Reference record for OID 1.3.6.1.4.1.9.9.601.1.2.1.1.14



parent
1.3.6.1.4.1.9.9.601.1.2.1.1 (crepInterfaceConfigEntry)
node code
14
node name
crepBlockPortNumInfo
dot oid
1.3.6.1.4.1.9.9.601.1.2.1.1.14
type
OBJECT-TYPE
asn1 oid
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) cisco(9) ciscoMgmt(9) ciscoResilientEthernetProtocolMIB(601) ciscoRepMIBObjects(1) crepInterfaceConfig(2) crepInterfaceConfigTable(1) crepInterfaceConfigEntry(1) crepBlockPortNumInfo(14)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) cisco(9) ciscoMgmt(9) ciscoResilientEthernetProtocolMIB(601) ciscoRepMIBObjects(1) crepInterfaceConfig(2) crepInterfaceConfigTable(1) crepInterfaceConfigEntry(1) crepBlockPortNumInfo(14)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprise(1) cisco(9) ciscoMgmt(9) ciscoResilientEthernetProtocolMIB(601) ciscoRepMIBObjects(1) crepInterfaceConfig(2) crepInterfaceConfigTable(1) crepInterfaceConfigEntry(1) crepBlockPortNumInfo(14)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) cisco(9) ciscoMgmt(9) ciscoResilientEthernetProtocolMIB(601) ciscoRepMIBObjects(1) crepInterfaceConfig(2) crepInterfaceConfigTable(1) crepInterfaceConfigEntry(1) crepBlockPortNumInfo(14)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) enterprise(1) cisco(9) ciscoMgmt(9) ciscoResilientEthernetProtocolMIB(601) ciscoRepMIBObjects(1) crepInterfaceConfig(2) crepInterfaceConfigTable(1) crepInterfaceConfigEntry(1) crepBlockPortNumInfo(14)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) enterprises(1) cisco(9) ciscoMgmt(9) ciscoResilientEthernetProtocolMIB(601) ciscoRepMIBObjects(1) crepInterfaceConfig(2) crepInterfaceConfigTable(1) crepInterfaceConfigEntry(1) crepBlockPortNumInfo(14)}
    • iri oid
  • /iso/identified-organization/dod/internet/private/enterprise/cisco/ciscoMgmt/ciscoResilientEthernetProtocolMIB/ciscoRepMIBObjects/crepInterfaceConfig/crepInterfaceConfigTable/crepInterfaceConfigEntry/crepBlockPortNumInfo
  • /iso/identified-organization/dod/internet/private/enterprises/cisco/ciscoMgmt/ciscoResilientEthernetProtocolMIB/ciscoRepMIBObjects/crepInterfaceConfig/crepInterfaceConfigTable/crepInterfaceConfigEntry/crepBlockPortNumInfo
  • /iso/org/dod/internet/private/enterprise/cisco/ciscoMgmt/ciscoResilientEthernetProtocolMIB/ciscoRepMIBObjects/crepInterfaceConfig/crepInterfaceConfigTable/crepInterfaceConfigEntry/crepBlockPortNumInfo
  • /iso/org/dod/internet/private/enterprises/cisco/ciscoMgmt/ciscoResilientEthernetProtocolMIB/ciscoRepMIBObjects/crepInterfaceConfig/crepInterfaceConfigTable/crepInterfaceConfigEntry/crepBlockPortNumInfo
  • /iso/iso-identified-organization/dod/internet/private/enterprise/cisco/ciscoMgmt/ciscoResilientEthernetProtocolMIB/ciscoRepMIBObjects/crepInterfaceConfig/crepInterfaceConfigTable/crepInterfaceConfigEntry/crepBlockPortNumInfo
  • /iso/iso-identified-organization/dod/internet/private/enterprises/cisco/ciscoMgmt/ciscoResilientEthernetProtocolMIB/ciscoRepMIBObjects/crepInterfaceConfig/crepInterfaceConfigTable/crepInterfaceConfigEntry/crepBlockPortNumInfo
    • iri by oid_info
    /ISO/Identified-Organization/6/1/4/1/9/9/601/1/2/1/1/14

    Description by circitor

    This object specifies the offset of the port in the segment
    to be blocked for VLAN load balancing. Positive numbers
    indicate the offset from the primary edge port and negative
    numbers indicates the downstream neighbor from the secondary
    edge port.

