This variable indicates the
Line Status of the interface.
It contains loopback state information
and failure state information.
The dsx3LineStatus is a bit map represented
as a sum, therefore,
it can represent multiple failures
and a loopback (see dsx3LoopbackConfig object
for the type of loopback)
simultaneously.
The dsx3NoAlarm should be set if and only if
no other flag is set.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
Parsed from file RFC1407-MIB.mib
Module: RFC1407-MIB
This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a sum, therefore, it
can represent multiple failures and a loopback
(see dsx3LoopbackConfig object for the type of
loopback) simultaneously. The dsx3NoAlarm must be
set if and only if no other flag is set.
If the dsx3loopbackState bit is set, the loopback
in effect can be determined from the
dsx3loopbackConfig object.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
1024 dsx3UnavailSigState Near End in Unavailable Signal
State
2048 dsx3NetEquipOOS Carrier Equipment Out of Service
dsx3LineStatus OBJECT-TYPE
SYNTAX INTEGER (1..4095)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a sum, therefore, it
can represent multiple failures and a loopback
(see dsx3LoopbackConfig object for the type of
loopback) simultaneously. The dsx3NoAlarm must be
set if and only if no other flag is set.
If the dsx3loopbackState bit is set, the loopback
in effect can be determined from the
dsx3loopbackConfig object.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
1024 dsx3UnavailSigState Near End in Unavailable Signal
State
2048 dsx3NetEquipOOS Carrier Equipment Out of Service"
View at oid-info.com
This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a sum, therefore, it
can represent multiple failures and a loopback
(see dsx3LoopbackConfig object for the type of
loopback) simultaneously. The dsx3NoAlarm must be
set if and only if no other flag is set.
If the dsx3loopbackState bit is set, the loopback
in effect can be determined from the
dsx3loopbackConfig object.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
1024 dsx3UnavailSigState Near End in Unavailable Signal
State
2048 dsx3NetEquipOOS Carrier Equipment Out of Service
Parsed from file mib_txt_12_3_1_5.txt
Company: None
Module: ACC-MIB
This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a sum, therefore, it
can represent multiple failures and a loopback
(see dsx3LoopbackConfig object for the type of
loopback) simultaneously. The dsx3NoAlarm must be
set if and only if no other flag is set.
If the dsx3loopbackState bit is set, the loopback
in effect can be determined from the
dsx3loopbackConfig object.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
1024 dsx3UnavailSigState Near End in Unavailable Signal
State
2048 dsx3NetEquipOOS Carrier Equipment Out of Service
dsx3LineStatus OBJECT-TYPE SYNTAX INTEGER (1..1023) ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback state information and failure state information. The dsx3LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures and a loopback (see dsx3LoopbackConfig object for the type of loopback) simultaneously. The dsx3NoAlarm should be set if and only if no other flag is set. The various bit positions are: 1 dsx3NoAlarm No alarm present 2 dsx3RcvRAIFailure Receiving Yellow/Remote Alarm Indication 4 dsx3XmitRAIAlarm Transmitting Yellow/Remote Alarm Indication 8 dsx3RcvAIS Receiving AIS failure state 16 dsx3XmitAIS Transmitting AIS 32 dsx3LOF Receiving LOF failure state 64 dsx3LOS Receiving LOS failure state 128 dsx3LoopbackState Looping the received signal 256 dsx3RcvTestCode Receiving a Test Pattern 512 dsx3OtherFailure any line status not defined here" ::= { dsx3ConfigEntry 10 }
dsx3LineStatus OBJECT-TYPE SYNTAX INTEGER(1..4095) ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback state information and failure state information. The dsx3LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures and a loopback (see dsx3LoopbackConfig object for the type of loopback) simultaneously. The dsx3NoAlarm must be set if and only if no other flag is set. If the dsx3loopbackState bit is set, the loopback in effect can be determined from the dsx3loopbackConfig object. The various bit positions are: 1 dsx3NoAlarm No alarm present 2 dsx3RcvRAIFailure Receiving Yellow/Remote Alarm Indication 4 dsx3XmitRAIAlarm Transmitting Yellow/Remote Alarm Indication 8 dsx3RcvAIS Receiving AIS failure state 16 dsx3XmitAIS Transmitting AIS 32 dsx3LOF Receiving LOF failure state 64 dsx3LOS Receiving LOS failure state 128 dsx3LoopbackState Looping the received signal 256 dsx3RcvTestCode Receiving a Test Pattern 512 dsx3OtherFailure any line status not defined here 1024 dsx3UnavailSigState Near End in Unavailable Signal State 2048 dsx3NetEquipOOS Carrier Equipment Out of Service" ::= { dsx3ConfigEntry 10 }
Automatically extracted from Cisco "SNMP v2 MIBs".
