Defines the timezone where the Annex resides in
minutes west of GMT.
This MIB object corresponds to the NA/admin
Annex parameter 'timezone_minuteswest'.
Parsed from file xylo-anx.mib.txt
Company: None
Module: XYLO-ANNEX-MIB
Defines the timezone where the Annex resides in
minutes west of GMT.
Parsed from file ANNEX-MIB.mib
Module: ANNEX-MIB
Vendor: Xylogics, Inc.
Module: ANNEX-MIB
[Automatically extracted from oidview.com]
anxTimeZone OBJECT-TYPE SYNTAX INTEGER (-720..720) ACCESS read-write STATUS mandatory DESCRIPTION "Defines the timezone where the Annex resides in minutes west of GMT. This MIB object corresponds to the NA/admin Annex parameter 'timezone_minuteswest'." ::= { annexconfig 39 }
anxTimeZone OBJECT-TYPE SYNTAX INTEGER (-1200..1200) ACCESS read-write STATUS mandatory DESCRIPTION "Defines the timezone where the Annex resides in minutes west of GMT." ::= { annexconfig 39 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.15.2.5.39.0 | anxTimeZone | 0 | 0 | None |
To many brothers! Only 100 nearest brothers are shown.
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
... | ||||
1.3.6.1.4.1.15.2.5.1 | anxInetAddr | 1 | 1 | The Internet address of the Annex. |
1.3.6.1.4.1.15.2.5.2 | anxPrefLoadAddr | 1 | 1 | The preferred load address for the Annex. |
1.3.6.1.4.1.15.2.5.3 | anxPrefDumpAddr | 1 | 1 | The preferred dump address for the Annex. |
1.3.6.1.4.1.15.2.5.4 | anxLoadDumpGateway | 1 | 1 | The Internet address of a gateway used when the preferred load or dump host is on a different network or subnet. |
1.3.6.1.4.1.15.2.5.5 | anxLoadDumpSeq | 1 | 1 | Lists the available network interfaces and the order that the Annex uses them when doing a down-line load or up-line dump. |
1.3.6.1.4.1.15.2.5.6 | anxLoadBcast | 1 | 1 | This parameter defines whether the Annex broadcasts for the config or the motd files if they were not found on the preferred load … |
1.3.6.1.4.1.15.2.5.7 | anxServerCap | 1 | 1 | Defines whether the Annex can act as a file server host for another Annex. The allowable values are 'all', 'none' (the default), … |
1.3.6.1.4.1.15.2.5.8 | anxTimeBcast | 1 | 1 | This parameter defines whether the Annex broadcasts for the time if the preferred load host does not provide a time server. |
1.3.6.1.4.1.15.2.5.9 | anxBcastAddr | 1 | 1 | The Internet address used by the Annex when sending broadcasts. |
1.3.6.1.4.1.15.2.5.10 | anxSubnetMask | 1 | 1 | The Internet subnet mask. |
1.3.6.1.4.1.15.2.5.11 | anxAuthAgent | 1 | 1 | This parameter controls whether the Annex can send an ICMP Address Mask Reply to a received ICMP Address Mask Request. |
1.3.6.1.4.1.15.2.5.12 | anxMaxVcli | 1 | 1 | The maximum number of virtual CLI connections allowed by the Annex at any one time. 0 means the Annex does not allow VCLI connec… |
1.3.6.1.4.1.15.2.5.13 | anxIpEncapType | 1 | 1 | This parameter specifies whether the Annex encapsulates IP packets in the Ethernet format or the IEEE 802.2/802.3 Data Link Layer… |
1.3.6.1.4.1.15.2.5.14 | anxNameServer1Type | 1 | 1 | The name service type used by the primary nameserver host. |
1.3.6.1.4.1.15.2.5.15 | anxNameServer1Addr | 1 | 1 | The Internet address of the primary nameserver host. |
1.3.6.1.4.1.15.2.5.16 | anxNameServer2Type | 1 | 1 | The name service type used by the secondary nameserver host. |
