| 1.3.6.1.3.2.6.1.1 |
dsx1LineIndex | 0 | 0 |
This object should be made equal to ifIndex. The next paragraph describes its previous usage. Making the object equal to ifIndex… |
| 1.3.6.1.3.2.6.1.2 |
dsx1IfIndex | 0 | 0 |
This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.3.2.6.1.3 |
dsx1TimeElapsed | 0 | 0 |
The number of seconds that have elapsed since the beginning of the near end current error- measurement period. If, for some reas… |
| 1.3.6.1.3.2.6.1.4 |
dsx1ValidIntervals | 0 | 0 |
The number of previous near end intervals for which data was collected. The value will be 96 unless the interface was brought on… |
| 1.3.6.1.3.2.6.1.5 |
dsx1LineType | 0 | 0 |
This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits… |
| 1.3.6.1.3.2.6.1.6 |
dsx1LineCoding | 0 | 0 |
This variable describes the variety of Zero Code
Suppression used on this interface, which in turn affects a number of its charac… |
| 1.3.6.1.3.2.6.1.7 |
dsx1SendCode | 0 | 0 |
This variable indicates what type of code is being sent across the DS1 interface by the device. Setting this variable causes the … |
| 1.3.6.1.3.2.6.1.8 |
dsx1CircuitIdentifier | 0 | 0 |
This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.3.2.6.1.9 |
dsx1LoopbackConfig | 0 | 0 |
This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should ret… |
| 1.3.6.1.3.2.6.1.10 |
dsx1LineStatus | 0 | 0 |
This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarm… |
| 1.3.6.1.3.2.6.1.11 |
dsx1SignalMode | 0 | 0 |
'none' indicates that no bits are reserved for signaling on this channel.
'robbedBit' indicates that DS1 Robbed Bit Sig- naling i… |
| 1.3.6.1.3.2.6.1.12 |
dsx1TransmitClockSource | 0 | 0 |
The source of Transmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock.
'localTimin… |
| 1.3.6.1.3.2.6.1.13 |
dsx1Fdl | 0 | 0 |
This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties. Set any bits that are appro… |
| 1.3.6.1.3.2.6.1.14 |
dsx1InvalidIntervals | 0 | 0 |
The number of intervals in the range from 0 to dsx1ValidIntervals for which no data is available. This object will typically be … |
| 1.3.6.1.3.2.6.1.16 |
dsx1LineStatusLastChange | 0 | 0 |
The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was ente… |
| 1.3.6.1.3.2.6.1.17 |
dsx1LineStatusChangeTrapEnable | 0 | 0 |
Indicates whether dsx1LineStatusChange traps should be generated for this interface. |
| 1.3.6.1.3.2.6.1.18 |
dsx1LoopbackStatus | 0 | 0 |
This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks establi… |
| 1.3.6.1.3.2.6.1.19 |
dsx1Ds1ChannelNumber | 0 | 0 |
This variable represents the channel number of
the DS1/E1 on its parent Ds2/E2 or DS3/E3. A value of 0 indicated this DS1/E1 doe… |
| 1.3.6.1.3.2.6.1.20 |
dsx1Channelization | 0 | 0 |
Indicates whether this ds1/e1 is channelized or unchannelized. The value of enabledDs0 indicates that this is a DS1 channelized … |
| 1.3.6.1.3.2.6.1.21 |
dsx1LineMode | 0 | 0 |
This setting puts the T1 framer into either long-haul (CSU) mode or short-haul (DSU) mode. |
| 1.3.6.1.3.2.6.1.23 |
dsx1LineImpedance | 0 | 0 |
Nominal line impedance. For T1 and J1 lines, the value is typically balanced100ohms(3). For E1 lines, the value is typically un… |
| 1.3.6.1.3.2.6.1.100 |
dsx1LineBuildOut | 0 | 0 |
This variable represents the line build out in dB. |
| 1.3.6.1.3.2.6.1.101 |
dsx1PerformanceReport | 0 | 0 |
If the value is ds1Mib, then statistics are kept for this interface. |