Writing a value to this object causes the
annex to reset the appropriate subsystem. If
the value of this object is 'serialports',
'syncports', 'printerports', 'virtualports',
'vpnport' or
'interfaces', all objects
of the specified type are reset.
For T1 boards only, setting
t1_esf will reset all of the ESF counters in the
engine
t1-soft will reconfigure only the software
parameters which were changed.
t1-hard will reset the T1 engine affecting the
service.
pri_session(19) resets PRI session parameters
blocks. The RA6300 will re-read the Session
Parameter blocks from config.annex. Existing
calls will not be reset. No calls will be
answered while the PRImate is performing
the reset. The time to reset will depend
on the number of sessions which have to be
loaded from the host; it will typically
be less than one second.
The ippool object causes a reset of the pool
configuration which is equivalent to issuing a
reset command on the ippool command prompt.
Parsed from file xylo-anx.mib.txt
Company: None
Module: XYLO-ANNEX-MIB
Writing a value to this object causes the
annex to reset the appropriate subsystem.
Parsed from file ANNEX-MIB.mib
Module: ANNEX-MIB
Vendor: Xylogics, Inc.
Module: ANNEX-MIB
[Automatically extracted from oidview.com]
anxcReset OBJECT-TYPE SYNTAX INTEGER { all(1), macros(2), motd(3), nameserver(4), security(5), printerports(6), serialports(7), virtualports(8), syncports(9), dialout(11), lat(12), interfaces(13), annex-all(14), t1-esf(15), t1-soft(16), t1-hard(17), pri-session(19), vpnport(20), ippool(21), ntp(22), ippoolsystem(23) } ACCESS read-write STATUS mandatory DESCRIPTION "Writing a value to this object causes the annex to reset the appropriate subsystem. If the value of this object is 'serialports', 'syncports', 'printerports', 'virtualports', 'vpnport' or 'interfaces', all objects of the specified type are reset. For T1 boards only, setting t1_esf will reset all of the ESF counters in the engine t1-soft will reconfigure only the software parameters which were changed. t1-hard will reset the T1 engine affecting the service. pri_session(19) resets PRI session parameters blocks. The RA6300 will re-read the Session Parameter blocks from config.annex. Existing calls will not be reset. No calls will be answered while the PRImate is performing the reset. The time to reset will depend on the number of sessions which have to be loaded from the host; it will typically be less than one second. The ippool object causes a reset of the pool configuration which is equivalent to issuing a reset command on the ippool command prompt." ::= { annexcmds 5 }
anxcReset OBJECT-TYPE SYNTAX INTEGER { all(1), macros(2), motd(3), nameserver(4), security(5), printerport(6), serialports(7), virtualports(8) } ACCESS read-write STATUS mandatory DESCRIPTION "Writing a value to this object causes the annex to reset the appropriate subsystem." ::= { annexcmds 5 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.15.2.6.5.0 | anxcReset | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.15.2.6.1 | anxcBoot | 1 | 1 | The type of boot to be performed. To initiate a dump, this parameter needs to be set by the management station. The values stored… |
1.3.6.1.4.1.15.2.6.2 | anxcBootImage | 1 | 1 | The name of the image file to be used with the boot command. |
1.3.6.1.4.1.15.2.6.3 | anxcBootTime | 1 | 1 | The time at which the next boot is scheduled in HH:MM format. |
1.3.6.1.4.1.15.2.6.4 | anxcBootMsg | 1 | 1 | The broadcast message to be displayed when the next boot is performed. |
1.3.6.1.4.1.15.2.6.6 | anxcBcast | 1 | 1 | Writing a value to this object causes the annex to send the message in anxcBcastMsg to the specified port set. |
1.3.6.1.4.1.15.2.6.7 | anxcBcastMsg | 1 | 1 | The message to be broadcast to the Annex ports. |
1.3.6.1.4.1.15.2.6.8 | anxcResetSession | 1 | 1 | This command resets PRI session parameters blocks. The RA6300 will re-read the Session Parameter blocks from config.annex. Existi… |
1.3.6.1.4.1.15.2.6.9 | anxcResetDialout | 1 | 1 | Reset specific dialout routes using a range string. example: 1,3-5,8 will reset dialout routes 1,3,4,5,8. While 1,3-5,g,8 (g is b… |
1.3.6.1.4.1.15.2.6.10 | anxcResetWan1Chan | 1 | 1 | Resetting a particular channel on WAN 1. |
1.3.6.1.4.1.15.2.6.11 | anxcResetWan2Chan | 1 | 1 | Resetting a particular channel on WAN 2. |