Packet and octet count of matching traffic from all
ports where the entry is active. Set the mode to
'disable' when counters are not required.
Set the mode to 'bytes-pkts' when the count of octets
is accurately required. Set the mode to 'kbytes-pkts'
when the octets count is desired in kilobytes. Note
that there is a potential overflow of octet counter.
For example at a forwarding rate of 17 million 64-byte
pkts per second on an interface, if the statistics are
accumulated from 10 such interfaces in a 64-bit counter
the counter could overflow in approximately a year.
Parsed from file rapid_city-accelar.mib.txt
Company: rapidcity
Module: RAPID-CITY
rcFilterAceComnMatchCountMode OBJECT-TYPE SYNTAX INTEGER { disable(0), bytes-pkts(1), kbytes-pkts(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Packet and octet count of matching traffic from all ports where the entry is active. Set the mode to 'disable' when counters are not required. Set the mode to 'bytes-pkts' when the count of octets is accurately required. Set the mode to 'kbytes-pkts' when the octets count is desired in kilobytes. Note that there is a potential overflow of octet counter. For example at a forwarding rate of 17 million 64-byte pkts per second on an interface, if the statistics are accumulated from 10 such interfaces in a 64-bit counter the counter could overflow in approximately a year." DEFVAL { disable } ::= { rcFilterAceComnEntry 14 }
Vendor: Rapid City Communication
Module: RAPID-CITY
[Automatically extracted from oidview.com]
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2272.1.55.9.1.1.1 | rcFilterAceComnId | 0 | 0 | AceId uniquely identifies one Ace entry. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.2 | rcFilterAceComnPrecedence | 0 | 0 | Aces in a Acl are ordered based on precedence assigned by user.An acl can contain multiple ace's that match a packet. Precedence,… |
| 1.3.6.1.4.1.2272.1.55.9.1.1.3 | rcFilterAceComnName | 0 | 0 | A descriptive name choosen by the administrator. System automatically assigns a name if the user has not assigned one. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.4 | rcFilterAceComnTraffic | 0 | 0 | An ace's capability to match packets being 'routed' and 'bridged'. The support and accurate behavior for these options depends on… |
| 1.3.6.1.4.1.2272.1.55.9.1.1.5 | rcFilterAceComnMode | 0 | 0 | Operating Mode associated with the Ace is effective on the packets matching this Ace. 'Permit', 'deny', 'Redirect' are the operat… |
| 1.3.6.1.4.1.2272.1.55.9.1.1.6 | rcFilterAceComnAction | 0 | 0 | Additional actions performed by the Ace. Some options are not be compatbile with some modes of operation of the Ace. Any of the b… |
| 1.3.6.1.4.1.2272.1.55.9.1.1.7 | rcFilterAceComnRemarkDscp | 0 | 0 | The 6-bit DSCP field from the ToS byte in Ipv4 header encodes the PHB information per DiffServ standards (Refer to DiffServ RFCs … |
| 1.3.6.1.4.1.2272.1.55.9.1.1.8 | rcFilterAceComnRemarkDot1Priority | 0 | 0 | User Priority as described by Layer 2 standards: 802.1Q, 802.1p. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.9 | rcFilterAceComnRedirectNextHop | 0 | 0 | Redirect matching IP traffic to the next hop. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.10 | rcFilterAceComnRedirectUnreach | 0 | 0 | Set the desired behavior for redirected traffic in case the specified next-hop is not reachable. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.11 | rcFilterAceComnPolice | 0 | 0 | Policing profile Identifier. Set the desired policing profile identifier. Set the value 'disable' When policing is not desired. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.12 | rcFilterAceComnMatchCountPkts | 0 | 0 | Packet count of matching traffic on all ports where the rule is active. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.13 | rcFilterAceComnMatchCountOctets | 0 | 0 | Octet count of matching traffic on all ports where the rule is active. |
| 1.3.6.1.4.1.2272.1.55.9.1.1.15 | rcFilterAceComnRowStatus | 0 | 0 | Create/delete operations for this entry. |