The percentage of disk space utilization at which excessive
disk utilization (sDskFull) traps begin to be sent. If this
variable is set to a value other than zero, it is used to
determine when to send sDskFull traps for disks not specified
in the critical disk table (see sCfgCritDsk).
This value and sCfgDskMinFreeBlks are mutually exclusive, i.e.,
only one of these values is in effect at any given time. If
neither value is specified in the configuration file, then
the default value of sCfgDskLimit is used for disk monitoring
and sCfgDskMinFreeBlks is set to zero. To disable default
disk full monitoring, both of these values must be zero.
Set-requests to this value will fail unless sCfgDskMinFreeBlks
is set to zero.
Configuration Variable: DskUse
Set-requests: Take effect immediately
Changes to this value are written to the sCfgFile.
Parsed from file NMSYSMGR.MIB.txt
Company: None
Module: COMTEK-VMS-NM-SYSMGR-MIB
The percentage of disk space utilization at which excessive
disk utilization (sDskFull) traps begin to be sent. If this
variable is set to a value other than zero, it is used to
determine when to send sDskFull traps for disks not specified
in the critical disk table (see sCfgCritDsk).
This value and sCfgDskMinFreeBlks are mutually exclusive, i.e.,
only one of these values is in effect at any given time. If
neither value is specified in the configuration file, then
the default value of sCfgDskLimit is used for disk monitoring
and sCfgDskMinFreeBlks is set to zero. To disable default
disk full monitoring, both of these values must be zero.
Set-requests to this value will fail unless sCfgDskMinFreeBlks
is set to zero.
Configuration Variable: DskUse
Set-requests: Take effect immediately
Changes to this value are written to the sCfgFile.
Parsed from file COMTEK-VMS-NM-SYSMGR-MIB.mib
Module: COMTEK-VMS-NM-SYSMGR-MIB
Vendor: Comtek Services Inc.
Module: COMTEK-VMS-NM-SYSMGR-MIB
[Automatically extracted from oidview.com]
sCfgDskLimit OBJECT-TYPE SYNTAX INTEGER (0..100) ACCESS read-write STATUS mandatory DESCRIPTION "The percentage of disk space utilization at which excessive disk utilization (sDskFull) traps begin to be sent. If this variable is set to a value other than zero, it is used to determine when to send sDskFull traps for disks not specified in the critical disk table (see sCfgCritDsk). This value and sCfgDskMinFreeBlks are mutually exclusive, i.e., only one of these values is in effect at any given time. If neither value is specified in the configuration file, then the default value of sCfgDskLimit is used for disk monitoring and sCfgDskMinFreeBlks is set to zero. To disable default disk full monitoring, both of these values must be zero. Set-requests to this value will fail unless sCfgDskMinFreeBlks is set to zero. Configuration Variable: DskUse Set-requests: Take effect immediately Changes to this value are written to the sCfgFile." DEFVAL { 90 } ::= { sCfg 10 }
sCfgDskLimit OBJECT-TYPE SYNTAX INTEGER (0..100) ACCESS read-write STATUS mandatory DESCRIPTION "The percentage of disk space utilization at which excessive disk utilization (sDskFull) traps begin to be sent. If this variable is set to a value other than zero, it is used to determine when to send sDskFull traps for disks not specified in the critical disk table (see sCfgCritDsk). This value and sCfgDskMinFreeBlks are mutually exclusive, i.e., only one of these values is in effect at any given time. If neither value is specified in the configuration file, then the default value of sCfgDskLimit is used for disk monitoring and sCfgDskMinFreeBlks is set to zero. To disable default disk full monitoring, both of these values must be zero. Set-requests to this value will fail unless sCfgDskMinFreeBlks is set to zero. Configuration Variable: DskUse Set-requests: Take effect immediately Changes to this value are written to the sCfgFile." DEFVAL { 90 } ::= { sCfg 10 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.597.4.3.5.10.0 | sCfgDskLimit | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.597.4.3.5.1 | sCfgFile | 1 | 1 | Name of the file currently being used for NM*SysMgr initialization parameters. This file is identified by the logical name COMTE… |
| 1.3.6.1.4.1.597.4.3.5.2 | sCfgLogFile | 1 | 1 | Name of the log file currently being used by NM*SysMgr. If this process is run interactively, this variable will have the value S… |
| 1.3.6.1.4.1.597.4.3.5.3 | sCfgCritFile | 1 | 1 | Name of the file currently being used to identify critical processes. This file is associated with the logical name COMTEK$SYSMGR… |
| 1.3.6.1.4.1.597.4.3.5.4 | sCfgReinitSubagent | 1 | 1 | Flag which may be set to force the NM*SysMgr Subagent to reinitialize. Reinitialization involves resetting the process configura… |
