The Print Quality option allows the printer to operate at a lower
rate of toner consumption and extend the life of your toner cartridges.
This option also allows you to enable other installed quality features.
Choices
Normal: Normal toner use.
Conserve Toner: Toner use is lowered.
Smooth(600dpi): Requires MultiRes board.
Fine Mode: Reduces chassis vibration during image processing.
Default
Normal
Notes
When Conserve Toner is selected the Toner Density
option can be adjusted for the best acceptable print
quality. Toner Density can be set from 1 to 15.
Smoothing alters the size and position of dots that lie
on the outer edges of an object by reducing the width of
the laser pulse to a fraction of the full pulse width. This
smooths jagged-edges in text, lines, and graphics and
generally improves their print quality.
Fine Mode reduces the media feed rate, allowing each sheet
to complete the image transfer process before the next sheet
is fed to the media path. This reduces chassis vibration
that occurs during paper movement to a minimum level during
image processing.
Note: When printing halftones, smoothing is not recommended
because it may introduce artifacts in the halftone or
scanned image. For better results if smoothing is
required for your documents in text and line art, use
the basic option for halftone types.
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsENGQuality OBJECT-TYPE SYNTAX INTEGER { normal(1), conserveToner(2), smooth600dpi(3), fineMode(5) } ACCESS read-write STATUS mandatory DESCRIPTION "The Print Quality option allows the printer to operate at a lower rate of toner consumption and extend the life of your toner cartridges. This option also allows you to enable other installed quality features. Choices Normal: Normal toner use. Conserve Toner: Toner use is lowered. Smooth(600dpi): Requires MultiRes board. Fine Mode: Reduces chassis vibration during image processing. Default Normal Notes When Conserve Toner is selected the Toner Density option can be adjusted for the best acceptable print quality. Toner Density can be set from 1 to 15. Smoothing alters the size and position of dots that lie on the outer edges of an object by reducing the width of the laser pulse to a fraction of the full pulse width. This smooths jagged-edges in text, lines, and graphics and generally improves their print quality. Fine Mode reduces the media feed rate, allowing each sheet to complete the image transfer process before the next sheet is fed to the media path. This reduces chassis vibration that occurs during paper movement to a minimum level during image processing. Note: When printing halftones, smoothing is not recommended because it may introduce artifacts in the halftone or scanned image. For better results if smoothing is required for your documents in text and line art, use the basic option for halftone types." ::= { qmsEngine 48 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.480.1.304.1 | qmsENGTopOffset | 0 | 0 | This option allows you to adjust the vertical placement of printed images. To check image alignment, print a standard status pag… |
1.3.6.1.4.1.480.1.304.2 | qmsENGLeftOffset | 0 | 0 | This option allows you to adjust the horizontal placement of printed images. To check image alignment, print a standard status pa… |
1.3.6.1.4.1.480.1.304.4 | qmsENGTopOffsetDuplex | 0 | 0 | This option allows you to adjust the duplex vertical placement of printed images. To check image alignment, print a standard sta… |
1.3.6.1.4.1.480.1.304.6 | qmsENGLeftOffsetDuplex | 0 | 0 | This option allows you to adjust the duplex horizontal placement of printed images. To check image alignment, print a standard st… |
1.3.6.1.4.1.480.1.304.8 | qmsENGResolution | 0 | 0 | This option sets the print engine's default resolution. Choices 300 dpi-300x300 dpi resolution 600 dpi-600x600 dpi resolution 1200 … |
1.3.6.1.4.1.480.1.304.11 | qmsENGDefaultPaper | 0 | 0 | Default Paper is used when the default media is requested but the default input bin is missing from the engine. There's no way t… |
1.3.6.1.4.1.480.1.304.12 | qmsENGDuplex | 0 | 0 | Current duplexing setting on printers for which the feature is supported. Choices Off: Prints simplex pages. Long Edge: … |
