This object defines E&MII Wink Duration. Default = 20, in
10 ms interval. e.g. 20 = 200 ms
Parsed from file RDS1.MIB.txt
Company: cai
Module: RDS1-MIB
Vendor: 3Com
Module: RDS1-MIB (RDS1.MIB)
Type: TABULAR
Access: read-write
Syntax: INTEGER
(
0..255 )
Automatically extracted from www.mibdepot.com
usrds1CfgWink OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This object defines E&MII Wink Duration. Default = 20, in 10 ms interval. e.g. 20 = 200 ms" ::= { usrds1ConfigEntry 39 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.27.1.1.1 | usrds1CfgIndex | 0 | 0 | The index value which uniquely identifies the CSU to which this entry is applicable. This index corresponds to dsx1LineIndex def… |
| 1.3.6.1.4.1.429.1.27.1.1.2 | usrds1CfgRspToRemoteLpbk | 0 | 0 | This object configures the specified CSU to either ignore or respond to remotely initiated loopback requests. |
| 1.3.6.1.4.1.429.1.27.1.1.3 | usrds1CfgJitterAttnution | 0 | 0 | This object is used to select how the jitter attenuation circuit on the CSU is to be used. It can be used to attenuate jitter on… |
| 1.3.6.1.4.1.429.1.27.1.1.4 | usrds1CfgXmitLineBuildOut | 0 | 0 | This object is used to configure the amount of attenuation that is to be applied to the transmit signal in order to control cross… |
| 1.3.6.1.4.1.429.1.27.1.1.5 | usrds1CfgDialInAdr | 0 | 0 | This object identifies whether or not type of MF/DTMF will be transferred as part of the call setup for the specified T1 line. |
| 1.3.6.1.4.1.429.1.27.1.1.6 | usrds1CfgDialInOutTrunkSt | 0 | 0 | This will set the Dial-in/Dial-out trunk start signal type. Default = wink(1). |
| 1.3.6.1.4.1.429.1.27.1.1.7 | usrds1CfgDialInAdrAckWink | 0 | 0 | Allows to enable/disable an acknowledgment wink after the dial-in address information has been received. |
| 1.3.6.1.4.1.429.1.27.1.1.8 | usrds1CfgDialOutAdrDly | 0 | 0 | Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO. |
| 1.3.6.1.4.1.429.1.27.1.1.9 | usrds1CfgDialIOTrunkType | 0 | 0 | This will set the Dial-In/Dial-out trunk type. Default = eAndMTypeII(1). |
| 1.3.6.1.4.1.429.1.27.1.1.10 | usrds1CfgPriSwitchType | 0 | 0 | usrds1CfgPriSwitchtype |
| 1.3.6.1.4.1.429.1.27.1.1.11 | usrds1CfgIdleByte | 0 | 0 | This sets the idle byte pattern for the T1-PRI ISDN NAC. The setting takes effect at NAC boot time. Default = 0xFE. |
| 1.3.6.1.4.1.429.1.27.1.1.12 | usrds1CfgAnlgBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when analog connections are being blocked. Default = 58. |
| 1.3.6.1.4.1.429.1.27.1.1.13 | usrds1CfgDgtlBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when digital connections are being blocked. Default = 58. |
| 1.3.6.1.4.1.429.1.27.1.1.14 | usrds1CfgNoIgwAvailErCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when there are no modems available to accept the requested connect… |
| 1.3.6.1.4.1.429.1.27.1.1.15 | usrds1CfgChanBlockErrCode | 0 | 0 | This is the error code that will be returned to an ISDN switch when connections to a specific B channel are being blocked. Default… |
| 1.3.6.1.4.1.429.1.27.1.1.16 | usrds1CfgBlockCallType | 0 | 0 | This object determines if a PRI span line will block calls of a specific type. This object does not apply to a NAC operating in … |
| 1.3.6.1.4.1.429.1.27.1.1.17 | usrds1CfgShrtHaulDist, usrds1ShrtHaulDist | 0 | 0 | Various distance ranges supported by Short Haul NIC Default=len0thru133Ft. |
| 1.3.6.1.4.1.429.1.27.1.1.18 | usrds1CfgNicCfgType, usrdsx1NicCfgType | 0 | 0 | Type of T1/E1 interface configured - Short haul of long haul. |
| 1.3.6.1.4.1.429.1.27.1.1.19 | usrds1CfgToneType, usrds1ToneType | 0 | 0 | DS1 Tone type (MF/DTMF) - CHT1 only. |
| 1.3.6.1.4.1.429.1.27.1.1.20 | usrds1CfgNumDtmfTones, usrds1NumDtmfTones | 0 | 0 | usrds1CfgNumDtmftones |
| 1.3.6.1.4.1.429.1.27.1.1.21 | usrds1CfgDialOutSlctDirct, usrchT1E1DialOutSlctDirct | 0 | 0 | This object defines whether DS0 are chosen hunting up or down from the currently defined staring DS0. Default=down. |
| 1.3.6.1.4.1.429.1.27.1.1.22 | usrds1CfgDialOutNextDS0, usrchT1E1DialOutNextDS0 | 0 | 0 | This object defines the starting DS0s to do dial-out hunting from. |
