This object indicates the current operational link state
of the REP port. If a REP configured interface is down,
it will be in 'initDown' state.
'none' - REP is not operational on the interface. This
value is used when sending the crepLinkStatus
notification when REP configuration is removed
from the interface.
'initDown' - initial REP link state.
'noNeighbor' - state in which REP is yet to discover its
neighbor.
'oneWay' - the state in which messages have been received
from the neighbor but the link has not been
declared to be twoWay yet.
'twoWay' - the fully operational state for REP.
'flapping' - the state in which there is a mismatch in the
received port information (either local or
remote) for the neighbor.
'wait' - the forced transient state before REP starts
discovering its neighbor.
'unknown' - the link state cannot be determined.
Parsed from file CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB.mib
Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
This object indicates the current operational link state
of the REP port. If a REP configured interface is down,
it will be in 'initDown' state.
'none' - REP is not operational on the interface. This
value is used when sending the crepLinkStatus
notification when REP configuration is removed
from the interface.
'initDown' - initial REP link state.
'noNeighbor' - state in which REP is yet to discover its
neighbor.
'oneWay' - the state in which messages have been received
from the neighbor but the link has not been
declared to be twoWay yet.
'twoWay' - the fully operational state for REP.
'flapping' - the state in which there is a mismatch in the
received port information (either local or
remote) for the neighbor.
'wait' - the forced transient state before REP starts
discovering its neighbor.
'unknown' - the link state cannot be determined.
This object indicates the current operational link state
of the REP port. If a REP configured interface is down,
it will be in 'initDown' state.
'none' - REP is not operational on the interface. This
value is used when sending the crepLinkStatus
notification when REP configuration is removed
from the interface.
'initDown' - initial REP link state.
'noNeighbor' - state in which REP is yet to discover its
neighbor.
'oneWay' - the state in which messages have been received
from the neighbor but the link has not been
declared to be twoWay yet.
'twoWay' - the fully operational state for REP.
'flapping' - the state in which there is a mismatch in the
received port information (either local or
remote) for the neighbor.
'wait' - the forced transient state before REP starts
discovering its neighbor.
'unknown' - the link state cannot be determined.
Parsed from file CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB.my.txt
Company: None
Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
This object indicates the current operational link state
of the REP port. If a REP configured interface is down,
it will be in 'initDown' state.
'none' - REP is not operational on the interface. This
value is used when sending the crepLinkStatus
notification when REP configuration is removed
from the interface.
'initDown' - initial REP link state.
'noNeighbor' - state in which REP is yet to discover its
neighbor.
'oneWay' - the state in which messages have been received
from the neighbor but the link has not been
declared to be twoWay yet.
'twoWay' - the fully operational state for REP.
'flapping' - the state in which there is a mismatch in the
received port information (either local or
remote) for the neighbor.
'wait' - the forced transient state before REP starts
discovering its neighbor.
'unknown' - the link state cannot be determined.
crepIfOperStatus OBJECT-TYPE SYNTAX INTEGER { none(1), initDown(2), noNeighbour(3), oneWay(4), twoWay(5), flapping(6), wait(7), unknown(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - REP is not operational on the interface. This value is used when sending the crepLinkStatus notification when REP configuration is removed from the interface. 'initDown' - initial REP link state. 'noNeighbor' - state in which REP is yet to discover its neighbor. 'oneWay' - the state in which messages have been received from the neighbor but the link has not been declared to be twoWay yet. 'twoWay' - the fully operational state for REP. 'flapping' - the state in which there is a mismatch in the received port information (either local or remote) for the neighbor. 'wait' - the forced transient state before REP starts discovering its neighbor. 'unknown' - the link state cannot be determined." ::= { crepInterfaceConfigEntry 3 }
crepIfOperStatus OBJECT-TYPE SYNTAX INTEGER { none(1), initDown(2), noNeighbour(3), oneWay(4), twoWay(5), flapping(6), wait(7), unknown(8) } ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - REP is not operational on the interface. This value is used when sending the crepLinkStatus notification when REP configuration is removed from the interface. 'initDown' - initial REP link state. 'noNeighbor' - state in which REP is yet to discover its neighbor. 'oneWay' - the state in which messages have been received from the neighbor but the link has not been declared to be twoWay yet. 'twoWay' - the fully operational state for REP. 'flapping' - the state in which there is a mismatch in the received port information (either local or remote) for the neighbor. 'wait' - the forced transient state before REP starts discovering its neighbor. 'unknown' - the link state cannot be determined." ::= { crepInterfaceConfigEntry 3 }
Vendor: Cisco
