The MIB module for Block Serial Tunneling.
Overview of BSTUN MIB
MIB description
The BSTUN MIB provides the configuration and operational information
on Cisco's blocked serial tunnelling implementation. The following
entities are managed:
1) Global BSTUN information
2) BSTUN groups
3) BSTUN ports
4) BSTUN routes
The following example configuration shows how the BSTUN MIB returns
BSTUN information, from either CISCO A or CISCO B.
HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC
line line device
1) The BSTUN global entry identifies the IP address by which the
router is known to other BSTUN peers, a configurable SAP value
on which to listen to LLC2 peers, and keepalive values to maintain
a session between TCP/IP peers.
2) The BSTUN group table identifies the BSTUN group number and protocol
type that Cisco A and Cisco B use to route BSC traffic over the
IP network. The table contains an entry for each BSTUN group
defined on the router. (The group number must be the same in Cisco A
and Cisco B, for traffic to flow from one router to the other.)
3) The BSTUN port table identifies the serial interface to the BSC
line for which the router is doing serial tunnelling. The MIB also
identifies the BSTUN group this interface is defined for, and
identifies the default routing for unrecognized BSC addresses.
There is a port entry for each BSTUN-enabled interface on the router.
4) The BSTUN route table has an entry for each address defined for
routing within the BSTUN group, and an entry for the default routing
if the 'bstun route all' command is configured. The route entry
includes identification of the BSTUN peer, priority, state, and
packet and byte counters.
Parsed from file CISCO-BSTUN-MIB.mib
Module: CISCO-BSTUN-MIB
ciscoBstunMIB MODULE-IDENTITY
LAST-UPDATED "200106190000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: [email protected]"
DESCRIPTION
"The MIB module for Block Serial Tunneling.
Overview of BSTUN MIB
MIB description
The BSTUN MIB provides the configuration and operational information
on Ciscos blocked serial tunnelling implementation. The following
entities are managed:
1) Global BSTUN information
2) BSTUN groups
3) BSTUN ports
4) BSTUN routes
The following example configuration shows how the BSTUN MIB returns
BSTUN information, from either CISCO A or CISCO B.
HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC
line line device
1) The BSTUN global entry identifies the IP address by which the
router is known to other BSTUN peers, a configurable SAP value
on which to listen to LLC2 peers, and keepalive values to maintain
a session between TCP/IP peers.
2) The BSTUN group table identifies the BSTUN group number and protocol
type that Cisco A and Cisco B use to route BSC traffic over the
IP network. The table contains an entry for each BSTUN group
defined on the router. (The group number must be the same in Cisco A
and Cisco B, for traffic to flow from one router to the other.)
3) The BSTUN port table identifies the serial interface to the BSC
line for which the router is doing serial tunnelling. The MIB also
identifies the BSTUN group this interface is defined for, and
identifies the default routing for unrecognized BSC addresses.
There is a port entry for each BSTUN-enabled interface on the router.
4) The BSTUN route table has an entry for each address defined for
routing within the BSTUN group, and an entry for the default routing
if the stun route all command is configured. The route entry
includes identification of the BSTUN peer, priority, state, and
packet and byte counters.
"
REVISION "200106190000Z"
DESCRIPTION
"Added Bisync to IP conversion peer support"
REVISION "9701220000Z"
DESCRIPTION
"Added frame-relay and other support"
REVISION "9508210000Z"
DESCRIPTION
"Minor cleanups to pacify mib compiler."
View at oid-info.com
The MIB module for Block Serial Tunneling.
Overview of BSTUN MIB
MIB description
The BSTUN MIB provides the configuration and operational information
on Cisco's blocked serial tunnelling implementation. The following
entities are managed:
1) Global BSTUN information
2) BSTUN groups
3) BSTUN ports
4) BSTUN routes
The following example configuration shows how the BSTUN MIB returns
BSTUN information, from either CISCO A or CISCO B.
HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC
line line device
1) The BSTUN global entry identifies the IP address by which the
router is known to other BSTUN peers, a configurable SAP value
on which to listen to LLC2 peers, and keepalive values to maintain
a session between TCP/IP peers.