1.3.6.1.4.1.480.1.304.14 | qmsENGOrientation | 0 | 0 | While you can usually specify the orientation of a print job in your application, if you consistently use a certain media orient… |
1.3.6.1.4.1.480.1.304.15 | qmsENGInputbin | 0 | 0 | Default inputbin number. |
1.3.6.1.4.1.480.1.304.16 | qmsENGOutputbin | 0 | 0 | Default outputbin number. |
1.3.6.1.4.1.480.1.304.17 | qmsENGCollation | 0 | 0 | Collation is one of your printer's features. It is the printing of sets of multiple copies of a document in numeric order. Your … |
1.3.6.1.4.1.480.1.304.19 | qmsENGErrorRecovery | 0 | 0 | When a media jam or other similar error occurs, the printer can reprint the job starting from the page on which the jam occurred… |
1.3.6.1.4.1.480.1.304.20 | qmsENGManualTrayMedia | 0 | 0 | Need description and values. |
1.3.6.1.4.1.480.1.304.21 | qmsENGToneroutAction | 0 | 0 | You can configure the printer to stop or to continue printing when a TONER LOW ACT. error message is displayed in the message wi… |
1.3.6.1.4.1.480.1.304.23 | qmsENGLetterheadMode | 0 | 0 | This option appears only if the duplexing unit is installed on the printer. The letterhead option allows you to print both simple… |
1.3.6.1.4.1.480.1.304.24 | qmsENGManualFeedTimeout | 0 | 0 | This option allows you to set the amount of time the printer waits for paper to be inserted into the multipurpose tray before it… |
1.3.6.1.4.1.480.1.304.26 | qmsENGOffsetStacking | 0 | 0 | This option appears only if the printer is capable of offset stacking. Choices: Off - Stacking of each output set is aligned with… |
1.3.6.1.4.1.480.1.304.27 | qmsENGEnergyStar | 0 | 0 | The Energy Saver option specifies whether the printer changes to a low-power state (the engine remains on, but the fuser turns o… |
1.3.6.1.4.1.480.1.304.40 | qmsENGPageOrder | 0 | 0 | Need input on this....is this new? |
1.3.6.1.4.1.480.1.304.41 | qmsENGEnvelopeTrayMedia | 0 | 0 | The envelope feeder can be adjusted to accept different envelope sizes. See chapter 7, of the Options manual, the 'Selecting Env… |
1.3.6.1.4.1.480.1.304.42 | qmsENGDensity | 0 | 0 | The Toner Density option adjusts the density of the toner that is laid down on the paper. Note: See your Minolta-QMS documentation… |
1.3.6.1.4.1.480.1.304.43 | qmsENGColorModel | 0 | 0 | Use this option to select between full-color and monochrome printing. Choices Gray, CMY, RGB, CMYK |
1.3.6.1.4.1.480.1.304.44 | qmsENGColorSeparation | 0 | 0 | Use this option to turn color separation on or off. Choices On, Off Default Off |
1.3.6.1.4.1.480.1.304.45 | qmsENGUnderColor | 0 | 0 | Need input on this....is this new? |
1.3.6.1.4.1.480.1.304.1000 | qmsENGConsumeNameMulti | 1 | 1 | A table of the engine's consumable names. |
1.3.6.1.4.1.480.1.304.1001 | qmsENGConsumeLevelMulti | 1 | 1 | A table of the engine's consumable levels. |
1.3.6.1.4.1.480.1.304.1002 | qmsENGConsumeMaxMulti | 1 | 1 | A table of the engine's consumable maximum levels. |
1.3.6.1.4.1.480.1.304.1003 | qmsENGConsumeUnitsMulti | 1 | 1 | A table of the engine's consumable units. |
1.3.6.1.4.1.480.1.304.1004 | qmsENGConsumeTypeMulti | 1 | 1 | A table of the engine's consumable types. |
1.3.6.1.4.1.480.1.304.1005 | qmsENGConsumeNote1Multi | 1 | 1 | A table of the first note applicable to each of the engines consumable. |
1.3.6.1.4.1.480.1.304.1006 | qmsENGConsumeNote2Multi | 1 | 1 | A table of the second note applicable to each of the engine's consumables. |
1.3.6.1.4.1.480.1.304.1007 | qmsENGConsumeIndexMulti | 1 | 1 | Index into OID table. |
1.3.6.1.4.1.480.1.304.1010 | qmsENGNumConsumables | 0 | 0 | Number of engine-related consumables that exist within the system. |
1.3.6.1.4.1.480.1.304.1011 | qmsENGChainInputBins | 0 | 0 | An option in the Operator Control menu allows you to 'chain' input- bins (tray and cassettes) so that when the first inputbin em… |
1.3.6.1.4.1.480.1.304.1012 | qmsENGChainOutputbinMulti | 1 | 1 | A table of the engine's default input chaining setting. |
1.3.6.1.4.1.480.1.304.1013 | qmsENGInputbinMediatypeMulti | 1 | 1 | A table of the engine's default media type setting. |
1.3.6.1.4.1.480.1.304.1014 | qmsENGChainInputbinMulti | 1 | 1 | A table of the engine's default input chaining setting. |
1.3.6.1.4.1.480.1.304.1015 | qmsENGStaplePosition | 0 | 0 | This option identifies the location of the staple when stapling is enabled. Choices Off, Front corner, Back corner, Center, Offset… |