This Annex parameter specifies which remote
group codes are accessible to virtual cli users.
All virtual cli users have the same group code.
The syntax is a series of numbers between 0 and 255,
separated by commas and dashes, such as 1,5,100-255.
The keywords 'all' and 'none' are also accepted
and will enable all or disable all groups,
respectively.
This MIB object corresponds to the NA/admin
Annex parameter 'vcli_groups'.
Note: You may use either this object or
anxLatAuthMap object to read or set the
'group_value' parameter.anxLatAuthMap is
preferred.
Parsed from file xylo-anx.mib.txt
Company: None
Module: XYLO-ANNEX-MIB
This Annex parameter specifies which remote
group codes are accessible to virtual cli users.
All virtual cli users have the same group code.
The value is displayed as a string of hex
characters with each bit defining whether a
specific group is enabled or disabled.
Parsed from file ANNEX-MIB.mib
Module: ANNEX-MIB
Vendor: Xylogics, Inc.
Module: ANNEX-MIB
[Automatically extracted from oidview.com]
anxLatVcliGroupVal OBJECT-TYPE SYNTAX DisplayString (SIZE (0..610)) ACCESS read-write STATUS deprecated DESCRIPTION "This Annex parameter specifies which remote group codes are accessible to virtual cli users. All virtual cli users have the same group code. The syntax is a series of numbers between 0 and 255, separated by commas and dashes, such as 1,5,100-255. The keywords 'all' and 'none' are also accepted and will enable all or disable all groups, respectively. This MIB object corresponds to the NA/admin Annex parameter 'vcli_groups'. Note: You may use either this object or anxLatAuthMap object to read or set the 'group_value' parameter.anxLatAuthMap is preferred." ::= { annexconfig 50 }
anxLatVcliGroupVal OBJECT-TYPE SYNTAX DisplayString (SIZE (32)) ACCESS read-write STATUS mandatory DESCRIPTION "This Annex parameter specifies which remote group codes are accessible to virtual cli users. All virtual cli users have the same group code. The value is displayed as a string of hex characters with each bit defining whether a specific group is enabled or disabled." ::= { annexconfig 50 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.15.2.5.50.0 | anxLatVcliGroupVal | 0 | 0 | None |
To many brothers! Only 100 nearest brothers are shown.
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
... | ||||
1.3.6.1.4.1.15.2.5.1 | anxInetAddr | 1 | 1 | The Internet address of the Annex. |
1.3.6.1.4.1.15.2.5.2 | anxPrefLoadAddr | 1 | 1 | The preferred load address for the Annex. |
1.3.6.1.4.1.15.2.5.3 | anxPrefDumpAddr | 1 | 1 | The preferred dump address for the Annex. |
1.3.6.1.4.1.15.2.5.4 | anxLoadDumpGateway | 1 | 1 | The Internet address of a gateway used when the preferred load or dump host is on a different network or subnet. |
1.3.6.1.4.1.15.2.5.5 | anxLoadDumpSeq | 1 | 1 | Lists the available network interfaces and the order that the Annex uses them when doing a down-line load or up-line dump. |
1.3.6.1.4.1.15.2.5.6 | anxLoadBcast | 1 | 1 | This parameter defines whether the Annex broadcasts for the config or the motd files if they were not found on the preferred load … |
1.3.6.1.4.1.15.2.5.7 | anxServerCap | 1 | 1 | Defines whether the Annex can act as a file server host for another Annex. The allowable values are 'all', 'none' (the default), … |
1.3.6.1.4.1.15.2.5.8 | anxTimeBcast | 1 | 1 | This parameter defines whether the Annex broadcasts for the time if the preferred load host does not provide a time server. |
1.3.6.1.4.1.15.2.5.9 | anxBcastAddr | 1 | 1 | The Internet address used by the Annex when sending broadcasts. |
1.3.6.1.4.1.15.2.5.10 | anxSubnetMask | 1 | 1 | The Internet subnet mask. |
1.3.6.1.4.1.15.2.5.11 | anxAuthAgent | 1 | 1 | This parameter controls whether the Annex can send an ICMP Address Mask Reply to a received ICMP Address Mask Request. |
1.3.6.1.4.1.15.2.5.12 | anxMaxVcli | 1 | 1 | The maximum number of virtual CLI connections allowed by the Annex at any one time. 0 means the Annex does not allow VCLI connec… |
