This MIB module defines textual conventions used by the MIB
modules defining objects describing flow monitoring.
GLOSSARY
============
Alarm Action - a method used by the device to signal changes in
an alarm condition.
Alarm Aggregation - a technique used to efficiently monitor the
same standing condition for a flow set.
Alarm Condition - a standing condition for which the device
signals changes in state.
Alarm Group - a flow set for which the device monitors a
configured standing condition, raising an alarm when a
configured number of flows in the flow set assert the
standing standing.
Alarm Severity - the relative disposition of an alarm condition
when raised by the device. For example, a provider may
regard a flow stop alarm as having a higher severity than a
flow's loss fraction exceeding a configured threshold.
Flow Monitor - a hardware or software entity that classifies
traffic flows, collects flow data, and periodically
computes flow metrics.
Flow Metric - a measurement that reflects the quality of a
traffic flow.
Flow Point - represents the ingress or egress of a traffic flow.
Flow Set - a group of traffic flows.
Measurement Interval - the length of time over which a flow
monitor collects data related to a traffic flow, after which
the flow monitor computes flow metrics using the collected
data.
Standing Condition - represents a lasting error, fault, or
warning resulting from the application of a set of criteria
to the state of an entity, such as a flow monitor or traffic
flow. For example, a flow monitor may assert a standing
condition if the number of traffic flows that expire in a
meansurement interval exceeds a configured threshold.
Traffic Flow - a unidirectional stream of packets conforming to
a classifier. For example, packets having a particular
source IP address, destination IP address, protocol type,
source port number, and destination port number.
Parsed from file CISCO-FLOW-MONITOR-TC-MIB.mib
Module: CISCO-FLOW-MONITOR-TC-MIB
This MIB module defines textual conventions used by the MIB
modules defining objects describing flow monitoring.
GLOSSARY
============
Alarm Action - a method used by the device to signal changes in
an alarm condition.
Alarm Aggregation - a technique used to efficiently monitor the
same standing condition for a flow set.
Alarm Condition - a standing condition for which the device
signals changes in state.
Alarm Group - a flow set for which the device monitors a
configured standing condition, raising an alarm when a
configured number of flows in the flow set assert the
standing standing.
Alarm Severity - the relative disposition of an alarm condition
when raised by the device. For example, a provider may
regard a flow stop alarm as having a higher severity than a
flow's loss fraction exceeding a configured threshold.
Flow Monitor - a hardware or software entity that classifies
traffic flows, collects flow data, and periodically
computes flow metrics.
Flow Metric - a measurement that reflects the quality of a
traffic flow.
Flow Point - represents the ingress or egress of a traffic flow.
Flow Set - a group of traffic flows.
Measurement Interval - the length of time over which a flow
monitor collects data related to a traffic flow, after which
the flow monitor computes flow metrics using the collected
data.
Standing Condition - represents a lasting error, fault, or
warning resulting from the application of a set of criteria
to the state of an entity, such as a flow monitor or traffic
flow. For example, a flow monitor may assert a standing
condition if the number of traffic flows that expire in a
meansurement interval exceeds a configured threshold.
Traffic Flow - a unidirectional stream of packets conforming to
a classifier. For example, packets having a particular
source IP address, destination IP address, protocol type,
source port number, and destination port number.
Parsed from file CISCO-FLOW-MONITOR-TC-MIB.my.txt
Company: None
Module: CISCO-FLOW-MONITOR-TC-MIB
This MIB module defines textual conventions used by the MIB
modules defining objects describing flow monitoring.
GLOSSARY
============
Alarm Action - a method used by the device to signal changes in
an alarm condition.
Alarm Aggregation - a technique used to efficiently monitor the
same standing condition for a flow set.
Alarm Condition - a standing condition for which the device
signals changes in state.
Alarm Group - a flow set for which the device monitors a
configured standing condition, raising an alarm when a
configured number of flows in the flow set assert the
standing standing.
Alarm Severity - the relative disposition of an alarm condition
when raised by the device. For example, a provider may
regard a flow stop alarm as having a higher severity than a
flow's loss fraction exceeding a configured threshold.
Flow Monitor - a hardware or software entity that classifies
traffic flows, collects flow data, and periodically
computes flow metrics.
Flow Metric - a measurement that reflects the quality of a
traffic flow.
Flow Point - represents the ingress or egress of a traffic flow.
Flow Set - a group of traffic flows.
Measurement Interval - the length of time over which a flow
monitor collects data related to a traffic flow, after which
the flow monitor computes flow metrics using the collected
data.