| 1.3.6.1.4.1.597.4.3.5.5 | sCfgTraps | 1 | 1 | Flag which determines if any trap messages are sent to the NM*Master Agent. Setting this variable to disabled(2) disables all tr… |
| 1.3.6.1.4.1.597.4.3.5.6 | sCfgHwErrTraps | 1 | 1 | Flag which determines if hardware error traps (sHwErr) should be sent. Setting this variable to enabled(1) causes a trap to be s… |
| 1.3.6.1.4.1.597.4.3.5.7 | sCfgCpuLimit | 1 | 1 | The percentage of CPU utilization at which excessive CPU utilization (sCpuUsage) traps begin to be sent. A value of 0 disables th… |
| 1.3.6.1.4.1.597.4.3.5.8 | sCfgIntLimit | 1 | 1 | The percentage of interrupt CPU utilization at which excessive interrupt utilization (sIntUsage) traps begin to be sent. A value… |
| 1.3.6.1.4.1.597.4.3.5.9 | sCfgDskOps | 1 | 1 | The threshold at which excessive disk busy traps (sDskOpSec) begin to be sent. This value is expressed in terms of disk operatio… |
| 1.3.6.1.4.1.597.4.3.5.11 | sCfgPgLimit | 1 | 1 | The percentage of page file utilization at which excessive page file utilization (sPgFull) traps begin to be sent. A value of 0 d… |
| 1.3.6.1.4.1.597.4.3.5.12 | sCfgSwpLimit | 1 | 1 | The percentage of swap file utilization at which excessive swap file utilization (sSwpFull) traps begin to be sent. A value of 0 … |
| 1.3.6.1.4.1.597.4.3.5.13 | sCfgPsTimer | 1 | 1 | The number of minutes between updates of the process statistics table (sPsTbl) data. A value of 0 disables gathering of process … |
| 1.3.6.1.4.1.597.4.3.5.14 | sCfgDskTimer | 1 | 1 | The number of minutes between updates of the disk table (sDskTbl) data. A value of 0 disables gathering of disk related data. Con… |
| 1.3.6.1.4.1.597.4.3.5.15 | sCfgHwErrTimer | 1 | 1 | The number of minutes between updates of the hardware error table (sHwErrTbl) data. A value of 0 disables gathering of hardware … |
| 1.3.6.1.4.1.597.4.3.5.16 | sCfgSysInfoTimer | 1 | 1 | The number of minutes between updates of the system information (sSyi) data. A value of 0 disables gathering of system informati… |
| 1.3.6.1.4.1.597.4.3.5.17 | sCfgCritTimer | 1 | 1 | The number of minutes between critical process table (sCritTbl) updates. A value of 0 disables critical process missing processi… |
| 1.3.6.1.4.1.597.4.3.5.18 | sCfgDskAlarm | 1 | 1 | The number of minutes between repeat traps for disk (sDskFull), page file (sPgFull), or swap file full (sSwpFull) conditions. A v… |
| 1.3.6.1.4.1.597.4.3.5.19 | sCfgCritAlarm | 1 | 1 | The number of minutes between repeat traps for a given critical process missing condition. Setting this variable to 0 causes onl… |
| 1.3.6.1.4.1.597.4.3.5.20 | sCfgTrapTblSize | 1 | 1 | The maximum number of traps to be retained. Traps that are retained may be resent (see sTrapResendSeqNum) unless too many subseq… |
| 1.3.6.1.4.1.597.4.3.5.21 | sCfgHostName | 1 | 1 | The name of the host that the subagent is communicating with. This is the host name where the NM*Master Agent resides. This varia… |
| 1.3.6.1.4.1.597.4.3.5.22 | sCfgAllPsData | 1 | 1 | This variable controls the amount of data that is available in the process statistics table (sPsTbl). If this flag is set to no(… |
| 1.3.6.1.4.1.597.4.3.5.23 | sCfgTimeout | 1 | 1 | This variable identifies the time-out value that is to be used by the subagent during subtree registration. If this value is set… |
| 1.3.6.1.4.1.597.4.3.5.24 | sCfgOpcomSecurity | 1 | 1 | Flag which determines if the opcom security messages are to be sent as opcom traps. Setting this variable to enabled(1) causes o… |
| 1.3.6.1.4.1.597.4.3.5.25 | sCfgControlTermProc | 1 | 1 | Flag which may be used to disable process termination by the sCfgTermProc variable. Setting this variable to enabled(1) allows t… |
| 1.3.6.1.4.1.597.4.3.5.26 | sCfgTermProc | 1 | 1 | Flag which may be used to shutdown the NM*SysMgr process. Setting this flag to true causes the NM*SysMgr process to respond to th… |
| 1.3.6.1.4.1.597.4.3.5.27 | sCfgVersion | 1 | 1 | Current version of the NM*SysMgr Subagent software. |
| 1.3.6.1.4.1.597.4.3.5.28 | sCfgUpTime | 1 | 1 | Subagent up time. |
| 1.3.6.1.4.1.597.4.3.5.29 | sCfgMaxTrapSec | 1 | 1 | This value specifies the maximum number of traps per second that may be sent. A value of zero disables trap throttling, allowing… |
| 1.3.6.1.4.1.597.4.3.5.30 | sCfgCritDsk | 1 | 1 | Name of the file currently being used to identify critical disk space and operations per second trap thresholds for individual di… |
| 1.3.6.1.4.1.597.4.3.5.31 | sCfgCritQue | 1 | 1 | Name of the file currently being used to identify queues to be monitored. This file is associated with the logical name COMTEK$S… |