2) The BSTUN group table identifies the BSTUN group number and protocol
type that Cisco A and Cisco B use to route BSC traffic over the
IP network. The table contains an entry for each BSTUN group
defined on the router. (The group number must be the same in Cisco A
and Cisco B, for traffic to flow from one router to the other.)
3) The BSTUN port table identifies the serial interface to the BSC
line for which the router is doing serial tunnelling. The MIB also
identifies the BSTUN group this interface is defined for, and
identifies the default routing for unrecognized BSC addresses.
There is a port entry for each BSTUN-enabled interface on the router.
4) The BSTUN route table has an entry for each address defined for
routing within the BSTUN group, and an entry for the default routing
if the 'bstun route all' command is configured. The route entry
includes identification of the BSTUN peer, priority, state, and
packet and byte counters.
Parsed from file CISCO-BSTUN-MIB.my.txt
Company: None
Module: CISCO-BSTUN-MIB
The MIB module for Block Serial Tunneling.
Overview of BSTUN MIB
MIB description
The BSTUN MIB provides the configuration and operational information
on Cisco's blocked serial tunnelling implementation. The following
entities are managed:
1) Global BSTUN information
2) BSTUN groups
3) BSTUN ports
4) BSTUN routes
The following example configuration shows how the BSTUN MIB returns
BSTUN information, from either CISCO A or CISCO B.
HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC
line line device
1) The BSTUN global entry identifies the IP address by which the
router is known to other BSTUN peers, a configurable SAP value
on which to listen to LLC2 peers, and keepalive values to maintain
a session between TCP/IP peers.
2) The BSTUN group table identifies the BSTUN group number and protocol
type that Cisco A and Cisco B use to route BSC traffic over the
IP network. The table contains an entry for each BSTUN group
defined on the router. (The group number must be the same in Cisco A
and Cisco B, for traffic to flow from one router to the other.)
3) The BSTUN port table identifies the serial interface to the BSC
line for which the router is doing serial tunnelling. The MIB also
identifies the BSTUN group this interface is defined for, and
identifies the default routing for unrecognized BSC addresses.
There is a port entry for each BSTUN-enabled interface on the router.
4) The BSTUN route table has an entry for each address defined for
routing within the BSTUN group, and an entry for the default routing
if the 'bstun route all' command is configured. The route entry
includes identification of the BSTUN peer, priority, state, and
packet and byte counters.
ciscoBstunMIB MODULE-IDENTITY LAST-UPDATED "200302100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB module for Block Serial Tunneling. Overview of BSTUN MIB MIB description The BSTUN MIB provides the configuration and operational information on Cisco's blocked serial tunnelling implementation. The following entities are managed: 1) Global BSTUN information 2) BSTUN groups 3) BSTUN ports 4) BSTUN routes The following example configuration shows how the BSTUN MIB returns BSTUN information, from either CISCO A or CISCO B. HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC line line device 1) The BSTUN global entry identifies the IP address by which the router is known to other BSTUN peers, a configurable SAP value on which to listen to LLC2 peers, and keepalive values to maintain a session between TCP/IP peers. 2) The BSTUN group table identifies the BSTUN group number and protocol type that Cisco A and Cisco B use to route BSC traffic over the IP network. The table contains an entry for each BSTUN group defined on the router. (The group number must be the same in Cisco A and Cisco B, for traffic to flow from one router to the other.) 3) The BSTUN port table identifies the serial interface to the BSC line for which the router is doing serial tunnelling. The MIB also identifies the BSTUN group this interface is defined for, and identifies the default routing for unrecognized BSC addresses. There is a port entry for each BSTUN-enabled interface on the router. 4) The BSTUN route table has an entry for each address defined for routing within the BSTUN group, and an entry for the default routing if the 'bstun route all' command is configured. The route entry includes identification of the BSTUN peer, priority, state, and packet and byte counters. " REVISION "200302100000Z" DESCRIPTION "Added Asynchronous POS to IP conversion support" REVISION "200106190000Z" DESCRIPTION "Added Bisync to IP conversion peer support" REVISION "9701220000Z" DESCRIPTION "Added frame-relay and other support" REVISION "9508210000Z" DESCRIPTION "Minor cleanups to pacify mib compiler." ::= { ciscoMgmt 35 }
ciscoBstunMIB OBJECT IDENTIFIER ::= { ciscoMgmt 35 }
Automatically extracted from Cisco "SNMP v2 MIBs".
