sonetFramingStandardOper | 0 | 0 | This variable identify the operational value of the framing standard that is used by this port (SONET or SDH). |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.8 | sonetPathWidth | 0 | 0 | This variable indicates the type of the SONET Path. Assigned types are the STS-Nc Synchronous Payload Envelopes where N=1,3,9,12… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.9 | sonetLoopbackConfig | 0 | 0 | This variable represents the current loopback status of the SONET interface. The possible values are: sonetNoLoop (1) means that t… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.10 | sonetTxClockSource | 0 | 0 | The source of the transmit clock. |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.11 | sonetRxScrambling | 0 | 0 | This variable indicates whether the information is being descrambled on receiving. It should be set the same as the transmitting… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.12 | sonetTxScrambling | 0 | 0 | This variable indicates whether the information (48 octet payload) is being scrambled before transmitting. It should be set the … |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.13 | sonetSectionStatus | 0 | 0 | This variable indicates the Section Status of the interface. It is defined in the SONET IETF draft section configuration table a… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.14 | sonetLineStatus | 0 | 0 | This variable indicates the Line Status of the interface. A similar variable is defined in the SONET IETF draft line configurati… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.15 | sonetPathStatus | 0 | 0 | This variable indicates the Path Status of the interface. It is defined in the SONET IETF draft path configuration table as sone… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.16 | sonetIdleUnassignedCells | 0 | 0 | This variable indicates the type of cells that should be sent in case there is no data to send. According to the ATM Forum, Unas… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.17 | sonetAtmStatus | 0 | 0 | This variable indicates the ATM Status of the interface. The variable is a bit map represented as a sum, therefore, it can repr… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.18 | sonetLineAis | 0 | 0 | This variable controls the insertion of line alarm indication signal (AIS_L). When set to sonetLineAisOn, AIS is inserted into t… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.19 | sonetLineRdi | 0 | 0 | The variable controls the insertion of Line Remote Defect Indication (RDI_L). When set to sonetLineRdiAuto, RDI_L is automatical… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.20 | sonetPathAis | 0 | 0 | This variable controls the insertion of STS Path Alarm Indication Signal (AIS_P). When set to sonetPathAisOn, the complete SPE, … |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.21 | sonetPathRdi | 0 | 0 | This variable controls the insertion of Path Remote Defect Indication (RDI_P). When set to sonetPathRdiAuto, RDI_P is automatica… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.22 | sonetFebe | 0 | 0 | This variable controls the insertion of line and path far end block errors. When set to sonetFebeAuto, one line or path FEBE is … |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.23 | sonetRxPathSignalLabel | 0 | 0 | This variable contains the path signal label byte (C2). The value in this variable is updated to a new path signal label value i… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.24 | sonetTxPathSignalLabel | 0 | 0 | This variable controls the transmit path signal label. The default value for ATM is 0x13 (19 decimal). |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.25 | sonetArbitraryPointer | 0 | 0 | This variable controls bits APTR[9:0] of arbitrary pointer register. It may be used along with the sonetPathPointerDiagnostic va… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.26 | sonetSectionDiagnostic | 0 | 0 | This variable controls the insertion of various types of section diagnostic bit patterns in the transmit stream. It is a bit map… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.27 | sonetLineDiagnostic | 0 | 0 | This variable controls the insertion of various types of line diagnostic bit patterns in the transmit stream. It is a bit map th… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.28 | sonetPathDiagnostic | 0 | 0 | This variable controls the insertion of various types of path diagnostic bit patterns in the transmit stream. It is a bit map th… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.29 | sonetPathPointerDiagnostic | 0 | 0 | This variable controls the insertion of various types of path pointer diagnostic bit patterns in the transmit stream. It is a bi… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.30 | sonetAtmDiagnostic | 0 | 0 | This variable controls the insertion of various types of atm diagnostic bit patterns in the transmit stream. It is a bit map tha… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.31 | sonetLineBipThrSeconds | 0 | 0 | This variable represents the consecutive number of BAD/GOOD seconds to detect/clear a B2 byte Line Bit Interleaved Parity (BIP) D… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.33 | sonetLineBipFailEnable | 0 | 0 | This variable controls whether declaration of a Line BIP Defect forces the port's operState to Down. This variable is only applic… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.34 | sonetLineSignalDegradeBer | 0 | 0 | This is the exponent of 10 for the current signal degrade bit error rate (BER) threshold for this port. The value -7, for example… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.35 | sonetLineSignalFailBer | 0 | 0 | This is the exponent of 10 for the current signal fail bit error rate (BER) threshold for this port. The value -4, for example, r… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.36 | sonetLineBerErrorModel | 0 | 0 | This is the error distribution model to be used to identify signal degrade and signal fail conditions. errorModelRandom selects a… |
| 1.3.6.1.4.1.326.2.2.1.1.4.1.1.1.37 | sonetLineBerState | 0 | 0 | This value describes the current state of the port as determined through bit error rate analysis. |