Vendor: Interlan
Module: INXNMM-MIB
[Automatically extracted from oidview.com]
riHotFail OBJECT IDENTIFIER ::= { riLdcNmm 14 }
riHotFail OBJECT IDENTIFIER ::= { riLdcNmm 14 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.28.10.14.1 | riLdcHfAPrimaryAui | 1 | 1 | The number of the slot in which the primary Bus A backbone connectivity module for the chassis is installed.(CMM Slot is recommen… |
| 1.3.6.1.4.1.28.10.14.2 | riLdcHfAPrimaryMedia | 1 | 1 | The media type of the primary Bus A backbone connectivity module for the chassis. This variable returns backbone-thick(11) if th… |
| 1.3.6.1.4.1.28.10.14.3 | riLdcHfBPrimaryAui | 1 | 1 | The number of the slot in which the primary Bus B backbone connectivity module for the chassis is installed. You can set this va… |
| 1.3.6.1.4.1.28.10.14.4 | riLdcHfBPrimaryMedia | 1 | 1 | The media type of the primary Bus B backbone connectivity module for the chassis. This variable returns backbone-thick(11) if th… |
| 1.3.6.1.4.1.28.10.14.5 | riLdcHfABackupAui | 1 | 1 | The number of the slot in which the backup Bus A backbone connectivity module for the chassis is installed. Note: If you do not … |
| 1.3.6.1.4.1.28.10.14.6 | riLdcHfABackupMedia | 1 | 1 | The media type of the backup Bus A backbone connectivity module for the chassis. This variable returns backbone-thick(11) if the… |
| 1.3.6.1.4.1.28.10.14.7 | riLdcHfBBackupAui | 1 | 1 | The number of the slot in which the backup Bus B backbone connectivity module for the chassis is installed. You can set this var… |
| 1.3.6.1.4.1.28.10.14.8 | riLdcHfBBackupMedia | 1 | 1 | The media type of the backup Bus B backbone connectivity module for the chassis. This variable returns backbone-thick(11) if the… |
| 1.3.6.1.4.1.28.10.14.9 | riLdcHfIntState | 1 | 1 | The current state of internal hot failover detection for both Bus A and Bus B. Setting this variable to enabled(1) invokes inter… |
| 1.3.6.1.4.1.28.10.14.10 | riLdcHfIntPollFreq | 1 | 1 | The frequency, in seconds, with which the INX-NMM master and slave modules attempt to transmit a self-addressed packet onto the b… |
| 1.3.6.1.4.1.28.10.14.11 | riLdcHfIntRetries | 1 | 1 | The number of polling transmits (see the previous variable, Internal Polling Frequency) that must fail before internal failover i… |
| 1.3.6.1.4.1.28.10.14.12 | riLdcHfExtState | 1 | 1 | The current state of external hot failover detection. External hot failover detection is only available for the bus on which the … |
| 1.3.6.1.4.1.28.10.14.13 | riLdcHfExtPing1 | 1 | 1 | The IP adress of the node to which the master INX-NMM will ping to detect external cable failures. The master INX-NMM wil send t… |
| 1.3.6.1.4.1.28.10.14.14 | riLdcHfExtPing2 | 1 | 1 | The IP address of a second node to ping should the first host not respond (see the previous variable, Ext Failover Detection/Ping… |
| 1.3.6.1.4.1.28.10.14.15 | riLdcHfExtPollFreq | 1 | 1 | The frequency, in seconds, with which the master INX-NMM pings the address specified by Ext Failover Detection/Ping 1 or Ext Fail… |
| 1.3.6.1.4.1.28.10.14.16 | riLdcHfExtResponseTmo | 1 | 1 | The number of seconds the INX-NMM waits for a response to the ping before the ping is considered failed. The range of valid valu… |
| 1.3.6.1.4.1.28.10.14.17 | riLdcHfExtRetries | 1 | 1 | The number of pings to the host specified by Ext Failover Detection/Ping 1 that must fail before external failover is invoked. T… |
| 1.3.6.1.4.1.28.10.14.18 | riLdcHfHysteresis | 1 | 1 | The number of seconds required between failovers from the backup configuration to the primary configuration. This hysteresis time… |
| 1.3.6.1.4.1.28.10.14.19 | riLdcHfTable | 1 | 20 | riLdcHftable |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.28.10.1 | riLdcHardwareRev | 1 | 1 | The hardware revision level of the INX-CMM, which this variable returns as a hexadecimal display string. Note: This is NOT the ha… |
| 1.3.6.1.4.1.28.10.2 | riLdcFirmwareRev | 1 | 1 | The firmware revision level of the INX-CMM, i.e., the revision level of the INX-CMM PROMs. Note: This is NOT the firmware revisio… |
| 1.3.6.1.4.1.28.10.3 | riLdcChassisSoftwareRev | 1 | 1 | The software revision level of higher-level INX-CMM software. Currently, there is no higher-level software on the INX-CMM; all i… |
| 1.3.6.1.4.1.28.10.4 | riLdcChassisSerialNumber | 1 | 1 | The logic module serial number of the INX-CMM. |
| 1.3.6.1.4.1.28.10.5 | riLdcChassisStatus | 1 | 1 | The state of the modules in the chassis. This variable returns enabled(6) if any module in the chassis is set to enabled(6). It r… |
| 1.3.6.1.4.1.28.10.6 | riLdcChassisSlotCount | 1 | 1 | The total number of slots available in the chassis for INTERNExT modules. The INX5000-3 contains 3 slots, and the INX5000-12 con… |
| 1.3.6.1.4.1.28.10.7 | riLdcNumPowerSupplies | 1 | 1 | The number of power supplies that are installed in the INTERNExT chassis. This variable returns either 1 or 2, because the INX50… |
| 1.3.6.1.4.1.28.10.8 | riLdcNumBusMons | 1 | 1 | The number of entries in the Bus Monitor table, which contains statistics for the internal INTERNExT chassis buses. This variabl… |
| 1.3.6.1.4.1.28.10.9 | riLdcNumFans | 1 | 1 | The number of entries in the Fan Status table, which contains information about the chassis fans. This variable returns either 1… |
| 1.3.6.1.4.1.28.10.10 | riLdcChassisSlotTable | 1 | 23 | The Slot table contains information on the contents of each INTERNExT chassis slot. You cannot access this variable; it is only … |
| 1.3.6.1.4.1.28.10.11 | riLdcPowerSupplyTable | 1 | 3 | The Power Supply table contains information on the INTERNExT chassis power supplies. You cannot access this variable; it is only … |
| 1.3.6.1.4.1.28.10.12 | riLdcBusMonTable | 1 | 36 | The Bus Monitor table maintains traffic statistics on the internal buses of the INTERNExT chassis. You cannot access this variabl… |
| 1.3.6.1.4.1.28.10.13 | riLdcFanTable | 1 | 3 | The Fan Status table lists the status of all fans in the chassis. You cannot access this variable; it is only a table marker in t… |