ciscoBstunMIB MODULE-IDENTITY LAST-UPDATED "200302100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB module for Block Serial Tunneling. Overview of BSTUN MIB MIB description The BSTUN MIB provides the configuration and operational information on Cisco's blocked serial tunnelling implementation. The following entities are managed: 1) Global BSTUN information 2) BSTUN groups 3) BSTUN ports 4) BSTUN routes The following example configuration shows how the BSTUN MIB returns BSTUN information, from either CISCO A or CISCO B. HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC line line device 1) The BSTUN global entry identifies the IP address by which the router is known to other BSTUN peers, a configurable SAP value on which to listen to LLC2 peers, and keepalive values to maintain a session between TCP/IP peers. 2) The BSTUN group table identifies the BSTUN group number and protocol type that Cisco A and Cisco B use to route BSC traffic over the IP network. The table contains an entry for each BSTUN group defined on the router. (The group number must be the same in Cisco A and Cisco B, for traffic to flow from one router to the other.) 3) The BSTUN port table identifies the serial interface to the BSC line for which the router is doing serial tunnelling. The MIB also identifies the BSTUN group this interface is defined for, and identifies the default routing for unrecognized BSC addresses. There is a port entry for each BSTUN-enabled interface on the router. 4) The BSTUN route table has an entry for each address defined for routing within the BSTUN group, and an entry for the default routing if the 'bstun route all' command is configured. The route entry includes identification of the BSTUN peer, priority, state, and packet and byte counters. " REVISION "200302100000Z" DESCRIPTION "Added Asynchronous POS to IP conversion support" REVISION "200106190000Z" DESCRIPTION "Added Bisync to IP conversion peer support" REVISION "9701220000Z" DESCRIPTION "Added frame-relay and other support" REVISION "9508210000Z" DESCRIPTION "Minor cleanups to pacify mib compiler." ::= { ciscoMgmt 35 }
ciscoBstunMIB MODULE-IDENTITY LAST-UPDATED "200302100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB module for Block Serial Tunneling. Overview of BSTUN MIB MIB description The BSTUN MIB provides the configuration and operational information on Cisco's blocked serial tunnelling implementation. The following entities are managed: 1) Global BSTUN information 2) BSTUN groups 3) BSTUN ports 4) BSTUN routes The following example configuration shows how the BSTUN MIB returns BSTUN information, from either CISCO A or CISCO B. HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC line line device 1) The BSTUN global entry identifies the IP address by which the router is known to other BSTUN peers, a configurable SAP value on which to listen to LLC2 peers, and keepalive values to maintain a session between TCP/IP peers. 2) The BSTUN group table identifies the BSTUN group number and protocol type that Cisco A and Cisco B use to route BSC traffic over the IP network. The table contains an entry for each BSTUN group defined on the router. (The group number must be the same in Cisco A and Cisco B, for traffic to flow from one router to the other.) 3) The BSTUN port table identifies the serial interface to the BSC line for which the router is doing serial tunnelling. The MIB also identifies the BSTUN group this interface is defined for, and identifies the default routing for unrecognized BSC addresses. There is a port entry for each BSTUN-enabled interface on the router. 