    [Sw E1]E1
    .
    .
    [Sw E2]E2

    Sw : Switch.
    E : Edge port.
    NE : Non-Edge port.
    E1/E2: Edge switches. E1 and E2 can either be same or
    different switches.

    In the segment depicted above, consider port E1 on 'Sw E1' is
    the primary edge and E2 on 'Sw E2' is the secondary edge.
    Value 1 for this object indicates primary edge port, 2 indicates
    NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on. Value -1
    indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3
    indicates NE1 on 'Sw N' and so on. Usage of value 0 is invalid.

    This value is only effective on the device acting as the REP
    primary edge and has relevance only if
    crepLoadBalanceBlockPortType = 'offset'.

    Parsed from file CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB.mib
    Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB

    Description by cisco_v1

    This object specifies the offset of the port in the segment
    to be blocked for VLAN load balancing. Positive numbers
    indicate the offset from the primary edge port and negative
    numbers indicates the downstream neighbor from the secondary
    edge port.

    [Sw E1]E1
    .
    .
    [Sw E2]E2

    Sw : Switch.
    E : Edge port.
    NE : Non-Edge port.
    E1/E2: Edge switches. E1 and E2 can either be same or
    different switches.

    In the segment depicted above, consider port E1 on 'Sw E1' is
    the primary edge and E2 on 'Sw E2' is the secondary edge.
    Value 1 for this object indicates primary edge port, 2 indicates
    NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on. Value -1
    indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3
    indicates NE1 on 'Sw N' and so on. Usage of value 0 is invalid.

    This value is only effective on the device acting as the REP
    primary edge and has relevance only if
    crepLoadBalanceBlockPortType = 'offset'.

    Description by mibdepot

    This object specifies the offset of the port in the segment
    to be blocked for VLAN load balancing. Positive numbers
    indicate the offset from the primary edge port and negative
    numbers indicates the downstream neighbor from the secondary
    edge port.

    [Sw E1]E1
    .
    .
    [Sw E2]E2

    Sw : Switch.
    E : Edge port.
    NE : Non-Edge port.
    E1/E2: Edge switches. E1 and E2 can either be same or
    different switches.

    In the segment depicted above, consider port E1 on 'Sw E1' is
    the primary edge and E2 on 'Sw E2' is the secondary edge.
    Value 1 for this object indicates primary edge port, 2 indicates
    NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on. Value -1
    indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3
    indicates NE1 on 'Sw N' and so on. Usage of value 0 is invalid.

    This value is only effective on the device acting as the REP
    primary edge and has relevance only if
    crepLoadBalanceBlockPortType = 'offset'.

    Parsed from file CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB.my.txt
    Company: None
    Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB

    Description by cisco

    This object specifies the offset of the port in the segment
    to be blocked for VLAN load balancing. Positive numbers
    indicate the offset from the primary edge port and negative
    numbers indicates the downstream neighbor from the secondary
    edge port.

    [Sw E1]E1
    .
    .
    [Sw E2]E2

    Sw : Switch.
    E : Edge port.
    NE : Non-Edge port.
    E1/E2: Edge switches. E1 and E2 can either be same or
    different switches.

    In the segment depicted above, consider port E1 on 'Sw E1' is
    the primary edge and E2 on 'Sw E2' is the secondary edge.
    Value 1 for this object indicates primary edge port, 2 indicates
    NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on. Value -1
    indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3
    indicates NE1 on 'Sw N' and so on. Usage of value 0 is invalid.

    This value is only effective on the device acting as the REP
    primary edge and has relevance only if
    crepLoadBalanceBlockPortType = 'offset'.

    Information by circitor

    crepBlockPortNumInfo OBJECT-TYPE
    SYNTAX          Integer32 (-256..256 )
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
        "This object specifies the offset of the port in the segment
        to be blocked for VLAN load balancing.  Positive numbers 
        indicate the offset from the primary edge port and negative
        numbers indicates the downstream neighbor from the secondary
        edge port.     

        [Sw E1]E1
                                                       .
                                                       .
        [Sw E2]E2

         Sw : Switch.
         E  : Edge port.
         NE : Non-Edge port.  
         E1/E2: Edge switches.  E1 and E2 can either be same or 
         different switches.

