This attribute has been obsoleted and migrated under the NrtVbr
subcomponent. In addition, the type and range of new attribute has
been changed.
This attribute specifies the tolerable cell loss ratio (CLR) for nrt-
VBR traffic. The number is the logarithm (base 10) of the CLR. In
other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = -
10.This number must be greater than or equal to
vbrRtCellLossRatio since rt-VBR traffic has a higher discard
priority. The vbrNrtCellLossRatio is used by the Connection
Admission Control (CAC) algorithm to compute the required
(equivalent) cell rate for nrt-VBR connections.
There is a trade-off between the service category CLR and the
achievable link utilization. To guarantee an excellent service
category, the CLR should be as small as possible (e.g., 1E-10).
However, a smaller CLR results in a larger equivalent cell rate for a
given connection and hence a lower link utilization.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute has been obsoleted and migrated under the NrtVbr
subcomponent. In addition, the type and range of new attribute has
been changed.
This attribute specifies the tolerable cell loss ratio (CLR) for nrt-
VBR traffic. The number is the logarithm (base 10) of the CLR. In
other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = -
10.This number must be greater than or equal to
vbrRtCellLossRatio since rt-VBR traffic has a higher discard
priority. The vbrNrtCellLossRatio is used by the Connection
Admission Control (CAC) algorithm to compute the required
(equivalent) cell rate for nrt-VBR connections.
There is a trade-off between the service category CLR and the
achievable link utilization. To guarantee an excellent service
category, the CLR should be as small as possible (e.g., 1E-10).
However, a smaller CLR results in a larger equivalent cell rate for a
given connection and hence a lower link utilization.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCAVbrNrtCellLossRatio OBJECT-TYPE SYNTAX INTEGER (-10..0) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute has been obsoleted and migrated under the NrtVbr subcomponent. In addition, the type and range of new attribute has been changed. This attribute specifies the tolerable cell loss ratio (CLR) for nrt- VBR traffic. The number is the logarithm (base 10) of the CLR. In other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = - 10.This number must be greater than or equal to vbrRtCellLossRatio since rt-VBR traffic has a higher discard priority. The vbrNrtCellLossRatio is used by the Connection Admission Control (CAC) algorithm to compute the required (equivalent) cell rate for nrt-VBR connections. There is a trade-off between the service category CLR and the achievable link utilization. To guarantee an excellent service category, the CLR should be as small as possible (e.g., 1E-10). However, a smaller CLR results in a larger equivalent cell rate for a given connection and hence a lower link utilization." DEFVAL { -7 } ::= { mscAtmIfCAProvEntry 110 }
mscAtmIfCAVbrNrtCellLossRatio OBJECT-TYPE SYNTAX INTEGER (-10..0) ACCESS read-write STATUS obsolete DESCRIPTION "This attribute has been obsoleted and migrated under the NrtVbr subcomponent. In addition, the type and range of new attribute has been changed. This attribute specifies the tolerable cell loss ratio (CLR) for nrt- VBR traffic. The number is the logarithm (base 10) of the CLR. In other words if the target CLR = 1E-10 then vbrNrtCellLossRatio = - 10.This number must be greater than or equal to vbrRtCellLossRatio since rt-VBR traffic has a higher discard priority. The vbrNrtCellLossRatio is used by the Connection Admission Control (CAC) algorithm to compute the required (equivalent) cell rate for nrt-VBR connections. There is a trade-off between the service category CLR and the achievable link utilization. To guarantee an excellent service category, the CLR should be as small as possible (e.g., 1E-10). However, a smaller CLR results in a larger equivalent cell rate for a given connection and hence a lower link utilization." DEFVAL { -7 } ::= { mscAtmIfCAProvEntry 110 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.5 | mscAtmIfCAMaxVpcs | 0 | 0 | This attribute specifies the maximum number of Vpcs that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.6 | mscAtmIfCAMaxVccs | 0 | 0 | This attribute specifies the maximum number of usable Vccs (and Vpt Vccs) that can be configured on this AtmIf. The value must n… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.7 | mscAtmIfCAMinMulticastBranches | 0 | 0 | This attribute specifies the guaranteed number of switched multicast branches that can be activated on this AtmIf, including tho… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.8 | mscAtmIfCAMaxMulticastBranches | 0 | 0 | This attribute specifies the maximum number of provisionable multicast branches that can be activated on this AtmIf, including th… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.9 | mscAtmIfCAMaxVpts | 0 | 0 | This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.10 | mscAtmIfCAMinAutoSelectedVci | 0 | 0 | This attribute specifies the default lower boundary for VCIs which are automatically allocated for a switched Vcc. A VCI number … |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.15 | mscAtmIfCAMinAutoSelectedVciForVpiZero | 0 | 0 | This attribute specifies the minimum VCI value which is automatically allocated for a switched Vcc with VPI value of zero. A VCI … |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.20 | mscAtmIfCAMinAutoSelectedVciForNonZeroVpi | 0 | 0 | This attribute specifies the minimum VCI value which is automatically allocated for a switched Vcc with a non-zero VPI value. A V… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.25 | mscAtmIfCAPermittedSvcAtmServiceCategories | 0 | 0 | This attribute specifies which ATM service categories are permitted on this interface for SVCs. The value of this attribute does… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.30 | mscAtmIfCACbrPool | 0 | 0 | This attribute has been obsoleted and migrated under the Cbr subcomponent. In addition, notApplicable is no longer a valid value… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.40 | mscAtmIfCACbrCdvt | 0 | 0 | This attribute has been obsoleted and migrated under the Cbr subcomponent. This attribute specifies the cell delay variation tole… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.50 | mscAtmIfCACbrCellLossRatio | 0 | 0 | This attribute has been obsoleted and migrated under the Cbr subcomponent. In addition, the type and range of the new attribute h… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.51 | mscAtmIfCASvcCbrHoldingPriority | 0 | 0 | This attribute has been obsoleted and migrated under the Cbr subcomponent. This attribute specifies the default holding priority … |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.52 | mscAtmIfCASvcVbrRtHoldingPriority | 0 | 0 | This attribute has been obsoleted and migrated under the RtVbr subcomponent. This attribute specifies the default holding priorit… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.53 | mscAtmIfCASvcVbrNrtHoldingPriority | 0 | 0 | This attribute has been obsoleted and migrated under the NrtVbr subcomponent. This attribute specifies the default holding priori… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.60 | mscAtmIfCAVbrRtPool | 0 | 0 | This attribute has been obsoleted and migrated under the RtVbr subcomponent. In addition, notApplicable is no longer a valid val… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.70 | mscAtmIfCAVbrRtCdvt | 0 | 0 | This attribute has been obsoleted and migrated under the RtVbr subcomponent. This attribute specifies the cell delay variation to… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.80 | mscAtmIfCAVbrRtCellLossRatio | 0 | 0 | This attribute has been obsoleted and migrated under the RtVbr subcomponent. In addition, the type and range of this attribute h… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.90 | mscAtmIfCAVbrNrtPool | 0 | 0 | This attribute has been obsoleted and migrated under the NrtVbr subcomponent. In addition, notApplicable is no longer a valid va… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.100 | mscAtmIfCAVbrNrtCdvt | 0 | 0 | This attribute has been obsoleted and migrated under the NrtVbr subcomponent. This attribute specifies the cell delay variation t… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.105 | mscAtmIfCAMaxCaVpcs | 0 | 0 | This attribute specifies the maximum number of Vpcs that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.106 | mscAtmIfCAMaxCaVpts | 0 | 0 | This attribute specifies the maximum number of Vpts that can be activated on this AtmIf. If the AtmIf is linked to a LogicalProc… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.120 | mscAtmIfCAUbrMaxConnections | 0 | 0 | This attribute is obsolete in P6.0, and has been migrated to the CA Ubr/0 maxVccs and maxVpcs attributes. This attribute specifi… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.121 | mscAtmIfCAMinAutoSelectedVpi | 0 | 0 | This attribute specifies the minimum VPI value which will be automatically allocated for a switched Vpc. A VPI number is automati… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.122 | mscAtmIfCAPermittedAtmServiceCategories | 0 | 0 | This attribute specifies which ATM service categories are permitted on this interface for SVPs and SVCs. The value of this attri… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.125 | mscAtmIfCAMaxAutoSelectedVpi | 0 | 0 | This attribute specifies the maximumVPI value which will be automatically allocated for a switched Vpc or Vcc. A VPI number is au… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.126 | mscAtmIfCAMaxAutoSelectedVciForVpiZero | 0 | 0 | This attribute specifies the maximum VCI value which is automatically allocated for a switched Vcc. A VCI number is automatically… |
| 1.3.6.1.4.1.562.36.2.1.114.3.100.1.127 | mscAtmIfCAMaxAutoSelectedVciForNonZeroVpi | 0 | 0 | This attribute specifies the maximum VCI value which is automatically allocated for a switched Vcc. A VCI number is automatically… |