1.3.6.1.4.1.15.2.5.13 | anxIpEncapType | 1 | 1 | This parameter specifies whether the Annex encapsulates IP packets in the Ethernet format or the IEEE 802.2/802.3 Data Link Layer… |
1.3.6.1.4.1.15.2.5.14 | anxNameServer1Type | 1 | 1 | The name service type used by the primary nameserver host. |
1.3.6.1.4.1.15.2.5.15 | anxNameServer1Addr | 1 | 1 | The Internet address of the primary nameserver host. |
1.3.6.1.4.1.15.2.5.16 | anxNameServer2Type | 1 | 1 | The name service type used by the secondary nameserver host. |
1.3.6.1.4.1.15.2.5.17 | anxNameServer2Addr | 1 | 1 | The Internet address of the secondary nameserver host. |
1.3.6.1.4.1.15.2.5.18 | anxNameServerBcast | 1 | 1 | This parameter controls whether the Annex broadcasts a name server request if the preferred name servers do not respond. |
1.3.6.1.4.1.15.2.5.19 | anxRwhod | 1 | 1 | Defines whether the Annex listens for RWHO broadcasts when building its host table. |
1.3.6.1.4.1.15.2.5.20 | anxMinUniqueHostNames | 1 | 1 | Defines whether the Annex minimum uniqueness feature is available. |
1.3.6.1.4.1.15.2.5.21 | anxHostTableSize | 1 | 1 | Defines the number of entries in the Annex host table. 0 indicates no host table. 251 sets no limit on the size of the table. |
1.3.6.1.4.1.15.2.5.22 | anxRouted | 1 | 1 | Defines whether the RIP-listener of the routing daemon on the Annex is enabled. |
1.3.6.1.4.1.15.2.5.23 | anxEnableSecurity | 1 | 1 | This parameter controls whether the Annex security system is enabled. |
1.3.6.1.4.1.15.2.5.24 | anxPassword | 1 | 1 | Setting this parameter changes the Annex's administration password. Reading this parameter will return either |
1.3.6.1.4.1.15.2.5.25 | anxSecurServer1Addr | 1 | 1 | The Internet address of the primary host where the Annex sends its security requests. |
1.3.6.1.4.1.15.2.5.26 | anxSecurServer2Addr | 1 | 1 | The Internet address of the secondary host where the Annex sends its security requests. |
1.3.6.1.4.1.15.2.5.27 | anxNetTurnAround | 1 | 1 | The amount of time (in seconds) that the Annex waits for a response from a security server. |
1.3.6.1.4.1.15.2.5.28 | anxSecurBcast | 1 | 1 | This parameter controls whether the Annex will broadcast its security requests when neither of the preferred security servers are… |
1.3.6.1.4.1.15.2.5.29 | anxVcliSecurity | 1 | 1 | This parameter controls whether the Annex performs user validation on the virtual CLI connections. |
1.3.6.1.4.1.15.2.5.30 | anxVcliPassword | 1 | 1 | This parameter defines a password used by the Annex when setting up a virtual CLI connection. |
1.3.6.1.4.1.15.2.5.31 | anxAcpKey | 1 | 1 | This parameter defines the Annex's encryption key used when exchanging messages between the Annex and the security server. |
1.3.6.1.4.1.15.2.5.32 | anxSysLogMask | 1 | 1 | Defines the priority levels of events logged in the Annex syslog file. The allowable values are 'all', 'none', or one or more of t… |
1.3.6.1.4.1.15.2.5.33 | anxSysLogFacility | 1 | 1 | This parameter defines the 4.3BSD syslog facility used in logging the Annex messages. |
1.3.6.1.4.1.15.2.5.34 | anxSysLogHost | 1 | 1 | The Internet address of the host configured to log Annex messages. |
1.3.6.1.4.1.15.2.5.35 | anxCliPrompt | 1 | 1 | The string used by the Annex to prompt all CLI users. |
1.3.6.1.4.1.15.2.5.36 | anxMotdFile | 1 | 1 | The host file name that contains the message-of-the-day for the Annex. |
1.3.6.1.4.1.15.2.5.37 | anxTftpDirName | 1 | 1 | Specifies the directory name to be prepended to all files (boot image, motd, macros, etc.) when booting via TFTP. |
1.3.6.1.4.1.15.2.5.38 | anxTftpDumpName | 1 | 1 | The full pathname of the TFTP dump file, if any. |
1.3.6.1.4.1.15.2.5.39 | anxTimeZone | 1 | 1 | Defines the timezone where the Annex resides in minutes west of GMT. |
1.3.6.1.4.1.15.2.5.40 | anxDaylightSavings | 1 | 1 | Defines the daylight savings time for the geographic location of the Annex. |
1.3.6.1.4.1.15.2.5.41 | anxLatKey | 1 | 1 | The Annex specific LAT key used to enable or disable the LAT protocol. |
1.3.6.1.4.1.15.2.5.42 | anxCircuitTimer | 1 | 1 | The time interval in tens of milliseconds between the transmission of LAT packets. |
