This option allows you to adjust the duplex vertical placement of printed images.
To check image alignment, print a standard status page (Print Status
key). When the printer is placing images properly, the alignment angle
bar in the lower-left corner of the status page is 0.5''/12.7 mm from
the left and bottom edges of the page. If the angle bar is off, use the
Administration/Engine/Image Alignment option to align the image vertically
in pixel increments (1/300'' or 0.08 mm).
Note: Engine constraints may limit the accuracy of pixel alignment.
Choices
000-300 (0.00''-1.00'')
Default
100 (0.33''/.84 mm)
Notes
Values above 100 move the image down.
Values below 100 move the image up.
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsENGTopOffsetDuplex OBJECT-TYPE SYNTAX INTEGER (0..300) ACCESS read-write STATUS mandatory DESCRIPTION "This option allows you to adjust the duplex vertical placement of printed images. To check image alignment, print a standard status page (Print Status key). When the printer is placing images properly, the alignment angle bar in the lower-left corner of the status page is 0.5''/12.7 mm from the left and bottom edges of the page. If the angle bar is off, use the Administration/Engine/Image Alignment option to align the image vertically in pixel increments (1/300'' or 0.08 mm). Note: Engine constraints may limit the accuracy of pixel alignment. Choices 000-300 (0.00''-1.00'') Default 100 (0.33''/.84 mm) Notes Values above 100 move the image down. Values below 100 move the image up." ::= { qmsEngine 4 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.480.1.304.1 | qmsENGTopOffset | 0 | 0 | This option allows you to adjust the vertical placement of printed images. To check image alignment, print a standard status pag… |
| 1.3.6.1.4.1.480.1.304.2 | qmsENGLeftOffset | 0 | 0 | This option allows you to adjust the horizontal placement of printed images. To check image alignment, print a standard status pa… |
| 1.3.6.1.4.1.480.1.304.6 | qmsENGLeftOffsetDuplex | 0 | 0 | This option allows you to adjust the duplex horizontal placement of printed images. To check image alignment, print a standard st… |
| 1.3.6.1.4.1.480.1.304.8 | qmsENGResolution | 0 | 0 | This option sets the print engine's default resolution. Choices 300 dpi-300x300 dpi resolution 600 dpi-600x600 dpi resolution 1200 … |
| 1.3.6.1.4.1.480.1.304.11 | qmsENGDefaultPaper | 0 | 0 | Default Paper is used when the default media is requested but the default input bin is missing from the engine. There's no way t… |
| 1.3.6.1.4.1.480.1.304.12 | qmsENGDuplex | 0 | 0 | Current duplexing setting on printers for which the feature is supported. Choices Off: Prints simplex pages. Long Edge: … |
| 1.3.6.1.4.1.480.1.304.14 | qmsENGOrientation | 0 | 0 | While you can usually specify the orientation of a print job in your application, if you consistently use a certain media orient… |
| 1.3.6.1.4.1.480.1.304.15 | qmsENGInputbin | 0 | 0 | Default inputbin number. |
| 1.3.6.1.4.1.480.1.304.16 | qmsENGOutputbin | 0 | 0 | Default outputbin number. |
| 1.3.6.1.4.1.480.1.304.17 | qmsENGCollation | 0 | 0 | Collation is one of your printer's features. It is the printing of sets of multiple copies of a document in numeric order. Your … |
| 1.3.6.1.4.1.480.1.304.19 | qmsENGErrorRecovery | 0 | 0 | When a media jam or other similar error occurs, the printer can reprint the job starting from the page on which the jam occurred… |
| 1.3.6.1.4.1.480.1.304.20 | qmsENGManualTrayMedia | 0 | 0 | Need description and values. |
| 1.3.6.1.4.1.480.1.304.21 | qmsENGToneroutAction | 0 | 0 | You can configure the printer to stop or to continue printing when a TONER LOW ACT. error message is displayed in the message wi… |