1.3.6.1.4.1.15.2.5.17 | anxNameServer2Addr | 1 | 1 | The Internet address of the secondary nameserver host. |
1.3.6.1.4.1.15.2.5.18 | anxNameServerBcast | 1 | 1 | This parameter controls whether the Annex broadcasts a name server request if the preferred name servers do not respond. |
1.3.6.1.4.1.15.2.5.19 | anxRwhod | 1 | 1 | Defines whether the Annex listens for RWHO broadcasts when building its host table. |
1.3.6.1.4.1.15.2.5.20 | anxMinUniqueHostNames | 1 | 1 | Defines whether the Annex minimum uniqueness feature is available. |
1.3.6.1.4.1.15.2.5.21 | anxHostTableSize | 1 | 1 | Defines the number of entries in the Annex host table. 0 indicates no host table. 251 sets no limit on the size of the table. |
1.3.6.1.4.1.15.2.5.22 | anxRouted | 1 | 1 | Defines whether the RIP-listener of the routing daemon on the Annex is enabled. |
1.3.6.1.4.1.15.2.5.23 | anxEnableSecurity | 1 | 1 | This parameter controls whether the Annex security system is enabled. |
1.3.6.1.4.1.15.2.5.24 | anxPassword | 1 | 1 | Setting this parameter changes the Annex's administration password. Reading this parameter will return either |
1.3.6.1.4.1.15.2.5.25 | anxSecurServer1Addr | 1 | 1 | The Internet address of the primary host where the Annex sends its security requests. |
1.3.6.1.4.1.15.2.5.26 | anxSecurServer2Addr | 1 | 1 | The Internet address of the secondary host where the Annex sends its security requests. |
1.3.6.1.4.1.15.2.5.27 | anxNetTurnAround | 1 | 1 | The amount of time (in seconds) that the Annex waits for a response from a security server. |
1.3.6.1.4.1.15.2.5.28 | anxSecurBcast | 1 | 1 | This parameter controls whether the Annex will broadcast its security requests when neither of the preferred security servers are… |
1.3.6.1.4.1.15.2.5.29 | anxVcliSecurity | 1 | 1 | This parameter controls whether the Annex performs user validation on the virtual CLI connections. |
1.3.6.1.4.1.15.2.5.30 | anxVcliPassword | 1 | 1 | This parameter defines a password used by the Annex when setting up a virtual CLI connection. |
1.3.6.1.4.1.15.2.5.31 | anxAcpKey | 1 | 1 | This parameter defines the Annex's encryption key used when exchanging messages between the Annex and the security server. |
1.3.6.1.4.1.15.2.5.32 | anxSysLogMask | 1 | 1 | Defines the priority levels of events logged in the Annex syslog file. The allowable values are 'all', 'none', or one or more of t… |
1.3.6.1.4.1.15.2.5.33 | anxSysLogFacility | 1 | 1 | This parameter defines the 4.3BSD syslog facility used in logging the Annex messages. |
1.3.6.1.4.1.15.2.5.34 | anxSysLogHost | 1 | 1 | The Internet address of the host configured to log Annex messages. |
1.3.6.1.4.1.15.2.5.35 | anxCliPrompt | 1 | 1 | The string used by the Annex to prompt all CLI users. |
1.3.6.1.4.1.15.2.5.36 | anxMotdFile | 1 | 1 | The host file name that contains the message-of-the-day for the Annex. |
1.3.6.1.4.1.15.2.5.37 | anxTftpDirName | 1 | 1 | Specifies the directory name to be prepended to all files (boot image, motd, macros, etc.) when booting via TFTP. |
1.3.6.1.4.1.15.2.5.38 | anxTftpDumpName | 1 | 1 | The full pathname of the TFTP dump file, if any. |
1.3.6.1.4.1.15.2.5.40 | anxDaylightSavings | 1 | 1 | Defines the daylight savings time for the geographic location of the Annex. |