Standing Condition - represents a lasting error, fault, or
warning resulting from the application of a set of criteria
to the state of an entity, such as a flow monitor or traffic
flow. For example, a flow monitor may assert a standing
condition if the number of traffic flows that expire in a
meansurement interval exceeds a configured threshold.
Traffic Flow - a unidirectional stream of packets conforming to
a classifier. For example, packets having a particular
source IP address, destination IP address, protocol type,
source port number, and destination port number.
ciscoFlowMonitorTcMIB MODULE-IDENTITY LAST-UPDATED "200812090000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "This MIB module defines textual conventions used by the MIB modules defining objects describing flow monitoring. GLOSSARY ============ Alarm Action - a method used by the device to signal changes in an alarm condition. Alarm Aggregation - a technique used to efficiently monitor the same standing condition for a flow set. Alarm Condition - a standing condition for which the device signals changes in state. Alarm Group - a flow set for which the device monitors a configured standing condition, raising an alarm when a configured number of flows in the flow set assert the standing standing. Alarm Severity - the relative disposition of an alarm condition when raised by the device. For example, a provider may regard a flow stop alarm as having a higher severity than a flow's loss fraction exceeding a configured threshold. Flow Monitor - a hardware or software entity that classifies traffic flows, collects flow data, and periodically computes flow metrics. Flow Metric - a measurement that reflects the quality of a traffic flow. Flow Point - represents the ingress or egress of a traffic flow. Flow Set - a group of traffic flows. Measurement Interval - the length of time over which a flow monitor collects data related to a traffic flow, after which the flow monitor computes flow metrics using the collected data. Standing Condition - represents a lasting error, fault, or warning resulting from the application of a set of criteria to the state of an entity, such as a flow monitor or traffic flow. For example, a flow monitor may assert a standing condition if the number of traffic flows that expire in a meansurement interval exceeds a configured threshold. Traffic Flow - a unidirectional stream of packets conforming to a classifier. For example, packets having a particular source IP address, destination IP address, protocol type, source port number, and destination port number. " REVISION "200812090000Z" DESCRIPTION "The initial version of the MIB module." ::= { ciscoMgmt 688 }
ciscoFlowMonitorTcMIB OBJECT IDENTIFIER ::= { ciscoMgmt 688 }
Vendor: Cisco
Module: CISCO-FLOW-MONITOR-TC-MIB
[Automatically extracted from oidview.com]
ciscoFlowMonitorTcMIB MODULE-IDENTITY LAST-UPDATED "200812090000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "This MIB module defines textual conventions used by the MIB modules defining objects describing flow monitoring. GLOSSARY ============ Alarm Action - a method used by the device to signal changes in an alarm condition. Alarm Aggregation - a technique used to efficiently monitor the same standing condition for a flow set. Alarm Condition - a standing condition for which the device signals changes in state. Alarm Group - a flow set for which the device monitors a configured standing condition, raising an alarm when a configured number of flows in the flow set assert the standing standing. Alarm Severity - the relative disposition of an alarm condition when raised by the device. For example, a provider may regard a flow stop alarm as having a higher severity than a flow's loss fraction exceeding a configured threshold. Flow Monitor - a hardware or software entity that classifies traffic flows, collects flow data, and periodically computes flow metrics. Flow Metric - a measurement that reflects the quality of a traffic flow. Flow Point - represents the ingress or egress of a traffic flow. Flow Set - a group of traffic flows. Measurement Interval - the length of time over which a flow monitor collects data related to a traffic