4) The BSTUN route table has an entry for each address defined for routing within the BSTUN group, and an entry for the default routing if the 'bstun route all' command is configured. The route entry includes identification of the BSTUN peer, priority, state, and packet and byte counters. " REVISION "200302100000Z" DESCRIPTION "Added Asynchronous POS to IP conversion support" REVISION "200106190000Z" DESCRIPTION "Added Bisync to IP conversion peer support" REVISION "9701220000Z" DESCRIPTION "Added frame-relay and other support" REVISION "9508210000Z" DESCRIPTION "Minor cleanups to pacify mib compiler." ::= { ciscoMgmt 35 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.35.1 | bstunObjects | 4 | 46 | None |
| 1.3.6.1.4.1.9.9.35.2 | bstunNotificationPrefix | 1 | 4 | None |
| 1.3.6.1.4.1.9.9.35.3 | bstunMibConformance | 2 | 18 | None |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.9.9.6 | ciscoTcpMIB | 3 | 20 | An extension to the IETF MIB module for managing TCP implementations |
| 1.3.6.1.4.1.9.9.10 | ciscoFlashMIB | 2 | 164 | This MIB provides for the management of Cisco Flash Devices. |
| 1.3.6.1.4.1.9.9.13 | ciscoEnvMonMIB | 4 | 68 | The MIB module to describe the status of the Environmental Monitor on those devices which support one. |
| 1.3.6.1.4.1.9.9.16 | ciscoPingMIB | 3 | 31 | Modified description of ciscoPingAddress object. |
| 1.3.6.1.4.1.9.9.17 | ciscoVinesMIB | 2 | 188 | " REVISION "9506070000Z |
| 1.3.6.1.4.1.9.9.18 | ciscoIsdnuIfMIB | 3 | 29 | ISDN BRI integrated U Interface MIB module. This MIB manages the ISDN BRI integrated U Interface in the router. |
| 1.3.6.1.4.1.9.9.19 | ciscoSnapshotMIB | 2 | 28 | Snapshot routing MIB |
| 1.3.6.1.4.1.9.9.20 | channel | 2 | 169 | This is the MIB module for objects used to manage the Cisco Mainframe Channel Connection (CMCC) cards. |
| 1.3.6.1.4.1.9.9.22 | ciscoRptrMIB | 3 | 32 | " REVISION "9512050000Z |
| 1.3.6.1.4.1.9.9.23 | ciscoCdpMIB | 2 | 78 | The MIB module for management of the Cisco Discovery Protocol in Cisco devices. |
| 1.3.6.1.4.1.9.9.24 | ciscoDspuMIB | 2 | 150 | Used to define and manage DSPU objects. |
| 1.3.6.1.4.1.9.9.25 | ciscoImageMIB | 2 | 10 | Router image MIB which identify the capabilities and characteristics of the image |
| 1.3.6.1.4.1.9.9.26 | ciscoIsdnMib | 3 | 34 | The MIB module to describe the status of the ISDN Interfaces on the routers. |
| 1.3.6.1.4.1.9.9.27 | ciscoCallHistoryMib | 2 | 40 | The MIB module to describe and store the call information of the routers for accounting purposes. |
| 1.3.6.1.4.1.9.9.28 | ciscoSnaSdllcMIB | 3 | 28 | ciscoSnaSdllcMIB MODULE-IDENTITY LAST-UPDATED "9812170000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Cus… |
| 1.3.6.1.4.1.9.9.29 | ciscoRsrbMIB | 3 | 45 | This is the MIB module for objects used to manage RSRB. Overview of remote source-route bridging (RSRB) management and MIB MIB … |
| 1.3.6.1.4.1.9.9.30 | ciscoStunMIB | 3 | 41 | The MIB module for serial Tunneling. Overview of STUN MIB MIB description The STUN MIB provides the configuration and operationa… |
| 1.3.6.1.4.1.9.9.31 | ciscoTcpOffloadMIB | 2 | 20 | This is the MIB module for objects used to manage the cisco tcp offload feature. The IBM mainframe (host) supports TCP/IP. As a … |
| 1.3.6.1.4.1.9.9.32 | ciscoCipTcpIpMIB | 2 | 88 | This is the MIB module for objects used to manage the cisco TCP/IP stack running on the Cisco Mainframe Channel Connection (CMCC)… |
| 1.3.6.1.4.1.9.9.33 | ciscoCipCsnaMIB | 3 | 66 | None |