1.3.6.1.4.1.15.2.5.41 | anxLatKey | 1 | 1 | The Annex specific LAT key used to enable or disable the LAT protocol. |
1.3.6.1.4.1.15.2.5.42 | anxCircuitTimer | 1 | 1 | The time interval in tens of milliseconds between the transmission of LAT packets. |
1.3.6.1.4.1.15.2.5.43 | anxFacilityNum | 1 | 1 | The LAT facility number. |
1.3.6.1.4.1.15.2.5.44 | anxLatGroupVal | 1 | 1 | The Annex LAT group code for permitting access to LAT services. To access a specific LAT service, the Annex must have at least o… |
1.3.6.1.4.1.15.2.5.45 | anxKeepAliveTimer | 1 | 1 | The time interval, in seconds, between the transmission of identification packets during times of network inactivity. |
1.3.6.1.4.1.15.2.5.46 | anxReXmitLimit | 1 | 1 | The number of times to retransmit a packet before notifying the user of a network failure. |
1.3.6.1.4.1.15.2.5.47 | anxServerName | 1 | 1 | A string of up to 16 characters used to name the Annex in the LAT protocol. |
1.3.6.1.4.1.15.2.5.48 | anxServiceLimit | 1 | 1 | This parameter defines the upper bound on the number of services that the Annex can maintain in its local service table. |
1.3.6.1.4.1.15.2.5.49 | anxConfigFile | 1 | 1 | The name of the host file that contains the alias and menu entries. |
1.3.6.1.4.1.15.2.5.50 | anxLatVcliGroupVal | 1 | 1 | This Annex parameter specifies which remote group codes are accessible to virtual cli users. All virtual cli users have the same … |
1.3.6.1.4.1.15.2.5.51 | anxLatQueueMax | 1 | 1 | Defines the maximum number of host requests (HIC's) that the Annex will save in its internal queue when the requested resource is… |
1.3.6.1.4.1.15.2.5.52 | anxLatLocation | 1 | 1 | A string of up to 32 characters used to identify the location of the Annex for the LAT protocol. |
1.3.6.1.4.1.15.2.5.53 | anxDisabledModules | 1 | 1 | Defines which selectable modules are currently disabled. The allowable values are 'all', 'none' or one or more of the following n… |
1.3.6.1.4.1.15.2.5.54 | anxSysLogPort | 1 | 1 | Specifies the Annex port number where syslog messages are sent. If set to 0, syslog messages are not sent to an Annex port. Thi… |
1.3.6.1.4.1.15.2.5.55 | anxOptionKey | 1 | 1 | The Annex specific software option key used to enable or disable the AppleTalk, dynamic routing and TN3270 support. This MIB obje… |
1.3.6.1.4.1.15.2.5.56 | anxIpFwdBcast | 1 | 1 | When enabled, all broadcasted IP packets are forwarded to all interfaces. This MIB object corresponds to the NA/admin Annex param… |
1.3.6.1.4.1.15.2.5.57 | anxLooseSrcRoute | 1 | 1 | When enabled, the Annex allows internet loose source routing. This MIB object corresponds to the NA/admin Annex parameter 'loose_… |
1.3.6.1.4.1.15.2.5.58 | anxAppleTalkRouter | 1 | 1 | The Ethernet address of the AppleTalk router. The default value is 0-0-0-0-0-0. Each part of the address must be a hex value sep… |
1.3.6.1.4.1.15.2.5.59 | anxAppleTalkDefZones | 1 | 1 | The comma separated list of AppleTalk zone names used as a default when ACP cannot supply the actual set of zone names. Commas, … |
1.3.6.1.4.1.15.2.5.60 | anxAppleTalkNodeId | 1 | 1 | The AppleTalk node ID that the Annex first tries to use at startup. The address consists of two parts separated by a dot. The a… |
1.3.6.1.4.1.15.2.5.61 | anxAppleTalkZone | 1 | 1 | The zone name that the Annex first tries to use at startup. Spaces and double quotes can be used in the zone name by preceding t… |
