This group contains various low memory conditions.
Parsed from file LIEBERT_GP_COND.MIB.txt
Company: None
Module: LIEBERT-GP-CONDITIONS-MIB
This group contains various low memory conditions.
Parsed from file LIEBERT-GP-CONDITIONS-MIB.mib
Module: LIEBERT-GP-CONDITIONS-MIB
Vendor: Emerson Computer PowerRoger Draper
Module: LIEBERT-GP-CONDITIONS-MIB
[Automatically extracted from oidview.com]
lgpConditionLowMemoryGroup OBJECT-IDENTITY STATUS current DESCRIPTION "This group contains various low memory conditions." ::= { lgpConditionsWellKnown 160 }
lgpConditionLowMemoryGroup OBJECT-IDENTITY STATUS current DESCRIPTION "This group contains various low memory conditions." ::= { lgpConditionsWellKnown 160 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.476.1.42.3.2.1.160.1 | lgpConditionLowMemory1 | 0 | 0 | The system has detected a low memory condition. The control board is low in memory resources. |
To many brothers! Only 100 nearest brothers are shown.
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
... | ||||
1.3.6.1.4.1.476.1.42.3.2.1.110 | lgpConditionParallelSysLoadShareFault | 0 | 0 | The parallel system has detected a load share fault condition. |
1.3.6.1.4.1.476.1.42.3.2.1.111 | lgpConditionBatteryFault | 0 | 0 | The system has detected a battery fault condition. The battery conductors are either reversed or disconnected. |
1.3.6.1.4.1.476.1.42.3.2.1.112 | lgpConditionBatteryConverterFailure | 0 | 0 | The system has detected a battery converter failure condition. |
1.3.6.1.4.1.476.1.42.3.2.1.113 | lgpConditionBatteryBalancerFault | 0 | 0 | The system has detected a battery balancer fault condition. |
1.3.6.1.4.1.476.1.42.3.2.1.114 | lgpConditionpsUpsOperationFault | 0 | 0 | The system has detected an operation fault. The UPS attempted to transfer to maintenance bypass without following the proper se… |
1.3.6.1.4.1.476.1.42.3.2.1.115 | lgpConditionOutputToLoadOnJointMode | 0 | 0 | The system load is being supported by both the battery and rectifier. |
1.3.6.1.4.1.476.1.42.3.2.1.116 | lgpConditionInputNeutralLost | 0 | 0 | The system had detected the main input neutral is disconnected. |
1.3.6.1.4.1.476.1.42.3.2.1.117 | lgpConditionLowBatteryWarning | 0 | 0 | The battery's remaining charge is less than or equal to the configured low threshold. |
1.3.6.1.4.1.476.1.42.3.2.1.118 | lgpConditionInternalFault | 0 | 0 | The system has detected an internal fault. |
1.3.6.1.4.1.476.1.42.3.2.1.119 | lgpConditionBatteryTestFailed | 0 | 0 | The system has detected a battery self-test failure. |
1.3.6.1.4.1.476.1.42.3.2.1.120 | lgpConditionPowerModuleWarning | 0 | 0 | The system has detected an alarm condition on one, or more, power modules. |
1.3.6.1.4.1.476.1.42.3.2.1.121 | lgpConditionBatteryModuleWarning | 0 | 0 | The system has detected an alarm condition on one, or more, battery modules. |
1.3.6.1.4.1.476.1.42.3.2.1.122 | lgpConditionControlModuleWarning | 0 | 0 | The system has detected a control module warning. |
1.3.6.1.4.1.476.1.42.3.2.1.123 | lgpConditionUpsOperationFault | 0 | 0 | The system has detected an operation fault. The UPS attempted to transfer to maintenance bypass without following the proper se… |
1.3.6.1.4.1.476.1.42.3.2.1.124 | lgpConditionActiveAlarm | 0 | 0 | The system has detected an alarm condition. |
1.3.6.1.4.1.476.1.42.3.2.1.125 | lgpConditionRectifierCommunicationFailure | 0 | 0 | The system has detected an internal communication failure condition with the rectifier. |
1.3.6.1.4.1.476.1.42.3.2.1.126 | lgpConditionInverterCommunicationFailure | 0 | 0 | The system has detected an internal communication failure condition with the inverter. |
