This attribute specifies the type of Vc call:
switched,
permanentMaster,
permanentSlave,
permanentSlaveWithBackup,
permanentBackupSlave.
If the value of this attribute is set to switched then the remote end
must also be provisioned as switched. No information at the remote
end is defined about this switched interface.
If the value is set to permanentMaster, then a permanent
connection will be established between 2 ends. The remote end
must be defined as a permanentSlave, permanentBackupSlave or
permanentSlaveWithBackup. The connection cannot be established
if the remote end is defined as anything else. The end defined as
permanentMaster always initiates the calls. It will attempt to call
once per minute.
If the value is set to permanentSlave then a permanent connection
will be established between 2 ends. The remote end must be defined
as a permanentMaster. The connection cannot be established if the
remote end is defined as anything else. The permanentSlave end
will attempt to call once per minute.
If the value is set to permanentSlaveWithBackup then a permanent
connection will be established between the two ends. The remote
end must be defined as a permanentMaster. The connection cannot
be established if the remote interface end is defined as anything
else. The permanentSlaveWithBackup end will attempt to call once
per minute. When type is set to permanentSlaveWithBackup
connection will be cleared if interface becomes unavailable. This
enables a retry of the connection which can be redirected to
permanentBackupSlave.
If the value is set to permanentBackupSlave then a permanent
connection will be established between the 2 ends only if the
permanentMaster end is disconnected from the
permanentSlaveWithBackup end and a backup call is established
by the redirection system. If the permanentSlaveWithBackup
interface becomes available again, the permanentBackupSlave end
is disconnected and the permanentSlaveWithBackup end is
reconnected to the permanentMaster end. The
permanentBackupSlave end does not try to establish pvc call.
Parsed from file nortelPP-vcTesterV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-VcTesterMIB
This attribute specifies the type of Vc call:
switched,
permanentMaster,
permanentSlave,
permanentSlaveWithBackup,
permanentBackupSlave.
If the value of this attribute is set to switched then the remote end
must also be provisioned as switched. No information at the remote
end is defined about this switched interface.
If the value is set to permanentMaster, then a permanent
connection will be established between 2 ends. The remote end
must be defined as a permanentSlave, permanentBackupSlave or
permanentSlaveWithBackup. The connection cannot be established
if the remote end is defined as anything else. The end defined as
permanentMaster always initiates the calls. It will attempt to call
once per minute.
If the value is set to permanentSlave then a permanent connection
will be established between 2 ends. The remote end must be defined
as a permanentMaster. The connection cannot be established if the
remote end is defined as anything else. The permanentSlave end
will attempt to call once per minute.
If the value is set to permanentSlaveWithBackup then a permanent
connection will be established between the two ends. The remote
end must be defined as a permanentMaster. The connection cannot
be established if the remote interface end is defined as anything
else. The permanentSlaveWithBackup end will attempt to call once
per minute. When type is set to permanentSlaveWithBackup
connection will be cleared if interface becomes unavailable. This
enables a retry of the connection which can be redirected to
permanentBackupSlave.
If the value is set to permanentBackupSlave then a permanent
connection will be established between the 2 ends only if the
permanentMaster end is disconnected from the
permanentSlaveWithBackup end and a backup call is established
by the redirection system. If the permanentSlaveWithBackup
interface becomes available again, the permanentBackupSlave end
is disconnected and the permanentSlaveWithBackup end is
reconnected to the permanentMaster end. The
permanentBackupSlave end does not try to establish pvc call.
Parsed from file Nortel-Magellan-Passport-VcTesterMIB.mib
Module: Nortel-Magellan-Passport-VcTesterMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-VcTesterMIB
[Automatically extracted from oidview.com]
vctDcType OBJECT-TYPE SYNTAX INTEGER { switched(0), permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of Vc call: switched, permanentMaster, permanentSlave, permanentSlaveWithBackup, permanentBackupSlave. If the value of this attribute is set to switched then the remote end must also be provisioned as switched. No information at the remote end is defined about this switched interface. If the value is set to permanentMaster, then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentSlave, permanentBackupSlave or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It will attempt to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end will attempt to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface end is defined as anything else. The permanentSlaveWithBackup end will attempt to call once per minute. When type is set to permanentSlaveWithBackup connection will be cleared if interface becomes unavailable. This enables a retry of the connection which can be redirected to permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection will be established between the 2 ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the redirection system. If the permanentSlaveWithBackup interface becomes available again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish pvc call." DEFVAL { switched } ::= { vctDcOptionsEntry 6 }
vctDcType OBJECT-TYPE SYNTAX INTEGER { switched(0), permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of Vc call: switched, permanentMaster, permanentSlave, permanentSlaveWithBackup, permanentBackupSlave. If the value of this attribute is set to switched then the remote end must also be provisioned as switched. No information at the remote end is defined about this switched interface. If the value is set to permanentMaster, then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentSlave, permanentBackupSlave or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It will attempt to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end will attempt to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface end is defined as anything else. The permanentSlaveWithBackup end will attempt to call once per minute. When type is set to permanentSlaveWithBackup connection will be cleared if interface becomes unavailable. This enables a retry of the connection which can be redirected to permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection will be established between the 2 ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the redirection system. If the permanentSlaveWithBackup interface becomes available again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish pvc call." DEFVAL { switched } ::= { vctDcOptionsEntry 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.1 | vctDcLocalNpi | 0 | 0 | This attribute specifies the Numbering Plan Indicator (NPI) of the localDna. |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.2 | vctDcLocalDna | 0 | 0 | This attribute specifies the Data Network Address (Dna) of the local DTE. This address is used in formatting of call request to r… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.3 | vctDcRemoteNpi | 0 | 0 | Remote numbering Plan Indicator (Npi) indicates the numbering plan used in the remoteDna. |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.4 | vctDcRemoteDna | 0 | 0 | This attribute specifies the Data Network Address (Dna) of the remote. This is the called (destination) DTE address (Dna) to whi… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.5 | vctDcRemoteLcn | 0 | 0 | This attribute provides the remote LCN (Logical Channel Number) - it is used only for PVCs, where attribute type is set to perman… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.7 | vctDcSvcAutoCallRetry | 0 | 0 | svcAutoCallRetry is used only for switched calls, in which case the attribute type is set to switched. Otherwise, this attribute… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.8 | vctDcUserData | 0 | 0 | This attribute contains the user data, if present. userData is a 0 to 16 length string which is appended to the call request pac… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.10 | vctDcDiscardPriority | 0 | 0 | This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning val… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.11 | vctDcDataPath | 0 | 0 | This attribute specifies the data path to be used by Virtual Circuits on this interface. The value of the dataPath attribute in … |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.13 | vctDcCugIndex | 0 | 0 | This attribute specifies the CUG index which is to be signalled in PVC call requests to the remote end. The type of CUG signalli… |
| 1.3.6.1.4.1.562.2.4.1.5130.3.10.1.14 | vctDcCugType | 0 | 0 | This attribute specifies the type of CUG signalling to be used in PVC call request. Index of CUG to be used is defined in attrib… |