This object specifies the method defined to identify the
alternate port in the segment that takes part in VLAN load
balancing by blocking a subset of VLANs after preemption.
'none' - no method is specified to identify the alternate
port. In this case, the primary edge blocks all VLANs after
preemption.
'offset' - identification is done by a number which indicates
the offset of the port from an edge port.
'crepBlockPortNumInfo' defines the value.
'portId' - identification is done by the port identifier of
the port. 'crepBlockPortIdInfo' defines the value.
'prefFlag' - to select the port in the segment that is
configured as the preferred alternate port for VLAN load balancing.
While setting the value to 'offset' or 'portId', corresponding
values for the value defining objects (mentioned along with the
corresponding descriptions above) should also be provided, along with.
Additionally, at least one of objects that define the VLANs to
be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k,
crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with
a non-empty value, when setting the value to anything other than 'none'.
This value is only effective on the device acting as the REP
primary edge.
Parsed from file CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB.mib
Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
This object specifies the method defined to identify the
alternate port in the segment that takes part in VLAN load
balancing by blocking a subset of VLANs after preemption.
'none' - no method is specified to identify the alternate
port. In this case, the primary edge blocks all VLANs after
preemption.
'offset' - identification is done by a number which indicates
the offset of the port from an edge port.
'crepBlockPortNumInfo' defines the value.
'portId' - identification is done by the port identifier of
the port. 'crepBlockPortIdInfo' defines the value.
'prefFlag' - to select the port in the segment that is
configured as the preferred alternate port for VLAN load balancing.
While setting the value to 'offset' or 'portId', corresponding
values for the value defining objects (mentioned along with the
corresponding descriptions above) should also be provided, along with.
Additionally, at least one of objects that define the VLANs to
be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k,
crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with
a non-empty value, when setting the value to anything other than 'none'.
This value is only effective on the device acting as the REP
primary edge.
This object specifies the method defined to identify the
alternate port in the segment that takes part in VLAN load
balancing by blocking a subset of VLANs after preemption.
'none' - no method is specified to identify the alternate
port. In this case, the primary edge blocks all VLANs after
preemption.
'offset' - identification is done by a number which indicates
the offset of the port from an edge port.
'crepBlockPortNumInfo' defines the value.
'portId' - identification is done by the port identifier of
the port. 'crepBlockPortIdInfo' defines the value.
'prefFlag' - to select the port in the segment that is
configured as the preferred alternate port for VLAN load balancing.
While setting the value to 'offset' or 'portId', corresponding
values for the value defining objects (mentioned along with the
corresponding descriptions above) should also be provided, along with.
Additionally, at least one of objects that define the VLANs to
be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k,
crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with
a non-empty value, when setting the value to anything other than 'none'.
This value is only effective on the device acting as the REP
primary edge.
Parsed from file CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB.my.txt
Company: None
Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
This object specifies the method defined to identify the
alternate port in the segment that takes part in VLAN load
balancing by blocking a subset of VLANs after preemption.
'none' - no method is specified to identify the alternate
port. In this case, the primary edge blocks all VLANs after
preemption.
'offset' - identification is done by a number which indicates
the offset of the port from an edge port.
'crepBlockPortNumInfo' defines the value.
'portId' - identification is done by the port identifier of
the port. 'crepBlockPortIdInfo' defines the value.
'prefFlag' - to select the port in the segment that is
configured as the preferred alternate port for VLAN load balancing.
While setting the value to 'offset' or 'portId', corresponding
values for the value defining objects (mentioned along with the
corresponding descriptions above) should also be provided, along with.
Additionally, at least one of objects that define the VLANs to
be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k,
crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with
a non-empty value, when setting the value to anything other than 'none'.
This value is only effective on the device acting as the REP
primary edge.