1.3.6.1.4.1.476.1.42.3.2.1.127 | lgpConditionParallelSysConnectionFault | 0 | 0 | The parallel system has detected a connection fault. One or more of the devices are not properly connected. |
1.3.6.1.4.1.476.1.42.3.2.1.128 | lgpConditionParallelSysCommunicationFailure | 0 | 0 | The parallel system has detected a communication failure. |
1.3.6.1.4.1.476.1.42.3.2.1.129 | lgpConditionLostBatteryRedundancy | 0 | 0 | The system has detected the number of redundant battery modules has fallen below the configured redundant battery module thresho… |
1.3.6.1.4.1.476.1.42.3.2.1.130 | lgpConditionCompPumpDownFailure | 2 | 2 | The system has detected that a compressor has failed to pump down. |
1.3.6.1.4.1.476.1.42.3.2.1.131 | lgpConditionChilledWaterLowWaterFlow | 0 | 0 | The system has detected a chilled water low water flow condition. |
1.3.6.1.4.1.476.1.42.3.2.1.132 | lgpConditionAirFilterClogged | 0 | 0 | The system has detected a air filter clogged condition. |
1.3.6.1.4.1.476.1.42.3.2.1.133 | lgpConditionHumidifierFailure | 0 | 0 | The system has detected a humidifier failure condition. |
1.3.6.1.4.1.476.1.42.3.2.1.134 | lgpConditionRunHoursExceeded | 11 | 11 | The system has detected a pre-determined run hours threshold has been exceeded. |
1.3.6.1.4.1.476.1.42.3.2.1.135 | lgpConditionCommWarning | 16 | 16 | The system has detected a loss of communications with another module. |
1.3.6.1.4.1.476.1.42.3.2.1.136 | lgpConditionUnitOn | 0 | 0 | The unit is on. |
1.3.6.1.4.1.476.1.42.3.2.1.137 | lgpConditionUnitOff | 0 | 0 | The unit is off. |
1.3.6.1.4.1.476.1.42.3.2.1.138 | lgpConditionSleepModeOff | 0 | 0 | The system sleep mode operation has been turned off. |
1.3.6.1.4.1.476.1.42.3.2.1.139 | lgpConditionPowerOn | 0 | 0 | The system power is on. |
1.3.6.1.4.1.476.1.42.3.2.1.140 | lgpConditionSystemOnStanby | 0 | 0 | The system is on standby. |
1.3.6.1.4.1.476.1.42.3.2.1.141 | lgpConditionPowerOff | 0 | 0 | The system power is off. |
1.3.6.1.4.1.476.1.42.3.2.1.142 | lgpConditionHighTemperatureGroup | 5 | 5 | lgpConditionHightemperatureGroup |
1.3.6.1.4.1.476.1.42.3.2.1.143 | lgpConditionLowTemperatureGroup | 2 | 2 | The system has detected a low temperature condition. This group contains various low temperature conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.144 | lgpConditionHighHumidityGroup | 1 | 1 | The system has detected a high humidity condition. This group contains various high humidity conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.145 | lgpConditionLowHumidityGroup | 1 | 1 | The system has detected a low humidity condition. This group contains various high humidity conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.146 | lgpConditionPeerNetworkNoMaster | 0 | 0 | The system is unable to communicate with the master on the peer to peer network. |
1.3.6.1.4.1.476.1.42.3.2.1.147 | lgpConditionNoOnOffPermissions | 0 | 0 | The system lacks the permissions to execute the on/off operation. |
1.3.6.1.4.1.476.1.42.3.2.1.148 | lgpConditionPeerNetworkFailure | 0 | 0 | The system has detected a communication failure on the peer to peer network. |
1.3.6.1.4.1.476.1.42.3.2.1.149 | lgpConditionUnitDisabled | 0 | 0 | The unit is disabled. |
1.3.6.1.4.1.476.1.42.3.2.1.150 | lgpConditionUnitShutdown | 0 | 0 | The system has shutdown. |
1.3.6.1.4.1.476.1.42.3.2.1.151 | lgpConditionPeerNetworkDiscovered | 0 | 0 | The system has established communications on the peer to peer network. |
1.3.6.1.4.1.476.1.42.3.2.1.152 | lgpConditionLossOfWaterFlow | 0 | 0 | The system has detected a loss of water flow condition. |
1.3.6.1.4.1.476.1.42.3.2.1.153 | lgpConditionCondensatePumpHighWater | 0 | 0 | The system has detected high water in the condensate pump. |
