OID reference

recConfigMode

1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3

Description

<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID chang…

Full description and source information

Identification

Identifier and names

Parent
1.3.6.1.4.1.1206.4.1.1.7.9.7.1 (recConfigEntry)
Node code
3
Node name
recConfigMode
Category
SNMP management object
Numeric OID
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3
URN notation
urn:oid:1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3
ASN.1, OID-IRI and named path variants
ASN.1 notation

{1 3 6 1 4 1 1206 4 1 1 7 9 7 1 3}

  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) org(3) dod(6) internet(1) private(4) ldap-enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) org(3) dod(6) internet(1) private(4) vendor-objects(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) enterprises(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-organization(3) dod(6) internet(1) private(4) enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-organization(3) dod(6) internet(1) private(4) enterprises(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
  • {iso(1) iso-organization(3) dod(6) internet(1) private(4) vendor-objects(1) nema(1206) transportation(4) protocols(1) layers(1) application(7) recMech(9) recConfigTable(7) recConfigEntry(1) recConfigMode(3)}
OID-IRI notation
  • /1/3/6/1/4/1/1206/4/1/1/7/9/7/1/3
  • /ISO/Identified-Organization/6/1/4/1/1206/4/1/1/7/9/7/1/3
  • /ISO/3/6/1/4/1/1206/4/1/1/7/9/7/1/3
Named path variants
  • /iso/identified-organization/dod/internet/private/enterprise/1206/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprise/1206/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprise/nema/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprise/nema/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprises/1206/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprises/1206/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprises/nema/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/enterprises/nema/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/1206/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/1206/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/nema/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/nema/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/vendor-objects/1206/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/vendor-objects/1206/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/vendor-objects/nema/transportation/protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • /iso/identified-organization/dod/internet/private/vendor-objects/nema/transportation/Protocols/layers/application/recMech/recConfigTable/recConfigEntry/recConfigMode
  • Additional combinations skipped.

SNMP properties

Value type
INTEGER
Maximum access defined by MIB
read-write
Status in MIB
mandatory, deprecated
Default value
onChange

Definitions may combine these properties differently.

Compare 2 source variants

Variant 1 — NTCIP published standard MIB annexes (reviewed modules)

Value type
INTEGER
Maximum access defined by MIB
read-write
Status in MIB
mandatory
Default value
onChange

Variant 2 — NTCIP published standard MIB annexes (reviewed modules), ITE public NTCIP working repository MIBs

Value type
INTEGER
Maximum access defined by MIB
read-write
Status in MIB
deprecated
Default value
onChange

Enumerated values

Numbers refer to source variants above. Each value is shown only for variants that define it.

ValueNameSource variants
1other1, 2
2onChange1, 2
3greaterThanValue1, 2
4smallerThanValue1, 2
5hysteresisBound1, 2
6periodic1, 2
7andedWithValue1, 2

Using this OID with SNMP

At least one MIB declaration places this object in a table row. A value belongs to a row instance; its suffix depends on the row's INDEX or AUGMENTS definition.

In NTCIP1201-RecMech, the row index recConfigID is declared as Integer32. A non-negative index value is encoded as one numeric subidentifier. An instance has the form .1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3.<recConfigID>. Use an index value actually present on the device and permitted by its MIB. Other definitions can differ.

snmpwalk [connection options] DEVICE .1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3

Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.

Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.

Available source records contain 3 distinct definitions; some records may not include a definition.

Show 3 published definitions

recConfigMode · unconfirmed

recConfigMode OBJECT-TYPE
   SYNTAX INTEGER { other (1),
                         onChange (2),
                         greaterThanValue (3),
                         smallerThanValue (4),
                         hysteresisBound (5),
                         periodic (6),
                         andedWithValue (7) }
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
        "<Definition>This object specifies the mode of operation for
           this recording. The modes are defined as follows:
           Value               Description
           other               the recording mode of operation is not
                               described in this standard, refer to the
                               device manual.
           onChange            trigger a recording when the object value
                               referenced by recConfigCompareOID
                               changes. The values of


                                                                                       

                                                                                       
                                                                                      