1.3.6.1.4.1.15.2.5.62 | anxRipRouteList | 1 | 1 | A list of one to eight IP addresses in dotted address format (ddd.ddd.ddd.ddd) with comma separators between the addresses. This… |
1.3.6.1.4.1.15.2.5.63 | anxRipAuth | 1 | 1 | This is a clear text password that is used to authenticate the RIP packets. If the NULL string is specified, RIP packet authenti… |
1.3.6.1.4.1.15.2.5.64 | anxTcpKeepAlive | 1 | 1 | The default keep-alive value in minutes for connections to this Annex. If this is zero, use the default value of 120 minutes. I… |
1.3.6.1.4.1.15.2.5.65 | anxMaxModemCalls | 1 | 1 | The number of calls for which modem call accounting information is kept. The default value is 20. |
1.3.6.1.4.1.15.2.5.66 | anxOutputTtl | 1 | 1 | The value that is placed in the ttl field of all locally generated IP packets. The default value is 64. This MIB object correspo… |
1.3.6.1.4.1.15.2.5.67 | anxSessionLimit | 1 | 1 | The maximum number of sessions allowed on the Annex. The default is 1152. The maximum value that can be set is actually 16 time… |
1.3.6.1.4.1.15.2.5.68 | anxLockEnable | 1 | 1 | When enabled, allows any port user to use the LOCK DECServer command. The default value is enabled. This MIB object corresponds … |
1.3.6.1.4.1.15.2.5.69 | anxPasswdLimit | 1 | 1 | Defines the maximum number of times a user on a port can attempt to enter a password before the Annex resets the port. Setting t… |
1.3.6.1.4.1.15.2.5.70 | anxLatMulticastTimer | 1 | 1 | The elapsed time in seconds between transmission of service announcements. The default value is 30 seconds. This MIB object corre… |
1.3.6.1.4.1.15.2.5.71 | anxChapAuthname | 1 | 1 | The name associated with the Annex that is used to fill the Name field in the PPP CHAP challenge message. If this value is a zero… |
1.3.6.1.4.1.15.2.5.72 | anxTimeServerAddr | 1 | 1 | The Internet address of the time server host. This MIB object corresponds to the NA/admin Annex parameter 'time_server'. |
1.3.6.1.4.1.15.2.5.78 | anxMopPrefHost | 1 | 1 | The Ethernet address of the preferred MOP load/dump host. The default value is 0-0-0-0-0-0. Each part of the address must be a h… |
1.3.6.1.4.1.15.2.5.79 | anxMopPassword | 1 | 1 | The 8 byte hexadecimal MOP maintenance password. Each byte is represented by two hex digits in the string. This MIB object corre… |
1.3.6.1.4.1.15.2.5.80 | anxMopLoginPassword | 1 | 1 | The password for all ports where anxpCliInterface parameter is set to vci and anxpVciLoginPortPassword is enabled. The default v… |
1.3.6.1.4.1.15.2.5.81 | anxMopLoginPrompt | 1 | 1 | The password prompt for all ports whose anxpCliInterface parameter is set to vci. The default is '#'. This MIB object corresponds… |
1.3.6.1.4.1.15.2.5.82 | anxMopLoginTimer | 1 | 1 | The inactivity timer for all ports whose anxpCliInterface parameter is set to vci. Setting this object to 0 results in a default v… |
1.3.6.1.4.1.15.2.5.83 | anxIpxFrameType | 1 | 1 | The framing used for IPX protocol packets. The default value is raw802. This MIB object corresponds to the NA/admin Annex parame… |
1.3.6.1.4.1.15.2.5.89 | anxTmuxEnable | 1 | 1 | Controls whether the Annex uses TMux to multiplex small TCP or UDP packets into a single IP packet. The host must also support TM… |
... |