Module: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
[Automatically extracted from oidview.com]
crepIfOperStatus OBJECT-TYPE SYNTAX INTEGER { none(1), initDown(2), noNeighbour(3), oneWay(4), twoWay(5), flapping(6), wait(7), unknown(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - REP is not operational on the interface. This value is used when sending the crepLinkStatus notification when REP configuration is removed from the interface. 'initDown' - initial REP link state. 'noNeighbor' - state in which REP is yet to discover its neighbor. 'oneWay' - the state in which messages have been received from the neighbor but the link has not been declared to be twoWay yet. 'twoWay' - the fully operational state for REP. 'flapping' - the state in which there is a mismatch in the received port information (either local or remote) for the neighbor. 'wait' - the forced transient state before REP starts discovering its neighbor. 'unknown' - the link state cannot be determined." ::= { crepInterfaceConfigEntry 3 }
crepIfOperStatus OBJECT-TYPE SYNTAX INTEGER { none(1), initDown(2), noNeighbour(3), oneWay(4), twoWay(5), flapping(6), wait(7), unknown(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - REP is not operational on the interface. This value is used when sending the crepLinkStatus notification when REP configuration is removed from the interface. 'initDown' - initial REP link state. 'noNeighbor' - state in which REP is yet to discover its neighbor. 'oneWay' - the state in which messages have been received from the neighbor but the link has not been declared to be twoWay yet. 'twoWay' - the fully operational state for REP. 'flapping' - the state in which there is a mismatch in the received port information (either local or remote) for the neighbor. 'wait' - the forced transient state before REP starts discovering its neighbor. 'unknown' - the link state cannot be determined." ::= { crepInterfaceConfigEntry 3 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.601.1.2.1.1.1 | crepIfIndex | 0 | 0 | This object identifies the ifIndex-value assigned to the interface. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.2 | crepIfSegmentId | 0 | 0 | This object specifies the segment that the interface is part. This object can be modified when crepIfConfigRowStatus is 'active'… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.4 | crepIfPortRole | 0 | 0 | This object indicates the role or state of a REP port depending on its link status and whether it is forwarding or blocking traff… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.5 | crepIfPortID | 0 | 0 | This object indicates the REP port identifier automatically assigned by REP when enabled. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.6 | crepIfAdminEdgePortType | 0 | 0 | This object specifies the configured edge port type for the interface. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.7 | crepIfOperEdgePortType | 0 | 0 | This object indicates the actual edge port type for the interface. Value 'edge' indicates that the port is secondary edge port. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.8 | crepIfPreferredConfig | 0 | 0 | This object specifies if port should get preference to become the alternate port among other equal ports in the segment. Setting … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.9 | crepifBlockedVlans1k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 0 through 1023. … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.10 | crepifBlockedVlans2k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 1024 through 2047… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.11 | crepifBlockedVlans3k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 2048 through 3071… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.12 | crepifBlockedVlans4k | 0 | 0 | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 3072 through 4095… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.13 | crepLoadBalanceBlockPortType | 0 | 0 | This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.14 | crepBlockPortNumInfo | 0 | 0 | This object specifies the offset of the port in the segment to be blocked for VLAN load balancing. Positive numbers indicate the… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.15 | crepBlockPortIdInfo | 0 | 0 | This object specifies the port identifier of the port in the segment to be blocked for VLAN load balancing. 'crepIfPortID' objec… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.16 | crepIfPreemptDelayTimer | 0 | 0 | This object specifies the interval of time that REP waits before triggering preemption after the segment is complete. The value -… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.17 | crepIfStcnPropagateToSTP | 0 | 0 | This object specifies if the REP edge propagates the segment topology change notifications to the spanning tree network. This valu… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.18 | crepIfStcnPropagateToOtherSegs | 0 | 0 | This object specifies the list of segments to which the REP edge propagates the segment topology change notifications. This value… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.19 | crepIfStcnPropagateToIf | 0 | 0 | This object specifies the interface to which the REP edge should propagate the segment topology change notifications. The interfa… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.20 | crepIfConfigRowStatus | 0 | 0 | This object is used to manage the creation, deletion, and modification of rows in this table. A row may be created using the 'Cre… |