The Forward Error Correction (FEC) correctable count
threshold. This object is applicable for profile 1.
A value 0 indicates to bypass the threshold check.
When CMTS detects that FEC correctable count goes
higher than ccsUpSpecMgmtFecCorrectThres1, it
switch to Profile 2. Therefore,
ccsUpSpecMgmtFecCorrectThres1 should be smaller
than ccsUpSpecMgmtFecCorrectThres2.
Parsed from file CISCO-CABLE-SPECTRUM-MIB.mib
Module: CISCO-CABLE-SPECTRUM-MIB
The Forward Error Correction (FEC) correctable count
threshold. This object is applicable for profile 1.
A value 0 indicates to bypass the threshold check.
When CMTS detects that FEC correctable count goes
higher than ccsUpSpecMgmtFecCorrectThres1, it
switch to Profile 2. Therefore,
ccsUpSpecMgmtFecCorrectThres1 should be smaller
than ccsUpSpecMgmtFecCorrectThres2.
The Forward Error Correction (FEC) correctable count
threshold. This object is applicable for profile 1.
A value 0 indicates to bypass the threshold check.
When CMTS detects that FEC correctable count goes
higher than ccsUpSpecMgmtFecCorrectThres1, it
switch to Profile 2. Therefore,
ccsUpSpecMgmtFecCorrectThres1 should be smaller
than ccsUpSpecMgmtFecCorrectThres2.
Parsed from file CISCO-CABLE-SPECTRUM-MIB.my.txt
Company: None
Module: CISCO-CABLE-SPECTRUM-MIB
The Forward Error Correction (FEC) correctable count
threshold. This object is applicable for profile 1.
A value 0 indicates to bypass the threshold check.
When CMTS detects that FEC correctable count goes
higher than ccsUpSpecMgmtFecCorrectThres1, it
switch to Profile 2. Therefore,
ccsUpSpecMgmtFecCorrectThres1 should be smaller
than ccsUpSpecMgmtFecCorrectThres2.
ccsUpSpecMgmtFecCorrectThres1 OBJECT-TYPE SYNTAX Integer32 (0 | 1..30 ) MAX-ACCESS read-write STATUS current DESCRIPTION "The Forward Error Correction (FEC) correctable count threshold. This object is applicable for profile 1. A value 0 indicates to bypass the threshold check. When CMTS detects that FEC correctable count goes higher than ccsUpSpecMgmtFecCorrectThres1, it switch to Profile 2. Therefore, ccsUpSpecMgmtFecCorrectThres1 should be smaller than ccsUpSpecMgmtFecCorrectThres2." ::= { ccsUpSpecMgmtEntry 4 }
ccsUpSpecMgmtFecCorrectThres1 OBJECT-TYPE SYNTAX INTEGER(0|1..30) ACCESS read-write STATUS mandatory DESCRIPTION "The Forward Error Correction (FEC) correctable count threshold. This object is applicable for profile 1. A value 0 indicates to bypass the threshold check. When CMTS detects that FEC correctable count goes higher than ccsUpSpecMgmtFecCorrectThres1, it switch to Profile 2. Therefore, ccsUpSpecMgmtFecCorrectThres1 should be smaller than ccsUpSpecMgmtFecCorrectThres2." ::= { ccsUpSpecMgmtEntry 4 }
Vendor: Cisco
Module: CISCO-CABLE-SPECTRUM-MIB
[Automatically extracted from oidview.com]
ccsUpSpecMgmtFecCorrectThres1 OBJECT-TYPE SYNTAX Integer32 (0 | 1..30 ) MAX-ACCESS read-write STATUS current DESCRIPTION "The Forward Error Correction (FEC) correctable count threshold. This object is applicable for profile 1. A value 0 indicates to bypass the threshold check. When CMTS detects that FEC correctable count goes higher than ccsUpSpecMgmtFecCorrectThres1, it switch to Profile 2. Therefore, ccsUpSpecMgmtFecCorrectThres1 should be smaller than ccsUpSpecMgmtFecCorrectThres2." ::= { ccsUpSpecMgmtEntry 4 }
ccsUpSpecMgmtFecCorrectThres1 OBJECT-TYPE SYNTAX Integer32 (0 | 1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "The Forward Error Correction (FEC) correctable count threshold. This object is applicable for profile 1. A value 0 indicates to bypass the threshold check. When CMTS detects that FEC correctable count goes higher than ccsUpSpecMgmtFecCorrectThres1, it switch to Profile 2. Therefore, ccsUpSpecMgmtFecCorrectThres1 should be smaller than ccsUpSpecMgmtFecCorrectThres2." ::= { ccsUpSpecMgmtEntry 4 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.114.1.3.1.1.1 | ccsUpSpecMgmtHopPriority | 0 | 0 | A preference priority for changing the frequency, modulation, or channel width supporting the automatic switching of the modulati… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.2 | ccsUpSpecMgmtSnrThres1 | 0 | 0 | The Signal to Noise (SNR) threshold. This object is applicable for modulation profile 1. When the CMTS detects that the SNR goes… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.3 | ccsUpSpecMgmtSnrThres2 | 0 | 0 | The Signal to Noise (SNR) threshold. This object is applicable for