Set the DS3 loopback mode to line, terminal,
remote, or none. The System can't be set to
ds3LpbkRemoteFacility when it is in M13 Mode.
The Terminal LoopBack is feasible only when the
elCMDS3TxTiming Object is set to ds3TxTimingLocal.
Parsed from file el.mib.txt
Company: None
Module: EDGELINK-MIB
Set the DS3 loopback mode to line, terminal,
remote, or none. The System can't be set to
ds3LpbkRemoteFacility when it is in M13 Mode.
The Terminal LoopBack is feasible only when the
elCMDS3TxTiming Object is set to ds3TxTimingLocal.
Parsed from file EDGELINK-MIB.mib
Module: EDGELINK-MIB
Vendor: Telco Systems NAC
Module: EDGELINK-MIB
[Automatically extracted from oidview.com]
elCMDS3LoopbackMode OBJECT-TYPE SYNTAX INTEGER { ds3LpbkNone(1), ds3LpbkTerminal(2), ds3LpbkFacility(3), ds3LpbkRemoteFacility(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Set the DS3 loopback mode to line, terminal, remote, or none. The System can't be set to ds3LpbkRemoteFacility when it is in M13 Mode. The Terminal LoopBack is feasible only when the elCMDS3TxTiming Object is set to ds3TxTimingLocal." ::= { elCM 8 }
elCMDS3LoopbackMode OBJECT-TYPE SYNTAX INTEGER { ds3LpbkNone(1), ds3LpbkTerminal(2), ds3LpbkFacility(3), ds3LpbkRemoteFacility(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Set the DS3 loopback mode to line, terminal, remote, or none. The System can't be set to ds3LpbkRemoteFacility when it is in M13 Mode. The Terminal LoopBack is feasible only when the elCMDS3TxTiming Object is set to ds3TxTimingLocal." ::= { elCM 8 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.564.101.1.2.8.0 | elCMDS3LoopbackMode | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.564.101.1.2.1 | elCMSystemStatus | 1 | 1 | This DisplayString gives the summary information about the Current EdgeLink100 System Status. The Description includes ... 1) chas… |
| 1.3.6.1.4.1.564.101.1.2.2 | elCMDS3ParityMode | 1 | 1 | Select C-bit or P-bit parity mode for DS3 interface. This Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.3 | elCMDS3LineBuildout | 1 | 1 | Select line build-out for DS3 Line, 0 to 100 ft, 100 to 200 ft, or 200-450.This MIB Object can't be set when ServiceMode is IN-Se… |
| 1.3.6.1.4.1.564.101.1.2.4 | elCMDS3TxTiming | 1 | 1 | Select mode for DS3 transmit timing. This MIB Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.5 | elCMProtectionMode | 1 | 1 | In unprotected mode, switching is prohibited. While in protected mode, a standing minor alarm will occur if the off-line card is … |
| 1.3.6.1.4.1.564.101.1.2.6 | elCMCardSelect | 1 | 1 | Read or select choice of on-line card. This operation will force a switch to occur if the off-line card is selected. |
| 1.3.6.1.4.1.564.101.1.2.7 | elCMClearTooManySwitches | 1 | 1 | Clear switching-disabled state which occurs as a result of too many switches between the cards in a protected system in a 10 minu… |
| 1.3.6.1.4.1.564.101.1.2.9 | elCMDS3ServiceMode | 1 | 1 | Set the DS3 service mode to in-service or out-of-service. Certain service effecting operations can not be initiated unless the DS… |
| 1.3.6.1.4.1.564.101.1.2.10 | elCMCurTimeDate | 1 | 1 | Read or set the system real time clock. The string is in the form MM/DD/YYYY HH:MM:SS. |
| 1.3.6.1.4.1.564.101.1.2.11 | elCMBerThreshold | 1 | 1 | Set the BER Threshold value for the system to 10-6, 10-7, 10-8 or 10-9. BerThershold can't changed when the ServiceMode is IN-Ser… |
| 1.3.6.1.4.1.564.101.1.2.12 | elCMSystemInfo | 1 | 1 | Gets information about the MPU type, board revision, card revision level, software revision, CLEI code, MAC address, and Date of … |
| 1.3.6.1.4.1.564.101.1.2.13 | elCMPPPPortBaudRate | 1 | 1 | Specifies the baud rate on the craft/PPP port when that port is running PPP (i.e. when carrier detect is asserted). |