| 1.3.6.1.4.1.9.9.34 | ciscoCipLanMIB | 2 | 24 | This is the Management Information Base (MIB) module for objects used to manage the cisco internal LAN support in Cisco Mainframe… |
| 1.3.6.1.4.1.9.9.36 | ciscoBscMIB | 2 | 46 | The MIB module for BSC. Overview of BSC MIB MIB description The BSC MIB provides the configuration and operational information on… |
| 1.3.6.1.4.1.9.9.37 | ciscoQueueMIB | 3 | 23 | This is the MIB module for objects used to manage interface queuing in Cisco devices. |
| 1.3.6.1.4.1.9.9.38 | ciscoLecsMIB | 2 | 77 | The MIB module for the management of LANE Configuration in Cisco devices. |
| 1.3.6.1.4.1.9.9.39 | ciscoLesMIB | 2 | 82 | The MIB module for the management of LANE Service in Cisco devices. |
| 1.3.6.1.4.1.9.9.40 | ciscoBusMIB | 2 | 37 | The MIB module for the management of LANE broadcast and unknown servers. |
| 1.3.6.1.4.1.9.9.41 | ciscoSyslogMIB | 3 | 49 | The MIB module to describe and store the system messages generated by the IOS and any other OS which supports syslogs. |
| 1.3.6.1.4.1.9.9.42 | ciscoRttMonMIB | 3 | 816 | This module defines a MIB for Round Trip Time (RTT) monitoring of a list of targets, using a variety of protocols. The table struc… |
| 1.3.6.1.4.1.9.9.43 | ciscoConfigManMIB | 3 | 75 | Configuration management MIB. The MIB represents a model of configuration data that exists in various locations: running in use b… |
| 1.3.6.1.4.1.9.9.44 | ciscoICsuDsuMIB | 4 | 70 | Integrated CSU/DSU MIB module. For T1 and Switched 56 kbps interfaces. |
| 1.3.6.1.4.1.9.9.45 | ciscoAtmIfPhysMIB | 2 | 39 | A minimal set of managed objects for tracking the status of DS3/E3/DS1/E1 and SONET interfaces. |
| 1.3.6.1.4.1.9.9.46 | ciscoVtpMIB | 3 | 261 | The MIB module for entities implementing the VTP protocol and Vlan management. |
| 1.3.6.1.4.1.9.9.47 | ciscoModemMgmtMIB | 3 | 112 | This MIB module provides modem call related data for tracking the progress and status of a call. |
| 1.3.6.1.4.1.9.9.48 | ciscoMemoryPoolMIB | 3 | 32 | MIB module for monitoring memory pools |
| 1.3.6.1.4.1.9.9.49 | ciscoFrameRelayMIB | 2 | 158 | Cisco Frame Relay MIB |
| 1.3.6.1.4.1.9.9.50 | ciscoAtmServiceRegistryMIB | 2 | 14 | A MIB module to allow an NMS to monitor and configure the information which an ATM switch makes available via the ILMI's Service … |
| 1.3.6.1.4.1.9.9.51 | ciscoAtmSwAddrMIB | 2 | 11 | ATM Switch address MIB |
| 1.3.6.1.4.1.9.9.52 | ciscoIpEncryptionMIB | 3 | 51 | Used to manage the encryption feature. |
| 1.3.6.1.4.1.9.9.53 | ciscoVmpsMIB | 3 | 55 | The MIB module for the management of the VLAN Membership Policy Server. |
| 1.3.6.1.4.1.9.9.54 | ciscoTn3270ServerMIB | 3 | 105 | The MIB module for TN3270 Server. MIB description The PU and LU MIB are defined in RFC 1666. This MIB provides additional informa… |
| 1.3.6.1.4.1.9.9.55 | ciscoAsppMIB | 2 | 29 | The ASPP MIB provides the configuration and operational information on asynchronous polled protocols such as the asynchronous sec… |
| 1.3.6.1.4.1.9.9.56 | ciscoVlanBridgingMIB | 2 | 13 | A set of managed objects for optimizing access to bridging related data from RFC 1493. This MIB is modeled after portions of RFC… |
| 1.3.6.1.4.1.9.9.57 | ciscoCompressionServiceAdapterMIB | 2 | 19 | Used to manage the compression service adapter. |
| 1.3.6.1.4.1.9.9.59 | ciscoStackMakerMIB | 2 | 15 | The MIB module for Cisco Systems' StackMaker. |
| 1.3.6.1.4.1.9.9.60 | ciscoAtmDualPhyMIB | 3 | 26 | Initial version of this MIB module. Phy definition Throughout this document phy is used as an abbreviation for Physical Interface.… |