1.3.6.1.4.1.476.1.42.3.2.1.154 | lgpConditionGeneralAlarm | 0 | 0 | The system has detected a general alarm condition. |
1.3.6.1.4.1.476.1.42.3.2.1.155 | lgpConditionProductSpecific | 0 | 0 | The system has detected a product specific condition. This condition is not currently available via the agent card. |
1.3.6.1.4.1.476.1.42.3.2.1.156 | lgpConditionReheatLockout | 0 | 0 | The system has locked out the electrical reheat operation for a specified amount of time. |
1.3.6.1.4.1.476.1.42.3.2.1.157 | lgpConditionHumidifierLockout | 0 | 0 | The system has locked out the humidifier operation for a specified amount of time. |
1.3.6.1.4.1.476.1.42.3.2.1.158 | lgpConditionCompressorsLockout | 0 | 0 | The system has locked out compressor operation for a specified amount of time. |
1.3.6.1.4.1.476.1.42.3.2.1.159 | lgpConditionCallService | 0 | 0 | The system has detected a condition that requires a service representative be contacted. |
1.3.6.1.4.1.476.1.42.3.2.1.161 | lgpConditionMemoryFailureGroup | 2 | 2 | This group contains various memory device failure conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.162 | lgpConditionUnitCodeErrorGroup | 19 | 19 | This group contains various memory device failure conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.163 | lgpConditionHighExternalDewPoint | 0 | 0 | The system has detected a high external dew point condition. The room dew point has exceeded the specified threshold. |
1.3.6.1.4.1.476.1.42.3.2.1.164 | lgpConditionHcbDisconnected | 0 | 0 | The system has detected the humidifier control board is disconnected or not installed. |
1.3.6.1.4.1.476.1.42.3.2.1.165 | lgpConditionBmsResetTimerExpired | 0 | 0 | The BMS fan speed control reset counter has timed out. |
1.3.6.1.4.1.476.1.42.3.2.1.166 | lgpConditionAgentFirmwareCorrupt | 0 | 0 | The firmware update to the agent card has failed and the firmware is now corrupt. |
1.3.6.1.4.1.476.1.42.3.2.1.175 | lgpConditionSystemAccessGroup | 2 | 2 | This group contains various system access conditions. An examples is an open access panel. |
1.3.6.1.4.1.476.1.42.3.2.1.176 | lgpConditionsDamperFailure | 1 | 1 | This group contains various damper failure conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.177 | lgpConditionRemoteShutdown | 0 | 0 | A remote shutdown occurred. |
1.3.6.1.4.1.476.1.42.3.2.1.178 | lgpConditionFireAlarm | 0 | 0 | Fire Alarm. |
1.3.6.1.4.1.476.1.42.3.2.1.179 | lgpConditionHeatersOverheated | 0 | 0 | Heaters Overheated. |
1.3.6.1.4.1.476.1.42.3.2.1.180 | lgpConditionCondenserFailureGroup | 2 | 2 | This group contains condenser failure conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.181 | lgpConditionHumidifierCyclinderWorn | 0 | 0 | The system has detected the humidifier cylinder is worn. |
1.3.6.1.4.1.476.1.42.3.2.1.182 | lgpConditionUnderCurrent | 2 | 2 | The system has detected a low current condition. The current of one or more sources in the system has fallen below a threshold … |
1.3.6.1.4.1.476.1.42.3.2.1.183 | lgpConditionHeatRejectorGroup | 2 | 2 | This group contains failure conditions for the heat rejection unit. |
1.3.6.1.4.1.476.1.42.3.2.1.184 | lgpConditionFreeCoolLockout | 0 | 0 | The free cooling capability has been disabled. |
1.3.6.1.4.1.476.1.42.3.2.1.185 | lgpConditionWaterLeakSensorFailure | 0 | 0 | The sensor used to detect water leaks is not connected or has failed. |
1.3.6.1.4.1.476.1.42.3.2.1.186 | lgpConditionNoLoadDetectedWarning | 0 | 0 | There is no load detected on the output. This can be an indication that the output is being powered by an external bypass sourc… |