dsx3LineStatus OBJECT-TYPE SYNTAX INTEGER (1..1023) ACCESS read-only STATUS mandatory ::= { dsx3ConfigEntry 10 }
dsx3LineStatus OBJECT-TYPE SYNTAX INTEGER (1..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback state information and failure state information. The dsx3LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures and a loopback (see dsx3LoopbackConfig object for the type of loopback) simultaneously. The dsx3NoAlarm must be set if and only if no other flag is set. If the dsx3loopbackState bit is set, the loopback in effect can be determined from the dsx3loopbackConfig object. The various bit positions are: 1 dsx3NoAlarm No alarm present 2 dsx3RcvRAIFailure Receiving Yellow/Remote Alarm Indication 4 dsx3XmitRAIAlarm Transmitting Yellow/Remote Alarm Indication 8 dsx3RcvAIS Receiving AIS failure state 16 dsx3XmitAIS Transmitting AIS 32 dsx3LOF Receiving LOF failure state 64 dsx3LOS Receiving LOS failure state 128 dsx3LoopbackState Looping the received signal 256 dsx3RcvTestCode Receiving a Test Pattern 512 dsx3OtherFailure any line status not defined here 1024 dsx3UnavailSigState Near End in Unavailable Signal State 2048 dsx3NetEquipOOS Carrier Equipment Out of Service" ::= { dsx3ConfigEntry 10 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.30.5.1.1 | dsx3LineIndex | 0 | 0 | This object is the identifier of a DS3/E3 Interface on a managed device. If there is an ifEntry that is directly associated with… |
| 1.3.6.1.2.1.10.30.5.1.2 | dsx3IfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.2.1.10.30.5.1.3 | dsx3TimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the near end current error- measurement period. |
| 1.3.6.1.2.1.10.30.5.1.4 | dsx3ValidIntervals | 0 | 0 | The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brou… |
| 1.3.6.1.2.1.10.30.5.1.5 | dsx3LineType | 0 | 0 | This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the… |
| 1.3.6.1.2.1.10.30.5.1.6 | dsx3LineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its charac… |
| 1.3.6.1.2.1.10.30.5.1.7 | dsx3SendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS3/E3 interface by the device. (These are optional for E3 in… |
| 1.3.6.1.2.1.10.30.5.1.8 | dsx3CircuitIdentifier | 0 | 0 | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.2.1.10.30.5.1.9 | dsx3LoopbackConfig | 0 | 0 | This variable represents the loopback configuration of the DS3/E3 interface. The values mean: dsx3NoLoop Not in the loopback state.… |
| 1.3.6.1.2.1.10.30.5.1.11 | dsx3TransmitClockSource | 0 | 0 | The source of Transmit Clock. is derived from the recovered receive clock of another DS3 interface. |
| 1.3.6.1.2.1.10.30.5.1.12 | dsx3InvalidIntervals | 0 | 0 | The number of intervals for which no valid data is available. |
| 1.3.6.1.2.1.10.30.5.1.13 | dsx3LineLength | 0 | 0 | The length of the ds3 line in meters. This object provides information for line build out circuitry if it exists and can use thi… |
| 1.3.6.1.2.1.10.30.5.1.14 | dsx3LineStatusLastChange | 0 | 0 | The value of MIB II's sysUpTime object at the time this DS3/E3 entered its current line status state. If the current state was e… |
| 1.3.6.1.2.1.10.30.5.1.15 | dsx3LineStatusChangeTrapEnable | 0 | 0 | Indicates whether dsx3LineStatusChange traps should be generated for this interface. |
| 1.3.6.1.2.1.10.30.5.1.16 | dsx3LoopbackStatus | 0 | 0 | This variable represents the current state of the loopback on the DS3 interface. It contains information about loopbacks establi… |
| 1.3.6.1.2.1.10.30.5.1.17 | dsx3Channelization | 0 | 0 | Indicates whether this ds3/e3 is channelized or unchannelized. The value of enabledDs1 indicates that this is a DS3 channelized … |
| 1.3.6.1.2.1.10.30.5.1.18 | dsx3Ds1ForRemoteLoop | 0 | 0 | Indicates which ds1/e1 on this ds3/e3 will be indicated in the remote ds1 loopback request. A value of 0 means no DS1 will be lo… |