1.3.6.1.4.1.15.2.5.43 | anxFacilityNum | 1 | 1 | The LAT facility number. |
1.3.6.1.4.1.15.2.5.44 | anxLatGroupVal | 1 | 1 | The Annex LAT group code for permitting access to LAT services. To access a specific LAT service, the Annex must have at least o… |
1.3.6.1.4.1.15.2.5.45 | anxKeepAliveTimer | 1 | 1 | The time interval, in seconds, between the transmission of identification packets during times of network inactivity. |
1.3.6.1.4.1.15.2.5.46 | anxReXmitLimit | 1 | 1 | The number of times to retransmit a packet before notifying the user of a network failure. |
1.3.6.1.4.1.15.2.5.47 | anxServerName | 1 | 1 | A string of up to 16 characters used to name the Annex in the LAT protocol. |
1.3.6.1.4.1.15.2.5.48 | anxServiceLimit | 1 | 1 | This parameter defines the upper bound on the number of services that the Annex can maintain in its local service table. |
1.3.6.1.4.1.15.2.5.49 | anxConfigFile | 1 | 1 | The name of the host file that contains the alias and menu entries. |
1.3.6.1.4.1.15.2.5.51 | anxLatQueueMax | 1 | 1 | Defines the maximum number of host requests (HIC's) that the Annex will save in its internal queue when the requested resource is… |
1.3.6.1.4.1.15.2.5.52 | anxLatLocation | 1 | 1 | A string of up to 32 characters used to identify the location of the Annex for the LAT protocol. |
1.3.6.1.4.1.15.2.5.53 | anxDisabledModules | 1 | 1 | Defines which selectable modules are currently disabled. The allowable values are 'all', 'none' or one or more of the following n… |
1.3.6.1.4.1.15.2.5.54 | anxSysLogPort | 1 | 1 | Specifies the Annex port number where syslog messages are sent. If set to 0, syslog messages are not sent to an Annex port. Thi… |
1.3.6.1.4.1.15.2.5.55 | anxOptionKey | 1 | 1 | The Annex specific software option key used to enable or disable the AppleTalk, dynamic routing and TN3270 support. This MIB obje… |
1.3.6.1.4.1.15.2.5.56 | anxIpFwdBcast | 1 | 1 | When enabled, all broadcasted IP packets are forwarded to all interfaces. This MIB object corresponds to the NA/admin Annex param… |
1.3.6.1.4.1.15.2.5.57 | anxLooseSrcRoute | 1 | 1 | When enabled, the Annex allows internet loose source routing. This MIB object corresponds to the NA/admin Annex parameter 'loose_… |
1.3.6.1.4.1.15.2.5.58 | anxAppleTalkRouter | 1 | 1 | The Ethernet address of the AppleTalk router. The default value is 0-0-0-0-0-0. Each part of the address must be a hex value sep… |
1.3.6.1.4.1.15.2.5.59 | anxAppleTalkDefZones | 1 | 1 | The comma separated list of AppleTalk zone names used as a default when ACP cannot supply the actual set of zone names. Commas, … |
1.3.6.1.4.1.15.2.5.60 | anxAppleTalkNodeId | 1 | 1 | The AppleTalk node ID that the Annex first tries to use at startup. The address consists of two parts separated by a dot. The a… |
1.3.6.1.4.1.15.2.5.61 | anxAppleTalkZone | 1 | 1 | The zone name that the Annex first tries to use at startup. Spaces and double quotes can be used in the zone name by preceding t… |
1.3.6.1.4.1.15.2.5.62 | anxRipRouteList | 1 | 1 | A list of one to eight IP addresses in dotted address format (ddd.ddd.ddd.ddd) with comma separators between the addresses. This… |
1.3.6.1.4.1.15.2.5.63 | anxRipAuth | 1 | 1 | This is a clear text password that is used to authenticate the RIP packets. If the NULL string is specified, RIP packet authenti… |
1.3.6.1.4.1.15.2.5.64 | anxTcpKeepAlive | 1 | 1 | The default keep-alive value in minutes for connections to this Annex. If this is zero, use the default value of 120 minutes. I… |
1.3.6.1.4.1.15.2.5.65 | anxMaxModemCalls | 1 | 1 | The number of calls for which modem call accounting information is kept. The default value is 20. |
1.3.6.1.4.1.15.2.5.66 | anxOutputTtl | 1 | 1 | The value that is placed in the ttl field of all locally generated IP packets. The default value is 64. This MIB object correspo… |
1.3.6.1.4.1.15.2.5.67 | anxSessionLimit | 1 | 1 | The maximum number of sessions allowed on the Annex. The default is 1152. The maximum value that can be set is actually 16 time… |
1.3.6.1.4.1.15.2.5.68 | anxLockEnable | 1 | 1 | When enabled, allows any port user to use the LOCK DECServer command. The default value is enabled. This MIB object corresponds … |
