An option in the Operator Control menu allows you to 'chain' input-
bins (tray and cassettes) so that when the first inputbin empties, the
printer will automatically draw media from another inputbin with either
the same or any size and type of media (dependent on the choice
selected).
Choices
On: Switch to the next inputbin with the same size and
type of media when the default inputbin is empty.
Note: Make sure the two trays/cassettes use the
same size paper.
Off: Don't switch inputbins; use only the default
inputbin.
On Any: Switch to the next inputbin with any size and
type of media when the default inputbin is empty.
Default
On
Notes
Use the Operator 'qmsENGInputbin' OID to set the
default inputbin. Make sure that the two inputbins use
the same size media.
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsENGChainInputBins OBJECT-TYPE SYNTAX INTEGER { off(1), on(2), onAny(3) } ACCESS read-write STATUS mandatory DESCRIPTION "An option in the Operator Control menu allows you to 'chain' input- bins (tray and cassettes) so that when the first inputbin empties, the printer will automatically draw media from another inputbin with either the same or any size and type of media (dependent on the choice selected). Choices On: Switch to the next inputbin with the same size and type of media when the default inputbin is empty. Note: Make sure the two trays/cassettes use the same size paper. Off: Don't switch inputbins; use only the default inputbin. On Any: Switch to the next inputbin with any size and type of media when the default inputbin is empty. Default On Notes Use the Operator 'qmsENGInputbin' OID to set the default inputbin. Make sure that the two inputbins use the same size media." ::= { qmsEngine 1011 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.480.1.304.1 | qmsENGTopOffset | 0 | 0 | This option allows you to adjust the vertical placement of printed images. To check image alignment, print a standard status pag… |
| 1.3.6.1.4.1.480.1.304.2 | qmsENGLeftOffset | 0 | 0 | This option allows you to adjust the horizontal placement of printed images. To check image alignment, print a standard status pa… |
| 1.3.6.1.4.1.480.1.304.4 | qmsENGTopOffsetDuplex | 0 | 0 | This option allows you to adjust the duplex vertical placement of printed images. To check image alignment, print a standard sta… |
| 1.3.6.1.4.1.480.1.304.6 | qmsENGLeftOffsetDuplex | 0 | 0 | This option allows you to adjust the duplex horizontal placement of printed images. To check image alignment, print a standard st… |
| 1.3.6.1.4.1.480.1.304.8 | qmsENGResolution | 0 | 0 | This option sets the print engine's default resolution. Choices 300 dpi-300x300 dpi resolution 600 dpi-600x600 dpi resolution 1200 … |
| 1.3.6.1.4.1.480.1.304.11 | qmsENGDefaultPaper | 0 | 0 | Default Paper is used when the default media is requested but the default input bin is missing from the engine. There's no way t… |
| 1.3.6.1.4.1.480.1.304.12 | qmsENGDuplex | 0 | 0 | Current duplexing setting on printers for which the feature is supported. Choices Off: Prints simplex pages. Long Edge: … |
| 1.3.6.1.4.1.480.1.304.14 | qmsENGOrientation | 0 | 0 | While you can usually specify the orientation of a print job in your application, if you consistently use a certain media orient… |
| 1.3.6.1.4.1.480.1.304.15 | qmsENGInputbin | 0 | 0 | Default inputbin number. |
| 1.3.6.1.4.1.480.1.304.16 | qmsENGOutputbin | 0 | 0 | Default outputbin number. |
| 1.3.6.1.4.1.480.1.304.17 | qmsENGCollation | 0 | 0 | Collation is one of your printer's features. It is the printing of sets of multiple copies of a document in numeric order. Your … |
| 1.3.6.1.4.1.480.1.304.19 | qmsENGErrorRecovery | 0 | 0 | When a media jam or other similar error occurs, the printer can reprint the job starting from the page on which the jam occurred… |