flow, after which the flow monitor computes flow metrics using the collected data. Standing Condition - represents a lasting error, fault, or warning resulting from the application of a set of criteria to the state of an entity, such as a flow monitor or traffic flow. For example, a flow monitor may assert a standing condition if the number of traffic flows that expire in a meansurement interval exceeds a configured threshold. Traffic Flow - a unidirectional stream of packets conforming to a classifier. For example, packets having a particular source IP address, destination IP address, protocol type, source port number, and destination port number. " REVISION "200812090000Z" DESCRIPTION "The initial version of the MIB module." ::= { ciscoMgmt 688 }
ciscoFlowMonitorTcMIB MODULE-IDENTITY LAST-UPDATED "200812090000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "This MIB module defines textual conventions used by the MIB modules defining objects describing flow monitoring. GLOSSARY ============ Alarm Action - a method used by the device to signal changes in an alarm condition. Alarm Aggregation - a technique used to efficiently monitor the same standing condition for a flow set. Alarm Condition - a standing condition for which the device signals changes in state. Alarm Group - a flow set for which the device monitors a configured standing condition, raising an alarm when a configured number of flows in the flow set assert the standing standing. Alarm Severity - the relative disposition of an alarm condition when raised by the device. For example, a provider may regard a flow stop alarm as having a higher severity than a flow's loss fraction exceeding a configured threshold. Flow Monitor - a hardware or software entity that classifies traffic flows, collects flow data, and periodically computes flow metrics. Flow Metric - a measurement that reflects the quality of a traffic flow. Flow Point - represents the ingress or egress of a traffic flow. Flow Set - a group of traffic flows. Measurement Interval - the length of time over which a flow monitor collects data related to a traffic flow, after which the flow monitor computes flow metrics using the collected data. Standing Condition - represents a lasting error, fault, or warning resulting from the application of a set of criteria to the state of an entity, such as a flow monitor or traffic flow. For example, a flow monitor may assert a standing condition if the number of traffic flows that expire in a meansurement interval exceeds a configured threshold. Traffic Flow - a unidirectional stream of packets conforming to a classifier. For example, packets having a particular source IP address, destination IP address, protocol type, source port number, and destination port number. " REVISION "200812090000Z" DESCRIPTION "The initial version of the MIB module." ::= { ciscoMgmt 688 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.9.9.638 | ciscoAgwMIB | 3 | 324 | This module manages Cisco's WiMAX ASN Gateway (ASN-GW). A WiMAX network supports wireless data communication through WiMAX radio … |
| 1.3.6.1.4.1.9.9.639 | ciscoOtnIfMIB | 3 | 137 | This MIB module defines the managed objects for physical layer characteristics of DWDM optical channel interfaces and performanc… |
| 1.3.6.1.4.1.9.9.640 | ciscoImageLicenseMgmtMIB | 3 | 31 | The MIB module for managing the running image level of a Cisco device. Cisco's licensing mechanism provides flexibility to run a … |
| 1.3.6.1.4.1.9.9.642 | ciscoBridgeDomainMIB | 3 | 24 | A bridge domain is one of the means by which it is possible to define a broadcast domain on a bridging device. It is an alternati… |
| 1.3.6.1.4.1.9.9.643 | ciscoTelepresenceMIB | 3 | 119 | The MIB module defines the managed objects for a Telepresence system. Telepresence refers to a set of technologies which allow a p… |
| 1.3.6.1.4.1.9.9.644 | ciscoTelepresenceCallMIB | 3 | 178 | The MIB module defines the managed objects for Telepresence calls. Telepresence refers to a set of technologies which allow a pers… |
| 1.3.6.1.4.1.9.9.645 | ciscoEtherExtMIB | 3 | 18 | The MIB module to describe generic objects for ethernet-like network interfaces. This MIB provides ethernet-like network interfac… |