                             recConfigCompareValue and
                             recConfigCompareValue2 are ignored in
                             this mode.
          greaterThanValue   trigger a recording when the object value
                             referenced by recConfigCompareOID
                             becomes greater than the value of
                             recConfigCompareValue for the time
                             (tenth seconds) defined by
                             recConfigCompareValue2 (zero means
                             immediate logging).
          smallerThanValue   trigger a recording when the object value
                             referenced by recConfigCompareOID
                             becomes less than the value of
                             recConfigCompareValue for the time
                             (tenth seconds) defined by
                             recConfigCompareValue2 (zero means
                             immediate logging).
          hysteresisBound    trigger a recording when the object value
                             referenced by recConfigCompareOID
                             becomes less than or greater than the
                             bound values. The lowerbound value is the
                             lower value of recConfigCompareValue and
                             recConfigCompareValue2; the upperbound
                             value is the higher value of the two values.

                             When the object value becomes greater than
                             the upper bound value, subsequent triggering of
                             upperbound conditions shall not occur until
                             the object value becomes less than the
                             lower bound value.

                           When the object value becomes less than
                           the lower bound value, subsequent triggering
                           of lowerbound conditions shall not occur
                           until the object value becomes greater
                           than the upper bound value.
         periodic          trigger a recording every x seconds, where
                           x is defined by the value stored in
                           recConfigCompareValue. The values stored
                           in recConfigCompareValue2 and
                           recConfigCompareOID are ignored in this
                           mode.
         andedWithValue    trigger a recording when the object value
                           referenced by recConfigCompareOID ANDED
                           with the value of recConfigCompareValue
                           is NOT equal to zero for the time (tenth
                           seconds) defined by recConfigCompareValue2
                           (zero means immediate logging). This allows
                           monitoring of a specific bit; the condition
                           becomes true anytime that any one of the
                           selected bits become true.
        <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.97.1.3
      "
   DEFVAL {onChange}
::= { recConfigEntry 3 }

recConfigMode · deprecated

recConfigMode OBJECT-TYPE
SYNTAX       INTEGER { other (1),
                         onChange (2),
                         greaterThanValue (3),
                         smallerThanValue (4),
                         hysteresisBound (5),
                         periodic (6),
                         andedWithValue (7) }
MAX-ACCESS read-write
STATUS       deprecated
DESCRIPTION
   "<Definition>This object specifies the mode of operation for this
   recording. The modes are defined as follows:


             Value                       Description
             other                       the recording mode of operation is not
                                         described in this standard, refer to the
                                         device manual.
             onChange                    trigger a recording when the object value
                                         referenced by recConfigCompareOID
                                         changes. The values of
                                         recConfigCompareValue and
                                         recConfigCompareValue2 are ignored in
                                         this mode.
             greaterThanValue            trigger a recording when the object value
                                         referenced by recConfigCompareOID
                                         becomes greater than the value of
                                         recConfigCompareValue for the time
                                         (tenth seconds) defined by



                                                                                                

                                                                                        
                                                                                       

                               recConfigCompareValue2 (zero means
                               immediate logging).
            smallerThanValue   trigger a recording when the object value
                               referenced by recConfigCompareOID
                               becomes less than the value of
                               recConfigCompareValue for the time
                               (tenth seconds) defined by
                               recConfigCompareValue2 (zero means
                               immediate logging).
            hysteresisBound    trigger a recording when the object value
                               referenced by recConfigCompareOID
                               becomes less than or greater than the
                               bound values. The lowerbound value is the
                               lower value of recConfigCompareValue and
                               recConfigCompareValue2; the upperbound
                               value is the higher value of the two values.


                               When the object value becomes greater than
                               the upper bound value, subsequent triggering of
                               upperbound conditions shall not occur until
                               the object value becomes less than the
                               lower bound value.


                               When the object value becomes less than
                               the lower bound value, subsequent triggering
                               of lowerbound conditions shall not occur
                               until the object value becomes greater
                               than the upper bound value.
            periodic           trigger a recording every x seconds, where
                               x is defined by the value stored in
                               recConfigCompareValue. The values stored
                               in recConfigCompareValue2 and
                               recConfigCompareOID are ignored in this
                               mode.
            andedWithValue     trigger a recording when the object value
                               referenced by recConfigCompareOID ANDED
                               with the value of recConfigCompareValue




                                                                                           

                 
        

                                         is NOT equal to zero for the time (tenth
                                         seconds) defined by recConfigCompareValue2
                                         (zero means immediate logging). This allows
                                         monitoring of a specific bit; the condition
                                         becomes true anytime that any one of the
                                         selected bits become true.