| 1.3.6.1.4.1.597.4.3.5.32 | sCfgQueTimer | 1 | 1 | The number of minutes between updates of the queue statistics table (sQTbl) data. A value of 0 disables gathering of queue relat… |
| 1.3.6.1.4.1.597.4.3.5.33 | sCfgDskMinFreeBlks | 1 | 1 | The minimum number of disk blocks that must be free on a disk. When the number of free blocks on a disk drops below this level, … |
| 1.3.6.1.4.1.597.4.3.5.34 | sCfgMemLimit | 1 | 1 | The percentage of physical memory utilization at which excessive memory utilization (sMemFull) traps begin to be sent. A value of… |
| 1.3.6.1.4.1.597.4.3.5.35 | sCfgCOMQueueLimit | 1 | 1 | The number of processes in COM state at which excessive compute queue (sCOMQue) traps begin to be sent. A value of 0 disables the… |
| 1.3.6.1.4.1.597.4.3.5.36 | sCfgCOMOQueueLimit | 1 | 1 | The number of processes in COMO state at which excessive outswapped compute queue (sCOMOQue) traps begin to be sent. A value of 0… |
| 1.3.6.1.4.1.597.4.3.5.37 | sCfgOpcomCards | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom CARDS class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.38 | sCfgOpcomCentral | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom CENTRAL class messages. Setting this variable to disabled(2) disables NM*S… |
| 1.3.6.1.4.1.597.4.3.5.39 | sCfgOpcomCluster | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom CLUSTERclass messages. Setting this variable to disabled(2) disables NM*Sy… |
| 1.3.6.1.4.1.597.4.3.5.40 | sCfgOpcomDevices | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom DEVICES class messages. Setting this variable to disabled(2) disables NM*S… |
| 1.3.6.1.4.1.597.4.3.5.41 | sCfgOpcomDisks | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom DISKS class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.42 | sCfgOpcomLicense | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom LICENSE class messages. Setting this variable to disabled(2) disables NM*S… |
| 1.3.6.1.4.1.597.4.3.5.43 | sCfgOpcomNetwork | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom NETWORK class messages. Setting this variable to disabled(2) disables NM*S… |
| 1.3.6.1.4.1.597.4.3.5.44 | sCfgOpcomOper1 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER1 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.45 | sCfgOpcomOper2 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER2 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.46 | sCfgOpcomOper3 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER3 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.47 | sCfgOpcomOper4 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER4 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.48 | sCfgOpcomOper5 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER5 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.49 | sCfgOpcomOper6 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER6 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.50 | sCfgOpcomOper7 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER7 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.51 | sCfgOpcomOper8 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER8 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.52 | sCfgOpcomOper9 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER9 class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.53 | sCfgOpcomOper10 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER10 class messages. Setting this variable to disabled(2) disables NM*Sy… |
| 1.3.6.1.4.1.597.4.3.5.54 | sCfgOpcomOper11 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER11 class messages. Setting this variable to disabled(2) disables NM*Sy… |
| 1.3.6.1.4.1.597.4.3.5.55 | sCfgOpcomOper12 | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom OPER12 class messages. Setting this variable to disabled(2) disables NM*Sy… |
| 1.3.6.1.4.1.597.4.3.5.56 | sCfgOpcomPrinter | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom PRINTER class messages. Setting this variable to disabled(2) disables NM*S… |
| 1.3.6.1.4.1.597.4.3.5.57 | sCfgOpcomTapes | 1 | 1 | Flag which determines if NM*SysMgr will receive opcom TAPES class messages. Setting this variable to disabled(2) disables NM*Sys… |
| 1.3.6.1.4.1.597.4.3.5.58 | sCfgOpcomFilter | 1 | 1 | Flag which determines if NM*SysMgr will drop opcom messages that match filter criteria or drop all opcom messages except those t… |
| 1.3.6.1.4.1.597.4.3.5.59 | sCfgLocalDisksOnly | 1 | 1 | Flag which may be used to instruct NM*SysMgr to gather disk statistics either on all available disks or only on local disks. A di… |
| 1.3.6.1.4.1.597.4.3.5.60 | sCfgCritDisksOnly | 1 | 1 | Flag which may be used to instruct NM*SysMgr to gather disk statistics either on all available disks or only on disks listed in t… |