| 1.3.6.1.4.1.9.9.646 | ciscoAonStatusMIB | 3 | 80 | This MIB module defines managed objects that facilitate the management of AON node. The information available through this MIB in… |
| 1.3.6.1.4.1.9.9.647 | ciscoGgsnExtMIB | 3 | 212 | This MIB module extends the CISCO-GGSN-MIB. This MIB module manages the Gateway GPRS Support Node (GGSN) devices. A GGSN device pr… |
| 1.3.6.1.4.1.9.9.648 | ciscoVirtualInterfaceMIB | 2 | 32 | The MIB module for creation and deletion of Virtual Interfaces and Virtual Interface Groups. In addition to this MIB, interface … |
| 1.3.6.1.4.1.9.9.650 | ciscoL4L7moduleRedundancyMIB | 3 | 71 | The L4-7 SLB devices are used for scaling websites, building web enabled applications, and migrating to web services. The followin… |
| 1.3.6.1.4.1.9.9.651 | ciscoCommonRolesExtMIB | 3 | 37 | A MIB Module for managing the roles that are common between access methods like Command Line Interface (CLI), SNMP and XML interf… |
| 1.3.6.1.4.1.9.9.652 | ciscoSwitchStatsMIB | 3 | 106 | The MIB module provides management information for configuration and monitoring of traffic statistics on Cisco's switching device… |
| 1.3.6.1.4.1.9.9.653 | ciscoAdmissionPolicyMIB | 3 | 36 | This MIB module defines managed objects that facilitate the management of policies upon host(s) admission to a network. The inform… |
| 1.3.6.1.4.1.9.9.654 | ciscoMabMIB | 3 | 20 | MIB module for monitoring and configuring MAC Authentication Bypass (MAB) feature in the system. MAC Auth Bypass feature provides… |
| 1.3.6.1.4.1.9.9.655 | ciscoDigitalMediaSystemsMIB | 3 | 195 | Acronyms and Definitions The following acronyms and terms are used in this document: DMS: Digital Media Systems DAM: Digital As… |
| 1.3.6.1.4.1.9.9.656 | ciscoAuthFrameworkMIB | 3 | 117 | MIB module for Authentication Framework in the system. Authentication Framework provides generic configurations for authenticatio… |
| 1.3.6.1.4.1.9.9.657 | ciscoSbcCallStatsMIB | 3 | 201 | The main purpose of this MIB is to define the statistics information for Session Border Controller application. The statistics ar… |
| 1.3.6.1.4.1.9.9.658 | ciscoSessBorderCtrlrEventMIB | 3 | 208 | The main purpose of this MIB is to define the SNMP notifications and alarms generated by Session Border Controller application an… |
| 1.3.6.1.4.1.9.9.660 | ciscoNportVirtualizationMIB | 3 | 19 | The MIB module for the management of N_port Virtualization or NPV within the framework of Cisco's N_port virtualization (NPV) Arc… |
| 1.3.6.1.4.1.9.9.661 | ciscoWan3gMIB | 3 | 378 | This MIB module provides network management support for Cisco cellular 3G WAN products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS … |
| 1.3.6.1.4.1.9.9.662 | ciscoCbpTcMIB | 0 | 0 | This MIB module defines textual conventions used by the CISCO-CBP-BASE-CFG-MIB, CISCO-CBP-BASE-MON-MIB, and any MIB modules exten… |
| 1.3.6.1.4.1.9.9.663 | ciscoSwitchHardwareCapacityMIB | 3 | 141 | This MIB module defines the managed objects for hardware capacity of Cisco switching devices. The hardware capacity information c… |
| 1.3.6.1.4.1.9.9.664 | ciscoMmodalContactAppsMIB | 3 | 359 | The Cisco Unified Multi-Modal Contact Applications (MMCA) platform is a highly scalable, modular, extensible, open and secure pl… |
| 1.3.6.1.4.1.9.9.667 | ciscoServiceControllerMIB | 2 | 31 | This MIB module defines objects describing traffic controllers used by a service control entity. A service control entity is a ne… |
| 1.3.6.1.4.1.9.9.668 | ciscoP2PIfMIB | 3 | 16 | The Point to Point Interface MIB module. This MIB manages the generic objects for Serial link or SONET/SDH like point to point ne… |
| 1.3.6.1.4.1.9.9.669 | ciscoCdmaPdsnExtMIB | 3 | 178 | This MIB is an extension to the CISCO-CDMA-PDSN-MIB. A CDMA network supports wireless data communication through 3G CDMA radio acc… |
| 1.3.6.1.4.1.9.9.670 | ciscoReportIntervalTcMIB | 0 | 0 | CISCO-REPORT-INTERVAL-TC-MIB |
| 1.3.6.1.4.1.9.9.672 | ciscoMobilityTapMIB | 3 | 24 | This module manages Cisco's intercept feature for Mobility Gateway Products. This MIB is used along with CISCO-TAP2-MIB MIB to int… |