| 1.3.6.1.4.1.429.1.27.1.1.23 | usrds1CfgRcvGain | 0 | 0 | This object is used to configure the amount of Receiver Gain that is applied to the received signal at the CSU. T1 Long Haul: 26 … |
| 1.3.6.1.4.1.429.1.27.1.1.24 | usrds1CfgCht1Profile | 0 | 0 | The following object is used to configure profile for channelized T1. Following are the profile setting for each available option… |
| 1.3.6.1.4.1.429.1.27.1.1.25 | usrds1CfgCallProceedngRsp | 0 | 0 | This Object determines to send CALL_PROCEEDING and CONNECT response, when a SETUP message received from TELCO. Default = ON. |
| 1.3.6.1.4.1.429.1.27.1.1.26 | usrds1CfgAlertingRsp | 0 | 0 | This Object determines to send ALERTING response, when a SETUP message is received from TELCO. Default = OFF. |
| 1.3.6.1.4.1.429.1.27.1.1.27 | usrds1CfgOverLapRxMode | 0 | 0 | This Object allows dialed digits to arrive in separate messages. Default=disabled(2). |
| 1.3.6.1.4.1.429.1.27.1.1.28 | usrds1CfgNFASInterfaceId | 0 | 0 | This object indicates external ( assigned by Telco ) interface id. It is one of the entries in the NFAS group table. |
| 1.3.6.1.4.1.429.1.27.1.1.29 | usrds1CfgSigGroupNumber | 0 | 0 | Indicates NFAS ( or SS7 ) logical group number to be monitored ( configured). This variable serves as an index for entering NFAS… |
| 1.3.6.1.4.1.429.1.27.1.1.30 | usrds1CfgNFASSpanType | 0 | 0 | Span type with regard to the D-Channel: Primary, Back-up, None or FAS (the latter in case if NFAS is not configured). It is one o… |
| 1.3.6.1.4.1.429.1.27.1.1.31 | usrds1CfgSigGroupType | 0 | 0 | This variable indicates one of the three possible application types: FAS, NFAS, or FAS. FAS stands for facility associated signal… |
| 1.3.6.1.4.1.429.1.27.1.1.32 | usrds1CfgOutBearerCap | 0 | 0 | Controls the bearer capability for outgoing analog calls. Default=audio3K(1). |
| 1.3.6.1.4.1.429.1.27.1.1.33 | usrds1CfgSs7Mode | 0 | 0 | This object is used to select if the span line is to be controlled by a SS7 device. A value of None indicates that the span line … |
| 1.3.6.1.4.1.429.1.27.1.1.34 | usrds1CfgInfoMsgTimeOut | 0 | 0 | This object sets the time out delay in seconds between INFO message. This parameter is effective if overlap RX mode is enabled. D… |
| 1.3.6.1.4.1.429.1.27.1.1.35 | usrds1CfgInbDNISLength | 0 | 0 | This objects sets the total number of digits expected in the inbound phone number. In the E1-PRI this is only effective when over… |
| 1.3.6.1.4.1.429.1.27.1.1.36 | usrds1CfgAnsDly | 0 | 0 | This object defines E&MII answer supervision delay time. Default = 11, in 10 ms interval. e.g. 1 = 10 ms |
| 1.3.6.1.4.1.429.1.27.1.1.37 | usrds1CfgDiscDeb | 0 | 0 | This object defines E&MII E-lead disc debounce time. Default = 30 in 10 ms interval. e.g 30 = 300 ms |
| 1.3.6.1.4.1.429.1.27.1.1.38 | usrds1CfgSanity | 0 | 0 | This object defines E&MII Telco disc sanity time. Default = 10 sec |
| 1.3.6.1.4.1.429.1.27.1.1.40 | usrds1CfgV42Wan | 0 | 0 | This object defines E&MII V42 to WAN disc delay time. Default = 0. 0-254 in 100 ms intervals, a configuration of 255 is 125 sec. |
| 1.3.6.1.4.1.429.1.27.1.1.41 | usrds1CfgTeldis | 0 | 0 | This object defines E&MII Telco init disc delay time. Default = 0 in 100 ms interval. e.g 1 = 100 ms |
| 1.3.6.1.4.1.429.1.27.1.1.42 | usrds1CfgSeize | 0 | 0 | This object defines E&MII Seizure to Wink delay time. Default = 22, in 10 ms interval. e.g. 22 = 220 ms |
| 1.3.6.1.4.1.429.1.27.1.1.43 | usrds1CfgDSPFailureAction | 0 | 0 | This object tells a DSP what action to take when it detects that neither of its pumps is able to complete a call at the physical … |
| 1.3.6.1.4.1.429.1.27.1.1.44 | usrds1CfgR2AnsHoldTimer | 0 | 0 | This object controls the minimum duration for which the E1 R2 Answer line signal will be transmitted before any other signal is t… |
| 1.3.6.1.4.1.429.1.27.1.1.45 | usrds1CfgHsOnProgMsg | 0 | 0 | This object allows outgoing analog calls over PRI to begin modem handshaking on receipt of a Progress message, instead of waiting… |
| 1.3.6.1.4.1.429.1.27.1.1.46 | usrds1CfgISSMode | 0 | 0 | This object enables or disables the ISS feature that allows message to be passed between an ISS enabled EdgeServer and Siemens EW… |