The delay after going On Battery until the Receptacle is
automatically turned Off. A value of -1 means that this Output should
never be turned Off automatically, but must be turned Off only by command.
Values from 0 to 30 are valid, but probably innappropriate.
The AutoOffDelay can be used to prioritize loads in the event of a prolonged
power outage; less critical loads will turn off earlier to extend battery
time for the more critical loads. If the utility power is restored before the
AutoOff delay counts down to 0 on an outlet, that outlet will not turn Off.
Parsed from file CPQPOWER1.62.MIB.txt
Company: None
Module: CPQPOWER-MIB
The delay after going On Battery until the Receptacle is
automatically turned Off. A value of -1 means that this Output should
never be turned Off automatically, but must be turned Off only by command.
Values from 0 to 30 are valid, but probably innappropriate.
The AutoOffDelay can be used to prioritize loads in the event of a prolonged
power outage; less critical loads will turn off earlier to extend battery
time for the more critical loads. If the utility power is restored before the
AutoOff delay counts down to 0 on an outlet, that outlet will not turn Off.
Parsed from file CPQPOWER-MIB.mib
Module: CPQPOWER-MIB
upsRecepAutoOffDelay OBJECT-TYPE SYNTAX INTEGER (-1..32767) ACCESS read-write STATUS mandatory DESCRIPTION "The delay after going On Battery until the Receptacle is automatically turned Off. A value of -1 means that this Output should never be turned Off automatically, but must be turned Off only by command. Values from 0 to 30 are valid, but probably innappropriate. The AutoOffDelay can be used to prioritize loads in the event of a prolonged power outage; less critical loads will turn off earlier to extend battery time for the more critical loads. If the utility power is restored before the AutoOff delay counts down to 0 on an outlet, that outlet will not turn Off." ::= { upsRecepEntry 5 }
Vendor: Compaq
Module: CPQPOWER-MIB
[Automatically extracted from oidview.com]
upsRecepAutoOffDelay OBJECT-TYPE SYNTAX INTEGER (-1..32767) ACCESS read-write STATUS mandatory DESCRIPTION "The delay after going On Battery until the Receptacle is automatically turned Off. A value of -1 means that this Output should never be turned Off automatically, but must be turned Off only by command. Values from 0 to 30 are valid, but probably innappropriate. The AutoOffDelay can be used to prioritize loads in the event of a prolonged power outage; less critical loads will turn off earlier to extend battery time for the more critical loads. If the utility power is restored before the AutoOff delay counts down to 0 on an outlet, that outlet will not turn Off." ::= { upsRecepEntry 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.232.165.3.10.2.1.1 | upsRecepIndex | 0 | 0 | The number of the Receptacle. Serves as index for Receptacle table. |
| 1.3.6.1.4.1.232.165.3.10.2.1.2 | upsRecepStatus | 0 | 0 | The Recep Status 1=On/Close, 2=Off/Open, 3=On w/Pending Off, 4=Off w/Pending ON, 5=Unknown. |
| 1.3.6.1.4.1.232.165.3.10.2.1.3 | upsRecepOffDelaySecs | 0 | 0 | The Delay until the Receptacle is turned Off. Setting this value to other than -1 will cause the UPS output to turn off after th… |
| 1.3.6.1.4.1.232.165.3.10.2.1.4 | upsRecepOnDelaySecs | 0 | 0 | The Delay until the Receptacle is turned On. Setting this value to other than -1 will cause the UPS output to turn on after the … |
| 1.3.6.1.4.1.232.165.3.10.2.1.6 | upsRecepAutoOnDelay | 0 | 0 | Seconds delay after the Outlet is signaled to turn On before the Output is Automatically turned ON. A value of -1 means that thi… |
| 1.3.6.1.4.1.232.165.3.10.2.1.7 | upsRecepShedSecsWithRestart | 0 | 0 | Setting this value will cause the UPS output to turn off after the set number of seconds, then restart (after a UPS-defined 'down… |