| 1.3.6.1.4.1.9.9.673 | ciscoFCoEMIB | 2 | 45 | This MIB module is for configuring and monitoring Fibre Channel over Ethernet (FCoE) related entities. This MIB defines the Virtu… |
| 1.3.6.1.4.1.9.9.679 | ciscoIeee8021CfmExtMIB | 3 | 55 | A MIB module for extending the IEEE8021-CFM-MIB and IEEE8021-CFM-V2-MIB to add objects which provide additional information about… |
| 1.3.6.1.4.1.9.9.680 | ciscoNhrpExtMIB | 3 | 36 | This MIB module is an extension of the NHRP MIB module as defined in RFC 2677. It defines notifications associated with critical … |
| 1.3.6.1.4.1.9.9.683 | ciscoEnergywiseMIB | 3 | 162 | The MIB is used to manage and optimize power usage in networks. Cisco EnergyWise is a specification of data, discovery and protoco… |
| 1.3.6.1.4.1.9.9.686 | ciscoLwappInterfaceMIB | 3 | 27 | ciscoLwappInterfaceMIB MODULE-IDENTITY LAST-UPDATED "200901090000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Syste… |
| 1.3.6.1.4.1.9.9.689 | ciscoSlbDfpMIB | 3 | 22 | This MIB reports the congestion status of the real server. A server can be in congested state due to high memory consumption, hig… |
| 1.3.6.1.4.1.9.9.690 | ciscoMobilePolicyChargingControlMIB | 3 | 143 | Mobile PCC Infrastructure built on top of Policy Shim Layer, is a common interface to send and receive PCC related messages for a… |
| 1.3.6.1.4.1.9.9.691 | ciscoEthernetFabricExtenderMIB | 3 | 23 | The MIB module for configuring one or more fabric extenders to connect into a core switch. Since fabric extenders might not be m… |
| 1.3.6.1.4.1.9.9.692 | ciscoFlowMonitorMIB | 4 | 195 | This MIB module defines objects that describe flow monitoring. A typical application of this MIB module will facilitate monitorin… |
| 1.3.6.1.4.1.9.9.693 | ciscoServiceControlAttackMIB | 3 | 55 | This MIB provides data related to different types of attacks detected by a service control entity. A service control entity is a … |
| 1.3.6.1.4.1.9.9.694 | ciscoCtsTcMIB | 0 | 0 | This module defines the textual conventions used within Cisco Trusted Security framework. |
| 1.3.6.1.4.1.9.9.695 | ciscoGtcapMIB | 3 | 194 | The MIB for Transaction Capabilities(TCAP) messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer P… |
| 1.3.6.1.4.1.9.9.696 | ciscoBootHwDiagsMIB | 3 | 22 | This MIB is used to configure those devices that support boot-time hardware diagnostics. It provides the reports about the respe… |
| 1.3.6.1.4.1.9.9.697 | ciscoIpCbrMetricsMIB | 4 | 42 | This MIB module defines objects that describe the a set of metrics used to measure the quality of a IP CBR traffic flow. An IP CB… |
| 1.3.6.1.4.1.9.9.698 | ciscoObmiMIB | 3 | 60 | The On-Board Management Interface (OBMI) provides an out-of-band communications channel (in Cisco terms: a console port), that is… |
| 1.3.6.1.4.1.9.9.699 | ciscoMdiMetricsMIB | 4 | 46 | This MIB module defines objects that describe the Media Delivery Index (MDI). The MDI [RFC4445] measurement describes the qualit… |
| 1.3.6.1.4.1.9.9.700 | ciscoCableL2vpnMIB | 3 | 28 | This MIB module defines managed objects that facilitate the management of Cisco devices complying to the DOCSIS L2VPN Feature for… |
| 1.3.6.1.4.1.9.9.701 | ciscoSeuMitigationMIB | 3 | 51 | This MIB reports the status of non-automatic and automatic, rate-adaptive Single Event Upset (SEU) mitigation algorithms and adju… |
| 1.3.6.1.4.1.9.9.702 | ciscoSanBaseSvcMIB | 3 | 57 | Common MIB module to manage services in Storage Area Network (SAN). Service is deployed on service nodes on multiple switches fo… |
| 1.3.6.1.4.1.9.9.703 | ciscoRtpMetricsMIB | 4 | 61 | This MIB module defines objects that describe the quality metrics of RTP streams, similar to those described by an RTCP Receiver … |
| 1.3.6.1.4.1.9.9.706 | ciscoInterfaceXcvrMonitorMIB | 3 | 33 | A MIB module that provides monitoring information about the transceivers plugged into interface on a system. |
| 1.3.6.1.4.1.9.9.708 | ciscoContentDeliveryStreamingMIB | 2 | 30 | This MIB instrumentation is for managing the Content Delivery and Streaming functionality on Cisco devices. Contents are ingested… |
| 1.3.6.1.4.1.9.9.709 | ciscoVlanGroupMIB | 3 | 18 | MIB module for monitoring and configuring VLAN Group Mapping information. |
| 1.3.6.1.4.1.9.9.710 | ciscoVirtualNicMIB | 3 | 36 | This MIB module defines MIB objects which provide mechanisms to manage the parameters used by or related to Virtual NIC. Virtual s… |