crepLoadBalanceBlockPortType OBJECT-TYPE SYNTAX INTEGER { none(1), offset(2), portId(3), prefFlag(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs after preemption. 'none' - no method is specified to identify the alternate port. In this case, the primary edge blocks all VLANs after preemption. 'offset' - identification is done by a number which indicates the offset of the port from an edge port. 'crepBlockPortNumInfo' defines the value. 'portId' - identification is done by the port identifier of the port. 'crepBlockPortIdInfo' defines the value. 'prefFlag' - to select the port in the segment that is configured as the preferred alternate port for VLAN load balancing. While setting the value to 'offset' or 'portId', corresponding values for the value defining objects (mentioned along with the corresponding descriptions above) should also be provided, along with. Additionally, at least one of objects that define the VLANs to be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k, crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with a non-empty value, when setting the value to anything other than 'none'. This value is only effective on the device acting as the REP primary edge." DEFVAL { none } ::= { crepInterfaceConfigEntry 13 }
crepLoadBalanceBlockPortType OBJECT-TYPE SYNTAX INTEGER { none(1), offset(2), portId(3), prefFlag(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs after preemption. 'none' - no method is specified to identify the alternate port. In this case, the primary edge blocks all VLANs after preemption. 'offset' - identification is done by a number which indicates the offset of the port from an edge port. 'crepBlockPortNumInfo' defines the value. 'portId' - identification is done by the port identifier of the port. 'crepBlockPortIdInfo' defines the value. 'prefFlag' - to select the port in the segment that is configured as the preferred alternate port for VLAN load balancing. While setting the value to 'offset' or 'portId', corresponding values for the value defining objects (mentioned along with the corresponding descriptions above) should also be provided, along with. Additionally, at least one of objects that define the VLANs to be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k, crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with a non-empty value, when setting the value to anything other than 'none'. This value is only effective on the device acting as the REP primary edge." DEFVAL { none } ::= { crepInterfaceConfigEntry 13 }
Vendor: Cisco
Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
[Automatically extracted from oidview.com]
crepLoadBalanceBlockPortType OBJECT-TYPE SYNTAX INTEGER { none(1), offset(2), portId(3), prefFlag(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs after preemption. 'none' - no method is specified to identify the alternate port. In this case, the primary edge blocks all VLANs after preemption. 'offset' - identification is done by a number which indicates the offset of the port from an edge port. 'crepBlockPortNumInfo' defines the value. 'portId' - identification is done by the port identifier of the port. 'crepBlockPortIdInfo' defines the value. 'prefFlag' - to select the port in the segment that is configured as the preferred alternate port for VLAN load balancing. While setting the value to 'offset' or 'portId', corresponding values for the value defining objects (mentioned along with the corresponding descriptions above) should also be provided, along with. Additionally, at least one of objects that define the VLANs to be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k, crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with a non-empty value, when setting the value to anything other than 'none'. This value is only effective on the device acting as the REP primary edge." DEFVAL { none } ::= { crepInterfaceConfigEntry 13 }
crepLoadBalanceBlockPortType OBJECT-TYPE SYNTAX INTEGER { none(1), offset(2), portId(3), prefFlag(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs after preemption. 'none' - no method is specified to identify the alternate port. In this case, the primary edge blocks all VLANs after preemption. 'offset' - identification is done by a number which indicates the offset of the port from an edge port. 'crepBlockPortNumInfo' defines the value. 'portId' - identification is done by the port identifier of the port. 'crepBlockPortIdInfo' defines the value. 'prefFlag' - to select the port in the segment that is configured as the preferred alternate port for VLAN load balancing. While setting the value to 'offset' or 'portId', corresponding values for the value defining objects (mentioned along with the corresponding descriptions above) should also be provided, along with. Additionally, at least one of objects that define the VLANs to be blocked (crepifBlockedVlans1k, crepifBlockedVlans2k, crepifBlockedVlans3k, crepifBlockedVlans4k) should be provided with a non-empty value, when setting the value to anything other than 'none'. This value is only effective on the device acting as the REP primary edge." DEFVAL { none } ::= { crepInterfaceConfigEntry 13 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.601.1.2.1.1.1 | crepIfIndex | 0 | 0 | This object identifies the ifIndex-value assigned to the interface. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.2 | crepIfSegmentId | 0 | 0 | This object specifies the segment that the interface is part. This object can be modified when crepIfConfigRowStatus is 'active'… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.3 | crepIfOperStatus | 0 | 0 | This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in '… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.4 | crepIfPortRole | 0 | 0 | This object indicates the role or state of a REP port depending on its link status and whether it is forwarding or blocking traff… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.5 | crepIfPortID | 0 | 0 | This object indicates the REP port identifier automatically assigned by REP when enabled. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.6 | crepIfAdminEdgePortType | 0 | 0 | This object specifies the configured edge port type for the interface. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.7 | crepIfOperEdgePortType | 0 | 0 | This object indicates the actual edge port type for the interface. Value 'edge' indicates that the port is secondary edge port. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.8 | crepIfPreferredConfig | 0 | 0 | This object specifies if port should get preference to become the alternate port among other equal ports in the segment. Setting … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.9 | crepifBlockedVlans1k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 0 through 1023. … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.10 | crepifBlockedVlans2k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 1024 through 2047… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.11 | crepifBlockedVlans3k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 2048 through 3071… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.12 | crepifBlockedVlans4k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 3072 through 4095… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.14 | crepBlockPortNumInfo | 0 | 0 | This object specifies the offset of the port in the segment to be blocked for VLAN load balancing. Positive numbers indicate the… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.15 | crepBlockPortIdInfo | 0 | 0 | This object specifies the port identifier of the port in the segment to be blocked for VLAN load balancing. 'crepIfPortID' objec… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.16 | crepIfPreemptDelayTimer | 0 | 0 | This object specifies the interval of time that REP waits before triggering preemption after the segment is complete. The value -… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.17 | crepIfStcnPropagateToSTP | 0 | 0 | This object specifies if the REP edge propagates the segment topology change notifications to the spanning tree network. This valu… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.18 | crepIfStcnPropagateToOtherSegs | 0 | 0 | This object specifies the list of segments to which the REP edge propagates the segment topology change notifications. This value… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.19 | crepIfStcnPropagateToIf | 0 | 0 | This object specifies the interface to which the REP edge should propagate the segment topology change notifications. The interfa… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.20 | crepIfConfigRowStatus | 0 | 0 | This object is used to manage the creation, deletion, and modification of rows in this table. A row may be created using the 'Cre… |