modulation profile 2. Refer to ccsUpSpecMgmtCriteria on how cc… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.5 | ccsUpSpecMgmtFecCorrectThres2 | 0 | 0 | The FEC correctable count threshold. This object is applicable for profile 2. When CMTS detects that FEC correctable count goes … |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.6 | ccsUpSpecMgmtFecUnCorrectThres1 | 0 | 0 | The FEC uncorrectable count threshold. This object is applicable for modulation profile 1. A value 0 indicates to bypass the thr… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.7 | ccsUpSpecMgmtFecUnCorrectThres2 | 0 | 0 | The FEC uncorrectable count threshold. This object is applicable for modulation profile 2. A value 0 indicates to bypass the thr… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.8 | ccsUpSpecMgmtSnrPollPeriod | 0 | 0 | A period between SNR pollings. The SNR is collected from the Fast Fourier Transform (FFT) measurement over the in-use band when t… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.9 | ccsUpSpecMgmtHopCondition | 0 | 0 | A condition that triggers hopping. The SNR condition occurs when SNR does not meet the ccsUpSpecMgmtSnrThres1 or ccsUpSpecMgmtSnr… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.10 | ccsUpSpecMgmtFromCenterFreq | 0 | 0 | Center frequency before hopping occurs. A value 0 indicates that the interface has no frequency assigned. |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.11 | ccsUpSpecMgmtToCenterFreq | 0 | 0 | Current center frequency. A value 0 indicates that the interface has no frequency assigned. |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.12 | ccsUpSpecMgmtFromBandWidth | 0 | 0 | Bandwidth before hopping occurs. |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.13 | ccsUpSpecMgmtToBandWidth | 0 | 0 | Current bandwidth. |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.14 | ccsUpSpecMgmtFromModProfile | 0 | 0 | Modulation profile index before hopping occurs. It is the index identical to the docsIfModIndex in the docsIfCmtsModulationTable.… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.15 | ccsUpSpecMgmtToModProfile | 0 | 0 | The current modulation profile index. It is the index identical to the docsIfModIndex in the docsIfCmtsModulationTable. For the de… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.16 | ccsUpSpecMgmtSNR | 0 | 0 | Current SNR. A value -99 indicates the system detected no modem on line, and a value of -100 indicates the system was unable to re… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.17 | ccsUpSpecMgmtUpperBoundFreq | 0 | 0 | Upper bound frequency that the upstream supports. |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.18 | ccsUpSpecMgmtCnrThres1 | 0 | 0 | The Carrier to Noise (CNR) threshold. This object is applicable for modulation profile 1. When the CMTS detects that the CNR goe… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.19 | ccsUpSpecMgmtCnrThres2 | 0 | 0 | The Carrier to Noise (CNR) threshold. This object is applicable for modulation profile 2. Refer to ccsUpSpecMgmtCriteria on how c… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.20 | ccsUpSpecMgmtCNR | 0 | 0 | Current CNR. A value -99 indicates the system detected no modem on line, and a value of -100 indicates the system was unable to re… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.21 | ccsUpSpecMgmtMissedMaintMsgThres | 0 | 0 | The missed maintenance message threshold in percentage. A value 0 indicates that the interface has no spectrum group assigned. i.… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.22 | ccsUpSpecMgmtHopPeriod | 0 | 0 | The minimum time between frequency hops in seconds. A value 0 indicates that the interface has no spectrum group assigned. i.e. c… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.23 | ccsUpSpecMgmtCriteria | 0 | 0 | Defines the criteria that trigger a change in frequency hopping, modulation or channel width. Depending on the type of linecards,… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.24 | ccsUpSpecMgmtSpecGroup | 0 | 0 | The spectrum group assigned to the upstream. The value of 0 for the object indicates that the upstream has no spectrum group assi… |
| 1.3.6.1.4.1.9.9.114.1.3.1.1.25 | ccsUpSpecMgmtSharedSpectrum | 0 | 0 | The fiber-node assigned to the upstreams. Upstreams having same fiber-node number indicates that they physically combine together… |