1.3.6.1.4.1.15.2.5.69 | anxPasswdLimit | 1 | 1 | Defines the maximum number of times a user on a port can attempt to enter a password before the Annex resets the port. Setting t… |
1.3.6.1.4.1.15.2.5.70 | anxLatMulticastTimer | 1 | 1 | The elapsed time in seconds between transmission of service announcements. The default value is 30 seconds. This MIB object corre… |
1.3.6.1.4.1.15.2.5.71 | anxChapAuthname | 1 | 1 | The name associated with the Annex that is used to fill the Name field in the PPP CHAP challenge message. If this value is a zero… |
1.3.6.1.4.1.15.2.5.72 | anxTimeServerAddr | 1 | 1 | The Internet address of the time server host. This MIB object corresponds to the NA/admin Annex parameter 'time_server'. |
1.3.6.1.4.1.15.2.5.78 | anxMopPrefHost | 1 | 1 | The Ethernet address of the preferred MOP load/dump host. The default value is 0-0-0-0-0-0. Each part of the address must be a h… |
1.3.6.1.4.1.15.2.5.79 | anxMopPassword | 1 | 1 | The 8 byte hexadecimal MOP maintenance password. Each byte is represented by two hex digits in the string. This MIB object corre… |
1.3.6.1.4.1.15.2.5.80 | anxMopLoginPassword | 1 | 1 | The password for all ports where anxpCliInterface parameter is set to vci and anxpVciLoginPortPassword is enabled. The default v… |
1.3.6.1.4.1.15.2.5.81 | anxMopLoginPrompt | 1 | 1 | The password prompt for all ports whose anxpCliInterface parameter is set to vci. The default is '#'. This MIB object corresponds… |
1.3.6.1.4.1.15.2.5.82 | anxMopLoginTimer | 1 | 1 | The inactivity timer for all ports whose anxpCliInterface parameter is set to vci. Setting this object to 0 results in a default v… |
1.3.6.1.4.1.15.2.5.83 | anxIpxFrameType | 1 | 1 | The framing used for IPX protocol packets. The default value is raw802. This MIB object corresponds to the NA/admin Annex parame… |
1.3.6.1.4.1.15.2.5.89 | anxTmuxEnable | 1 | 1 | Controls whether the Annex uses TMux to multiplex small TCP or UDP packets into a single IP packet. The host must also support TM… |
1.3.6.1.4.1.15.2.5.90 | anxTmuxMaxHost | 1 | 1 | The maximum size of the Tmux address table. If the number of host addresses exceeds this limit, the oldest entry is flushed. The… |
1.3.6.1.4.1.15.2.5.91 | anxTmuxMaxMpx | 1 | 1 | The largest packet that can be placed in a TMux packet. Larger packets are not multiplexed but are directly passed to the IP lay… |
1.3.6.1.4.1.15.2.5.92 | anxTmuxDelay | 1 | 1 | The maximum amount of time used to accumulate smaller packets into a larger packet. When the time expires, the multiplexed packe… |
1.3.6.1.4.1.15.2.5.93 | anxAllowSets | 1 | 1 | This object will return whether SNMP manager(client) has access to read or read-write the MIB objects. The access is determined b… |
1.3.6.1.4.1.15.2.5.94 | anxDefaultImageName | 1 | 1 | The name of the image file that is loaded by default when booting the Annex. This MIB object corresponds to the NA/admin Annex pa… |
1.3.6.1.4.1.15.2.5.95 | anxLatGroupMap | 1 | 1 | This parameter is functionally identical to anxLatGroupVal and corresponds to the NA/admin Annex parameter 'group_value'. The synt… |
1.3.6.1.4.1.15.2.5.96 | anxLatVcliGroupMap | 1 | 1 | This parameter is functionally identical to anxLatVcliGroupVal and corresponds to the NA/admin Annex parameter 'vcli_groups'. The … |
1.3.6.1.4.1.15.2.5.97 | anxMultiSession | 1 | 1 | This parameter allows multisession operation to be managed on a terminal server basis. It tells that the server is configured for… |
1.3.6.1.4.1.15.2.5.98 | anxVcliInactivity | 1 | 1 | This parameter will specify the amount of time in minutes that a vcli session can remain inactive. If the timer expires, the anne… |
1.3.6.1.4.1.15.2.5.99 | anxDHCPServer1Addr | 1 | 1 | The Internet address of the primary DHCP server host. This MIB object corresponds to the NA/admin Annex parameter `pref_DHCP1_addr… |
1.3.6.1.4.1.15.2.5.100 | anxDHCPServer2Addr | 1 | 1 | The Internet address of the secondary DHCP server host. This MIB object corresponds to the NA/admin Annex parameter `pref_DHCP2_ad… |
... |