1.3.6.1.4.1.476.1.42.3.2.1.187 | lgpConditionFirmwareGroup | 1 | 1 | Grouping level for firmware related conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.188 | lgpConditionTestGroup | 1 | 1 | Objects in this group of conditions are related to testing or test events. This object is never active. |
1.3.6.1.4.1.476.1.42.3.2.1.190 | lgpConditionReceptacleBranchGroup | 2 | 2 | Grouping level for receptacle branch conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.192 | lgpConditionInputUnqualified | 0 | 0 | The input is not qualified to provide power to the system. This may be due to system input over-voltage, system input under-vol… |
1.3.6.1.4.1.476.1.42.3.2.1.193 | lgpConditionBypassUnavailable | 0 | 0 | This summary event is asserted when the bypass is not available. Possible causes include: Bypass Sync Error, Bypass Line Fail, B… |
1.3.6.1.4.1.476.1.42.3.2.1.194 | lgpConditionAutoTransferFailed | 0 | 0 | The system is failing to automatically transfer the load to the alternate source. |
1.3.6.1.4.1.476.1.42.3.2.1.195 | lgpConditionSBSUnavailable | 0 | 0 | A Static Bypass Switch (SBS) Failure has been detected. Possible causes include: SBS Phase Open, SBS SCR (Silicon Controlled Rec… |
1.3.6.1.4.1.476.1.42.3.2.1.196 | lgpConditionSBSOverload | 0 | 0 | On at least one phase of the static bypass switch (SBS), the power dissapation limit has been exceeded. |
1.3.6.1.4.1.476.1.42.3.2.1.197 | lgpConditionExcessPulseParallel | 0 | 0 | The system has performed too many pulse parallel operations within the specified time interval. A pulse parallel operation is a… |
1.3.6.1.4.1.476.1.42.3.2.1.198 | lgpConditionRemoteBypassSwitchOffExt | 0 | 0 | The static bypass switch is off due to the state of an external signal. |
1.3.6.1.4.1.476.1.42.3.2.1.199 | lgpConditionManTransferInhibited | 0 | 0 | Manual transfer from inverter to bypass is inhibited. Bypass is not qualified. |
1.3.6.1.4.1.476.1.42.3.2.1.200 | lgpConditionManReTransferInhibited | 0 | 0 | Manual retransfer from bypass to inverter is inhibited. |
1.3.6.1.4.1.476.1.42.3.2.1.201 | lgpConditionBatteryChargeError | 0 | 0 | The battery is not charging properly. Some reasons for this condition include, but are not limited to: battery charger failure, b… |
1.3.6.1.4.1.476.1.42.3.2.1.202 | lgpConditionBatteryAutoTestInhibited | 0 | 0 | Automatic (scheduled) battery tests are inhibited. |
1.3.6.1.4.1.476.1.42.3.2.1.203 | lgpConditionBatteryChargeReducedExt | 0 | 0 | A reduced battery charging algorithm is being used due to an external signal. |
1.3.6.1.4.1.476.1.42.3.2.1.204 | lgpConditionBatteryCapacityLow | 0 | 0 | The battery capacity is low. Some reasons for this condition include, but are not limited to: a battery is offline, the battery … |
1.3.6.1.4.1.476.1.42.3.2.1.205 | lgpConditionBatteryTempImbalance | 0 | 0 | The temperature difference between two batteries in the system exceeds the predefined threshold. |
1.3.6.1.4.1.476.1.42.3.2.1.206 | lgpConditionBatteryEqualize | 0 | 0 | The rectifier output voltage has been increased to equalize the battery voltage level. |
1.3.6.1.4.1.476.1.42.3.2.1.207 | lgpConditionBatteryChargeInhibitedExt | 0 | 0 | Battery charging is inhibited due to an external inhibit signal. |
1.3.6.1.4.1.476.1.42.3.2.1.208 | lgpConditionServiceExtBatteryMonitorGroup | 2 | 2 | This group contains battery monitor service conditions. |
1.3.6.1.4.1.476.1.42.3.2.1.209 | lgpConditionBatteryGroundFault | 0 | 0 | Battery system ground fault amperage exceeds the threshold. |
1.3.6.1.4.1.476.1.42.3.2.1.210 | lgpConditionBatteryLowShutdown | 0 | 0 | With the battery breaker closed, the battery voltage has dropped below the calculated End-Of-Discharge (EOD) limit. |
... |