| 1.3.6.1.4.1.9.9.61 | ciscoAccessEnvMonMIB | 3 | 13 | The MIB module to describe the additional status of the Environmental Monitor on those Cisco Access devices which support one. |
| 1.3.6.1.4.1.9.9.62 | ciscoVoiceAnalogIfMIB | 2 | 90 | Analog Voice Interface MIB module. This MIB manages the E&M, FXO, FXS Interfaces in the router. |
| 1.3.6.1.4.1.9.9.63 | ciscoVoiceDialControlMIB | 3 | 377 | This MIB module enhances the IETF Dial Control MIB (RFC2128) by providing management of voice telephony peers on both a circuit-s… |
| 1.3.6.1.4.1.9.9.64 | ciscoVoiceInterfaceMIB | 2 | 24 | Common Voice Interface MIB module. The MIB module manages the common voice related parameters for both voice analog and ISDN inte… |
| 1.3.6.1.4.1.9.9.65 | ciscoPnniMIB | 2 | 49 | The MIB module for managing Cisco specific extensions to the ATM Forum PNNI MIB. |
| 1.3.6.1.4.1.9.9.66 | ciscoAal5MIB | 2 | 25 | Cisco Enterprise AAL5 MIB file that provide AAL5 specific information that are either excluded by RFC 1695 or specific to Cisco p… |
| 1.3.6.1.4.1.9.9.67 | ciscoAtmAccessListMIB | 2 | 39 | A cisco ATM access list mib module. |
| 1.3.6.1.4.1.9.9.68 | ciscoVlanMembershipMIB | 3 | 90 | The MIB module for the management of the VLAN Membership within the frame work of Cisco VLAN Architecture, v 2.0 by Keith McClog… |
| 1.3.6.1.4.1.9.9.69 | ciscoLecDataVccMIB | 3 | 13 | This MIB module is a Cisco extension to the ATM Forum's LANE Client MIB. This extension identifies those VCCs which are being us… |
| 1.3.6.1.4.1.9.9.72 | ciscoCipCmpcMIB | 3 | 46 | This is the Management Information Base (MIB) module for objects used to manage the Cisco Multi-Path Channel (MPC) support on Cis… |
| 1.3.6.1.4.1.9.9.73 | ciscoCipTgMIB | 2 | 98 | This is the Management Information Base (MIB) module for objects used to manage Transmission Groups (TGs) in Cisco Mainframe Chan… |
| 1.3.6.1.4.1.9.9.74 | ciscoDlswExtMIB | 3 | 134 | The MIB module for management of Cisco specific Data Link Switching protocol enhancements. DLSw is described in RFC 1795 and RFC… |
| 1.3.6.1.4.1.9.9.76 | ciscoDlcSwitchMIB | 2 | 55 | This is the MIB module for objects used to manage FRAS sessions to the endstation. These objects are specific to downstream or end… |
| 1.3.6.1.4.1.9.9.77 | ciscoLecExtMIB | 3 | 12 | This MIB module is a Cisco extension to the ATM Forum's LANE Client MIB. |
| 1.3.6.1.4.1.9.9.78 | ciscoAtmSigDiagMIB | 2 | 58 | The MIB module to facilitate the diagnosis of failures of ATM Signalling requests. Through this MIB, an ATM device retains infor… |
| 1.3.6.1.4.1.9.9.80 | ciscoFtpClientMIB | 2 | 29 | The MIB module for invoking Internet File Transfer Protocol (FTP) operations for network management purposes. |
| 1.3.6.1.4.1.9.9.81 | ciscoBulkFileMIB | 3 | 63 | The MIB module for creating and deleting bulk files of SNMP data for file transfer. |
| 1.3.6.1.4.1.9.9.82 | ciscoStpExtensionsMIB | 3 | 300 | The MIB module for managing Cisco extensions to the 802.1D Spanning Tree Protocol (STP). |
| 1.3.6.1.4.1.9.9.83 | ciscoWredMIB | 2 | 26 | Cisco WRED MIB - Overview Cisco Weighted Random Early Detection/Drop is a method which avoids traffic congestion on an output int… |
| 1.3.6.1.4.1.9.9.84 | ciscoIpStatMIB | 2 | 34 | Cisco IP Statistics MIB - Overview This MIB incorporates objects to provide support for the Cisco IP statistics as implemented in… |
| 1.3.6.1.4.1.9.9.85 | ciscoCasIfMIB | 2 | 119 | Channel Associated Signal Interface MIB module. This MIB manages the generic CAS (Channel Associated Signal)or DS0 clear channel … |
| ... | ||||