| 1.3.6.1.4.1.9.9.711 | ciscoVrfMIB | 3 | 48 | The MIB module for provisioning and managing network virtualization features. This module provides manageability for VRF, VRF-Lit… |
| 1.3.6.1.4.1.9.9.712 | ciscoWirelessNotificationMIB | 3 | 30 | This MIB is intended to be implemented on those Network Management applications that manage a network of wireless devices through… |
| 1.3.6.1.4.1.9.9.713 | ciscoTrustSecPolicyMIB | 3 | 204 | This MIB module defines managed objects that facilitate the management of various policies within the Cisco Trusted Security (Tru… |
| 1.3.6.1.4.1.9.9.714 | ciscoHwModuleControlMIB | 3 | 27 | The MIB module providing configuration and control information for management of hardware modules and components on Cisco devices… |
| 1.3.6.1.4.1.9.9.715 | ciscoEntityQfpMIB | 3 | 82 | This MIB module defines managed objects that facilitate the management of Quantum Flow Processors (QFP), which are listed in the … |
| 1.3.6.1.4.1.9.9.716 | ciscoVoIpTapMIB | 3 | 18 | This module manages Cisco's intercept feature for Voice over IP (VoIP). This MIB is used along with CISCO-TAP2-MIB to intercept V… |
| 1.3.6.1.4.1.9.9.718 | ciscoCuicappsMIB | 3 | 130 | The Cisco Unified Intelligence Center (CUIC) is a scalable robust and secure reporting solution for contact center applications. T… |
| 1.3.6.1.4.1.9.9.719 | ciscoUnifiedComputingMIB | 5 | 13463 | This MIB module defines the managed objects for Unified Computing System (UCS) Manager. Cisco UCS Manager provides centralized m… |
| 1.3.6.1.4.1.9.9.720 | ciscoTrustSecSxpMIB | 3 | 140 | This MIB module is for the configuration and status query of SGT Exchange Protocol over TCP (SXPoTCP) feature of the device on th… |
| 1.3.6.1.4.1.9.9.721 | ciscoMldSnoopingMIB | 3 | 215 | This MIB module defines objects that describe IGMP/MLD snooping. It provides remote network management system the ability to manag… |
| 1.3.6.1.4.1.9.9.724 | cggsnGeoMIB | 2 | 12 | This MIB provide additional information for passive interface configured for each OSPF process, independent of object creation in… |
| 1.3.6.1.4.1.9.9.725 | ciscoSmartInstallMIB | 3 | 101 | This MIB module defines managed objects that facilitate the management of Smart Install feature. Smart Install is a plug-and-pla… |
| 1.3.6.1.4.1.9.9.729 | ciscoCdstvServicesMIB | 3 | 21 | This MIB module defines service monitoring objects that faciliate the management of the Cisco Content Delivery System for TV (CDS… |
| 1.3.6.1.4.1.9.9.730 | ciscoTrustSecMIB | 3 | 128 | This MIB module is for the configuration of a network device on the Cisco Trusted Security (TrustSec) system. TrustSec secures a … |
| 1.3.6.1.4.1.9.9.731 | ciscoEpcGatewayMIB | 3 | 130 | This MIB module manages the features and configuration for PDN Gateway(PGW) and Serving Gateway(SGW) in Evolved Packet Core(EPC) … |
| 1.3.6.1.4.1.9.9.732 | ciscoDeviceLocationMIB | 3 | 49 | This MIB is used for managing location information of end point devices(Telepresence, IP Camera, Digital media player etc) connec… |
| 1.3.6.1.4.1.9.9.733 | ciscoMeetingPlaceMIB | 3 | 70 | This MIB allows management of Cisco Unified MeetingPlace (CUMP) features, CUMP is the key conferencing solution component for Cis… |
| 1.3.6.1.4.1.9.9.734 | ciscoGtpv2MIB | 2 | 160 | This MIB module manages the GPRS Tunneling Protocol version 2(GTPv2) statistics for the Evolved Packet Core(EPC) architecture. SGW… |
| 1.3.6.1.4.1.9.9.735 | ciscoCdstvFsiMIB | 3 | 25 | This MIB module defines FSI configurartion objects that faciliate the management of the Cisco Content Delivery System for TV (CDS… |
| 1.3.6.1.4.1.9.9.736 | ciscoRadiusExtMIB | 2 | 51 | This MIB module defines objects describing RADIUS (Remote Access Dialin User Service), serving as an extension of the following M… |
| 1.3.6.1.4.1.9.9.737 | ciscoSwitchNetflowMIB | 3 | 40 | This MIB module defines management objects for the Netflow features on Cisco Layer 2 and Layer 3 devices. |
| 1.3.6.1.4.1.9.9.738 | cmplsTeStdExtMIB | 3 | 72 | This MIB module contains Cisco specific managed object definitions for MPLS Traffic Engineering (TE), not contained in MPLS-TE-ST… |
| ... | ||||