Sets the minimum number of kilobytes of system memory
allocated to the serial interface.
Default
15
Notes
This value must be less than K Mem For Spool.
A 0 value does not turn off the spooling buffer for
the serial interface. If the value is set to 0, the
printer calculates the Min K Spool automatically at
initialization.
The printer must be restarted for changes to the Min K
Spool menu to take effect. You can either let the printer
restart automatically after you save the change and exit
the Configuration menu, or you can wait for the change
to take effect the next time you manually turn on the
printer.
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsSerBufferSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Sets the minimum number of kilobytes of system memory allocated to the serial interface. Default 15 Notes This value must be less than K Mem For Spool. A 0 value does not turn off the spooling buffer for the serial interface. If the value is set to 0, the printer calculates the Min K Spool automatically at initialization. The printer must be restarted for changes to the Min K Spool menu to take effect. You can either let the printer restart automatically after you save the change and exit the Configuration menu, or you can wait for the change to take effect the next time you manually turn on the printer." ::= { qmsSerial 104 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.480.1.160.100 | qmsSerPSProtocol | 0 | 0 | Sets the binary communications protocol (BCP) for communicating over a serial interface to a PostScript printer. Choices Normal: En… |
1.3.6.1.4.1.480.1.160.101 | qmsSerMode | 0 | 0 | Enables or disables the serial port. Choices Interactive: Establish two-way communication between the host and the printer. Noninte… |
1.3.6.1.4.1.480.1.160.102 | qmsSerEmulation | 0 | 0 | Sets the serial interface emulation. Choices PostScript, HPGL, HPPCL, HEXDUMP, LN03, QUIC2 CCITT, Line Printer, TIFF, CALS, CGM, E… |
1.3.6.1.4.1.480.1.160.103 | qmsSerPriority | 0 | 0 | Allows you to specify which jobs are printed first, according to the interface through which they are received, when jobs are re… |
1.3.6.1.4.1.480.1.160.111 | qmsSerEndDocumentMode | 0 | 0 | Enables (and identifies an end-of-job sequence) or disables data stream sensing for the end-of-document (EOD) command. Choices None… |
1.3.6.1.4.1.480.1.160.112 | qmsSerSpoolTimeout | 0 | 0 | Sets the number of seconds the interface waits for data from the host before terminating a spooled print job. Choices 0-99999 Defau… |
1.3.6.1.4.1.480.1.160.201 | qmsSerBaudRate | 0 | 0 | Sets the rate data is transmitted (bits per second) over the serial interface. Choices 300, 600, 1200, 2400, 4800, 9600, 19200, 38… |
1.3.6.1.4.1.480.1.160.202 | qmsSerParity | 0 | 0 | Sets the check bit used to identify data transmission errors. Choices: None, Odd, Even Default: None Note: The printer's parity setti… |
1.3.6.1.4.1.480.1.160.203 | qmsSerIgnoreParity | 0 | 0 | Specifies how the printer should handle parity errors. Choices Off: Ignore parity errors. The printer prints its best interpretati… |
1.3.6.1.4.1.480.1.160.204 | qmsSerRxSWFlow | 0 | 0 | Sets the software communication protocol used by the printer to control communication from the host computer. Choices ETX/ACK, Rob… |
1.3.6.1.4.1.480.1.160.205 | qmsSerTxSWFlow | 0 | 0 | Sets the software communication protocol used by the host computer to control communication with the printer. Choices ETX/ACK, Non… |
1.3.6.1.4.1.480.1.160.206 | qmsSerDataBits | 0 | 0 | Sets the number of data bits transmitted per character. Choices 5 Bits, 6 Bits, 7 Bits, 8 Bits Default 8 Bits |
1.3.6.1.4.1.480.1.160.207 | qmsSerStopBits | 0 | 0 | Sets the number of stop bits transmitted per character. Choices 1 Bit, 2 Bits, 1 1/2 Bits Default One Bit |
1.3.6.1.4.1.480.1.160.208 | qmsSerHwCTS | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.209 | qmsSerHwRTS | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.210 | qmsSerHwDTR | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default On Notes If the host uses hardware flow control, … |
1.3.6.1.4.1.480.1.160.211 | qmsSerHwDTRPOL | 0 | 0 | Controls the flow of data between the printer and the host. Choices Reverse, Normal Default Normal Notes If the host uses hardware fl… |
1.3.6.1.4.1.480.1.160.212 | qmsSerHwDSR | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.213 | qmsSerHwDSRPOL | 0 | 0 | Controls the flow of data between the printer and the host. Choices Reverse, Normal Default Normal Notes If the host uses hardware f… |