        In the segment depicted above, consider port E1 on 'Sw E1' is 
        the primary edge and E2 on 'Sw E2' is the secondary edge.  
        Value 1 for this object indicates primary edge port, 2 indicates
        NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on.  Value -1 
        indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3 
        indicates NE1 on 'Sw N' and so on.  Usage of value 0 is invalid.

        This value is only effective on the device acting as the REP
        primary edge and has relevance only if 
        crepLoadBalanceBlockPortType = 'offset'." 
    ::= { crepInterfaceConfigEntry 14 }

    Information by cisco_v1

    crepBlockPortNumInfo OBJECT-TYPE
    SYNTAX INTEGER(-256..256)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the offset of the port in the segment
        to be blocked for VLAN load balancing.  Positive numbers 
        indicate the offset from the primary edge port and negative
        numbers indicates the downstream neighbor from the secondary
        edge port.     
        
        [Sw E1]E1
                                                       .
                                                       .
        [Sw E2]E2
        
         Sw : Switch.
         E  : Edge port.
         NE : Non-Edge port.  
         E1/E2: Edge switches.  E1 and E2 can either be same or 
         different switches.
        
        In the segment depicted above, consider port E1 on 'Sw E1' is 
        the primary edge and E2 on 'Sw E2' is the secondary edge.  
        Value 1 for this object indicates primary edge port, 2 indicates
        NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on.  Value -1 
        indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3 
        indicates NE1 on 'Sw N' and so on.  Usage of value 0 is invalid.
        
        This value is only effective on the device acting as the REP
        primary edge and has relevance only if 
        crepLoadBalanceBlockPortType = 'offset'."
    ::= { crepInterfaceConfigEntry 14 }

    Information by oid_info

    Vendor: Cisco
    Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB

    [Automatically extracted from oidview.com]

    Information by mibdepot

    crepBlockPortNumInfo OBJECT-TYPE
    SYNTAX          Integer32 (-256..256 )
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
        "This object specifies the offset of the port in the segment
        to be blocked for VLAN load balancing.  Positive numbers 
        indicate the offset from the primary edge port and negative
        numbers indicates the downstream neighbor from the secondary
        edge port.     

        [Sw E1]E1
                                                       .
                                                       .
        [Sw E2]E2

         Sw : Switch.
         E  : Edge port.
         NE : Non-Edge port.  
         E1/E2: Edge switches.  E1 and E2 can either be same or 
         different switches.

        In the segment depicted above, consider port E1 on 'Sw E1' is 
        the primary edge and E2 on 'Sw E2' is the secondary edge.  
        Value 1 for this object indicates primary edge port, 2 indicates
        NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on.  Value -1 
        indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3 
        indicates NE1 on 'Sw N' and so on.  Usage of value 0 is invalid.

        This value is only effective on the device acting as the REP
        primary edge and has relevance only if 
        crepLoadBalanceBlockPortType = 'offset'." 
    ::= { crepInterfaceConfigEntry 14 }

    Information by cisco

    crepBlockPortNumInfo OBJECT-TYPE
    SYNTAX          Integer32 (-256..256)
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
        "This object specifies the offset of the port in the segment
        to be blocked for VLAN load balancing.  Positive numbers 
        indicate the offset from the primary edge port and negative
        numbers indicates the downstream neighbor from the secondary
        edge port.     

        [Sw E1]E1
                                                       .
                                                       .
        [Sw E2]E2

         Sw : Switch.
         E  : Edge port.
         NE : Non-Edge port.  
         E1/E2: Edge switches.  E1 and E2 can either be same or 
         different switches.

        In the segment depicted above, consider port E1 on 'Sw E1' is 
        the primary edge and E2 on 'Sw E2' is the secondary edge.  
        Value 1 for this object indicates primary edge port, 2 indicates
        NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on.  Value -1 
        indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3 
        indicates NE1 on 'Sw N' and so on.  Usage of value 0 is invalid.

        This value is only effective on the device acting as the REP
        primary edge and has relevance only if 
        crepLoadBalanceBlockPortType = 'offset'." 
    ::= { crepInterfaceConfigEntry 14 }

    First Registration Authority (recovered by parent 1.3.6.1.4.1.9)

    Greg Satz

    Current Registration Authority (recovered by parent 1.3.6.1.4.1.9)

    Cisco Systems, Inc.