| 1.3.6.1.4.1.480.1.304.20 | qmsENGManualTrayMedia | 0 | 0 | Need description and values. |
| 1.3.6.1.4.1.480.1.304.21 | qmsENGToneroutAction | 0 | 0 | You can configure the printer to stop or to continue printing when a TONER LOW ACT. error message is displayed in the message wi… |
| 1.3.6.1.4.1.480.1.304.23 | qmsENGLetterheadMode | 0 | 0 | This option appears only if the duplexing unit is installed on the printer. The letterhead option allows you to print both simple… |
| 1.3.6.1.4.1.480.1.304.24 | qmsENGManualFeedTimeout | 0 | 0 | This option allows you to set the amount of time the printer waits for paper to be inserted into the multipurpose tray before it… |
| 1.3.6.1.4.1.480.1.304.26 | qmsENGOffsetStacking | 0 | 0 | This option appears only if the printer is capable of offset stacking. Choices: Off - Stacking of each output set is aligned with… |
| 1.3.6.1.4.1.480.1.304.27 | qmsENGEnergyStar | 0 | 0 | The Energy Saver option specifies whether the printer changes to a low-power state (the engine remains on, but the fuser turns o… |
| 1.3.6.1.4.1.480.1.304.40 | qmsENGPageOrder | 0 | 0 | Need input on this....is this new? |
| 1.3.6.1.4.1.480.1.304.41 | qmsENGEnvelopeTrayMedia | 0 | 0 | The envelope feeder can be adjusted to accept different envelope sizes. See chapter 7, of the Options manual, the 'Selecting Env… |
| 1.3.6.1.4.1.480.1.304.42 | qmsENGDensity | 0 | 0 | The Toner Density option adjusts the density of the toner that is laid down on the paper. Note: See your Minolta-QMS documentation… |
| 1.3.6.1.4.1.480.1.304.43 | qmsENGColorModel | 0 | 0 | Use this option to select between full-color and monochrome printing. Choices Gray, CMY, RGB, CMYK |
| 1.3.6.1.4.1.480.1.304.44 | qmsENGColorSeparation | 0 | 0 | Use this option to turn color separation on or off. Choices On, Off Default Off |
| 1.3.6.1.4.1.480.1.304.45 | qmsENGUnderColor | 0 | 0 | Need input on this....is this new? |
| 1.3.6.1.4.1.480.1.304.48 | qmsENGQuality | 0 | 0 | The Print Quality option allows the printer to operate at a lower rate of toner consumption and extend the life of your toner ca… |
| 1.3.6.1.4.1.480.1.304.1000 | qmsENGConsumeNameMulti | 1 | 1 | A table of the engine's consumable names. |
| 1.3.6.1.4.1.480.1.304.1001 | qmsENGConsumeLevelMulti | 1 | 1 | A table of the engine's consumable levels. |
| 1.3.6.1.4.1.480.1.304.1002 | qmsENGConsumeMaxMulti | 1 | 1 | A table of the engine's consumable maximum levels. |
| 1.3.6.1.4.1.480.1.304.1003 | qmsENGConsumeUnitsMulti | 1 | 1 | A table of the engine's consumable units. |
| 1.3.6.1.4.1.480.1.304.1004 | qmsENGConsumeTypeMulti | 1 | 1 | A table of the engine's consumable types. |
| 1.3.6.1.4.1.480.1.304.1005 | qmsENGConsumeNote1Multi | 1 | 1 | A table of the first note applicable to each of the engines consumable. |
| 1.3.6.1.4.1.480.1.304.1006 | qmsENGConsumeNote2Multi | 1 | 1 | A table of the second note applicable to each of the engine's consumables. |
| 1.3.6.1.4.1.480.1.304.1007 | qmsENGConsumeIndexMulti | 1 | 1 | Index into OID table. |
| 1.3.6.1.4.1.480.1.304.1010 | qmsENGNumConsumables | 0 | 0 | Number of engine-related consumables that exist within the system. |
| 1.3.6.1.4.1.480.1.304.1012 | qmsENGChainOutputbinMulti | 1 | 1 | A table of the engine's default input chaining setting. |
| 1.3.6.1.4.1.480.1.304.1013 | qmsENGInputbinMediatypeMulti | 1 | 1 | A table of the engine's default media type setting. |
| 1.3.6.1.4.1.480.1.304.1014 | qmsENGChainInputbinMulti | 1 | 1 | A table of the engine's default input chaining setting. |
| 1.3.6.1.4.1.480.1.304.1015 | qmsENGStaplePosition | 0 | 0 | This option identifies the location of the staple when stapling is enabled. Choices Off, Front corner, Back corner, Center, Offset… |