The encapsulation that will be used for syslog messages
by the syslog receiver.
If this syslog application is not a syslog receiver the
value of this object will be ''other''.
pwCepIndications OBJECT-TYPE
SYNTAX BITS {
missingPkt ( 0),
ooRngDropped( 1),
jtrBfrUnder ( 2),
pktMalformed( 3),
lops ( 4),
cepRdi ( 5),
cepAis ( 6),
badHdrStack ( 7),
cepNeFailure( 8),
cepFeFailure( 9)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Definitions:
\missingPkt\(0) - While playing out a sequence of packets,
at least one packet was determined to be missing based on a
gap in the CEP sequence number. Note: If the implementation
supports packet reordering, detecting gaps SHOULD take
place as they are played out, not as they arrive. This
provides time for misordered packets to arrive late.
\ooRngDropped\(1) - At least one packet arrived outside the
range of the jitter buffer. This may be because the
jitter buffer is full or the sequence number addresses
a buffer outside the current jitter buffer range or
an already occupied buffer within range. Whether or not
packet reordering is supported by the implementation, this
indication MUST be supported.
\jtrBfrUnder\(2) - The jitter buffer underflowed because
not enough packets arrived as packets were being
played out.
\pktMalformed\(3) - Any error related to unexpected
packet format (except bad header stack) or unexpected
length.
\lops\(4) - Loss of Packet Synchronization.
\cepRdi\(5) - Circuit Emulation over Packet Remote Defect
Indication. Remote Defect Indication (RDI) is generated by
the remote CEP de-packetizer when LOPS is detected.
\cepAis\(6) - Remote CEP packetizer has detected an Alarm
Indication Signal (AIS) on its incoming SONET stream.
cepAis MUST NOT (in itself) cause a CEP PW down
notification.
\badHdrStack\(7) - Set when the number of
CEP header extensions detected in incoming packets does
not match the expected number.
\cepNeFailure\(8) - Set when CEP-NE failure is currently
declared.
\cepFeFailure\(8) - Set when CEP-FE failure is currently
declared.
This object MUST hold the accumulated indications until the
next SNMP write that clear the indication(s).
Writing a non-zero value MUST fail.
Currently, there is no hierarchy of CEP defects.
The algorithm used to capture these indications
is implementation specific."
View at oid-info.com
The encapsulation that will be used for syslog messages
by the syslog receiver.
If this syslog application is not a syslog receiver the
value of this object will be ''other''.
syslogControlEncapsulation OBJECT-TYPE SYNTAX SyslogEncapsulation ACCESS read-write STATUS mandatory DESCRIPTION "The encapsulation that will be used for syslog messages by the syslog receiver. If this syslog application is not a syslog receiver the value of this object will be ''other''." ::= { syslogControlEntry 7 }
Automatically extracted from RFC6240
syslogControlEncapsulation OBJECT-TYPE SYNTAX SyslogEncapsulation MAX-ACCESS read-create STATUS current DESCRIPTION "The encapsulation that will be used for syslog messages by the syslog receiver. If this syslog application is not a syslog receiver the value of this object will be ''other''. " ::= { syslogControlEntry 7 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.200.1.1.1.1 | pwCepType, syslogControlIndex | 0 | 0 | The Index that uniquely identifies the syslog application in the syslogControlTable. The value of the index for a syslog applicat… |
| 1.3.6.1.2.1.200.1.1.1.2 | pwCepSonetIfIndex, syslogControlDescr | 0 | 0 | A user definable description of the syslog application. This description could be used by syslog management applications e.g. in … |
| 1.3.6.1.2.1.200.1.1.1.3 | pwCepSonetConfigErrorOrStatus, syslogControlRoles | 0 | 0 | The roles of the syslog application. |
| 1.3.6.1.2.1.200.1.1.1.4 | pwCepCfgIndex, syslogControlBindAddrType | 0 | 0 | The type of Internet address which follows in syslogControlBindAddr. If this syslog application is not a syslog receiver, the valu… |
| 1.3.6.1.2.1.200.1.1.1.5 | pwCepTimeElapsed, syslogControlBindAddr | 0 | 0 | pwCepTimeElapsed OBJECT-TYPE SYNTAX HCPerftimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The numb… |
| 1.3.6.1.2.1.200.1.1.1.6 | pwCepValidIntervals, syslogControlBindPort | 0 | 0 | The port number that this syslog receiver will bind to. If this syslog application is not a syslog receiver the value of this obj… |
| 1.3.6.1.2.1.200.1.1.1.8 | pwCepLastEsTimeStamp, syslogControlMaxMessageSize | 0 | 0 | The maximum size of the syslog messages in bytes for this syslog application. A syslog receiver may reject or truncate messages l… |
| 1.3.6.1.2.1.200.1.1.1.9 | pwCepPeerCepOption, syslogControlConfFileName | 0 | 0 | pwCepPeerCepOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the CEP option p… |
| 1.3.6.1.2.1.200.1.1.1.11 | syslogControlStorageType | 0 | 0 | This object defines whether the parameters defined in this row are kept in volatile storage and lost upon reboot or are backed up… |
| 1.3.6.1.2.1.200.1.1.1.12 | syslogControlRowStatus | 0 | 0 | This object is used to create, modify and delete rows in the syslogControlTable. The value of syslogControlDescr can be changed wh… |