    Brothers (19)

    OIDNameSub childrenSub Nodes TotalDescription
    1.3.6.1.4.1.9.9.601.1.2.1.1.1 crepIfIndex 0 0 This object identifies the ifIndex-value assigned to the
    interface.
    1.3.6.1.4.1.9.9.601.1.2.1.1.2 crepIfSegmentId 0 0 This object specifies the segment that the interface is part.
    This object can be modified when crepIfConfigRowStatus is 'active'…
    1.3.6.1.4.1.9.9.601.1.2.1.1.3 crepIfOperStatus 0 0 This object indicates the current operational link state
    of the REP port. If a REP configured interface is down,
    it will be in '…
    1.3.6.1.4.1.9.9.601.1.2.1.1.4 crepIfPortRole 0 0 This object indicates the role or state of a REP port depending
    on its link status and whether it is forwarding or blocking
    traff…
    1.3.6.1.4.1.9.9.601.1.2.1.1.5 crepIfPortID 0 0 This object indicates the REP port identifier automatically
    assigned by REP when enabled.
    1.3.6.1.4.1.9.9.601.1.2.1.1.6 crepIfAdminEdgePortType 0 0 This object specifies the configured edge port type for the
    interface.
    1.3.6.1.4.1.9.9.601.1.2.1.1.7 crepIfOperEdgePortType 0 0 This object indicates the actual edge port type for the
    interface. Value 'edge' indicates that the port is secondary
    edge port.
    1.3.6.1.4.1.9.9.601.1.2.1.1.8 crepIfPreferredConfig 0 0 This object specifies if port should get preference to become
    the alternate port among other equal ports in the segment.

    Setting …
    1.3.6.1.4.1.9.9.601.1.2.1.1.9 crepifBlockedVlans1k 0 0 This object specifies the list of VLANs configured to be
    blocked at the alternate port for VLANs with values of 0 through
    1023. …
    1.3.6.1.4.1.9.9.601.1.2.1.1.10 crepifBlockedVlans2k 0 0 This object specifies the list of VLANs configured to be
    blocked at the alternate port for VLANs with values of 1024
    through 2047…
    1.3.6.1.4.1.9.9.601.1.2.1.1.11 crepifBlockedVlans3k 0 0 This object specifies the list of VLANs configured to be
    blocked at the alternate port for VLANs with values of 2048
    through 3071…
    1.3.6.1.4.1.9.9.601.1.2.1.1.12 crepifBlockedVlans4k 0 0 This object specifies the list of VLANs configured to be
    blocked at the alternate port for VLANs with values of 3072
    through 4095…
    1.3.6.1.4.1.9.9.601.1.2.1.1.13 crepLoadBalanceBlockPortType 0 0 This object specifies the method defined to identify the
    alternate port in the segment that takes part in VLAN load
    balancing by …
    1.3.6.1.4.1.9.9.601.1.2.1.1.15 crepBlockPortIdInfo 0 0 This object specifies the port identifier of the port in the
    segment to be blocked for VLAN load balancing. 'crepIfPortID'
    objec…
    1.3.6.1.4.1.9.9.601.1.2.1.1.16 crepIfPreemptDelayTimer 0 0 This object specifies the interval of time that REP waits
    before triggering preemption after the segment is complete.

    The value -…
    1.3.6.1.4.1.9.9.601.1.2.1.1.17 crepIfStcnPropagateToSTP 0 0 This object specifies if the REP edge propagates the
    segment topology change notifications to the spanning
    tree network.

    This valu…
    1.3.6.1.4.1.9.9.601.1.2.1.1.18 crepIfStcnPropagateToOtherSegs 0 0 This object specifies the list of segments to which the
    REP edge propagates the segment topology change notifications.

    This value…
    1.3.6.1.4.1.9.9.601.1.2.1.1.19 crepIfStcnPropagateToIf 0 0 This object specifies the interface to which the REP edge
    should propagate the segment topology change notifications.
    The interfa…
    1.3.6.1.4.1.9.9.601.1.2.1.1.20 crepIfConfigRowStatus 0 0 This object is used to manage the creation, deletion, and
    modification of rows in this table.

    A row may be created using the 'Cre…