| 1.3.6.1.4.1.480.1.304.23 | qmsENGLetterheadMode | 0 | 0 | This option appears only if the duplexing unit is installed on the printer. The letterhead option allows you to print both simple… |
| 1.3.6.1.4.1.480.1.304.24 | qmsENGManualFeedTimeout | 0 | 0 | This option allows you to set the amount of time the printer waits for paper to be inserted into the multipurpose tray before it… |
| 1.3.6.1.4.1.480.1.304.26 | qmsENGOffsetStacking | 0 | 0 | This option appears only if the printer is capable of offset stacking. Choices: Off - Stacking of each output set is aligned with… |
| 1.3.6.1.4.1.480.1.304.27 | qmsENGEnergyStar | 0 | 0 | The Energy Saver option specifies whether the printer changes to a low-power state (the engine remains on, but the fuser turns o… |
| 1.3.6.1.4.1.480.1.304.40 | qmsENGPageOrder | 0 | 0 | Need input on this....is this new? |
| 1.3.6.1.4.1.480.1.304.41 | qmsENGEnvelopeTrayMedia | 0 | 0 | The envelope feeder can be adjusted to accept different envelope sizes. See chapter 7, of the Options manual, the 'Selecting Env… |
| 1.3.6.1.4.1.480.1.304.42 | qmsENGDensity | 0 | 0 | The Toner Density option adjusts the density of the toner that is laid down on the paper. Note: See your Minolta-QMS documentation… |
| 1.3.6.1.4.1.480.1.304.43 | qmsENGColorModel | 0 | 0 | Use this option to select between full-color and monochrome printing. Choices Gray, CMY, RGB, CMYK |
| 1.3.6.1.4.1.480.1.304.44 | qmsENGColorSeparation | 0 | 0 | Use this option to turn color separation on or off. Choices On, Off Default Off |
| 1.3.6.1.4.1.480.1.304.45 | qmsENGUnderColor | 0 | 0 | Need input on this....is this new? |
| 1.3.6.1.4.1.480.1.304.48 | qmsENGQuality | 0 | 0 | The Print Quality option allows the printer to operate at a lower rate of toner consumption and extend the life of your toner ca… |
| 1.3.6.1.4.1.480.1.304.1000 | qmsENGConsumeNameMulti | 1 | 1 | A table of the engine's consumable names. |
| 1.3.6.1.4.1.480.1.304.1001 | qmsENGConsumeLevelMulti | 1 | 1 | A table of the engine's consumable levels. |
| 1.3.6.1.4.1.480.1.304.1002 | qmsENGConsumeMaxMulti | 1 | 1 | A table of the engine's consumable maximum levels. |
| 1.3.6.1.4.1.480.1.304.1003 | qmsENGConsumeUnitsMulti | 1 | 1 | A table of the engine's consumable units. |
| 1.3.6.1.4.1.480.1.304.1004 | qmsENGConsumeTypeMulti | 1 | 1 | A table of the engine's consumable types. |
| 1.3.6.1.4.1.480.1.304.1005 | qmsENGConsumeNote1Multi | 1 | 1 | A table of the first note applicable to each of the engines consumable. |
| 1.3.6.1.4.1.480.1.304.1006 | qmsENGConsumeNote2Multi | 1 | 1 | A table of the second note applicable to each of the engine's consumables. |
| 1.3.6.1.4.1.480.1.304.1007 | qmsENGConsumeIndexMulti | 1 | 1 | Index into OID table. |
| 1.3.6.1.4.1.480.1.304.1010 | qmsENGNumConsumables | 0 | 0 | Number of engine-related consumables that exist within the system. |
| 1.3.6.1.4.1.480.1.304.1011 | qmsENGChainInputBins | 0 | 0 | An option in the Operator Control menu allows you to 'chain' input- bins (tray and cassettes) so that when the first inputbin em… |
| 1.3.6.1.4.1.480.1.304.1012 | qmsENGChainOutputbinMulti | 1 | 1 | A table of the engine's default input chaining setting. |
| 1.3.6.1.4.1.480.1.304.1013 | qmsENGInputbinMediatypeMulti | 1 | 1 | A table of the engine's default media type setting. |
| 1.3.6.1.4.1.480.1.304.1014 | qmsENGChainInputbinMulti | 1 | 1 | A table of the engine's default input chaining setting. |
| 1.3.6.1.4.1.480.1.304.1015 | qmsENGStaplePosition | 0 | 0 | This option identifies the location of the staple when stapling is enabled. Choices Off, Front corner, Back corner, Center, Offset… |