  <Supplanted by> ISO26048-1-CondTrigger.fdCondTriggerMode (ISO 26048-1)
  <Informative> The replacement object adds the following modes: equal,
  notEqual, creation, deletion. It also distinguishes between an integer-
  based and octet-string-based bitwise comparison, which is required due to
  the elimination of Opaque.
  <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3"
DEFVAL     { onChange }
::= { recConfigEntry 3 }

recConfigMode · deprecated

recConfigMode  OBJECT-TYPE
  SYNTAX      INTEGER { other (1),
                        onChange (2),
                        greaterThanValue (3),
                        smallerThanValue (4),
                        hysteresisBound (5),
                        periodic (6),
                        andedWithValue (7) }
  MAX-ACCESS  read-write
  STATUS      deprecated
  DESCRIPTION
      "<Definition>This object specifies the mode of operation for 
        this recording. The modes are defined as follows:
        Value             Description
        other             the recording mode of operation is not 
                          described in this standard, refer to the 
                          device manual.
        onChange          trigger a recording when the object value 
                          referenced by recConfigCompareOID 
                          changes. The values of 
                          recConfigCompareValue and 
                          recConfigCompareValue2 are ignored in 
                          this mode.
        greaterThanValue  trigger a recording when the object value 
                          referenced by recConfigCompareOID 
                          becomes greater than the value of 
                          recConfigCompareValue for the time 
                          (tenth seconds) defined by 
                          recConfigCompareValue2 (zero means 
                          immediate logging).
        smallerThanValue  trigger a recording when the object value 
                          referenced by recConfigCompareOID 
                          becomes less than the value of 
                          recConfigCompareValue for the time 
                          (tenth seconds) defined by 
                          recConfigCompareValue2 (zero means 
                          immediate logging).
        hysteresisBound   trigger a recording when the object value 
                          referenced by recConfigCompareOID 
                          becomes less than or greater than the 
                          bound values. The lowerbound value is the 
                          lower value of recConfigCompareValue and 
                          recConfigCompareValue2; the upperbound 
                          value is the higher value of the two values. 

                          When the object value becomes greater than 
                          the upper bound value, subsequent triggering of 
                          upperbound conditions shall not occur until 
                          the object value becomes less than the 
                          lower bound value. 

                          When the object value becomes less than 
                          the lower bound value, subsequent triggering 
                          of lowerbound conditions shall not occur 
                          until the object value becomes greater 
                          than the upper bound value.
        periodic          trigger a recording every x seconds, where 
                          x is defined by the value stored in 
                          recConfigCompareValue. The values stored 
                          in recConfigCompareValue2 and 
                          recConfigCompareOID are ignored in this 
                          mode.
        andedWithValue    trigger a recording when the object value 
                          referenced by recConfigCompareOID ANDED 
                          with the value of recConfigCompareValue 
                          is NOT equal to zero for the time (tenth 
                          seconds) defined by recConfigCompareValue2 
                          (zero means immediate logging). This allows 
                          monitoring of a specific bit; the condition 
                          becomes true anytime that any one of the 
                          selected bits become true.
    <Superseded by> COND-TRIGGER-MIB.fdCondTriggerMode (ISO 20684-3)
    <Informative> The replacement object adds the following modes:
      equal, notEqual, creation, deletion. It also distinguishes between
      an integer-based and octet-string-based bitwise comparison, which is
      required due to the elimination of Opaque.
    <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3"
   DEFVAL  { onChange }
::= { recConfigEntry 3 }

Meaning

Descriptions

3 unique

Identical descriptions are grouped. Different wording and device-specific notes are retained.

Description 1

<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.97.1.3

Sources for this description

NTCIP published standard MIB annexes (reviewed modules)

See 1 matching source record

Description 2

<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Supplanted by> ISO26048-1-CondTrigger.fdCondTriggerMode (ISO 26048-1) <Informative> The replacement object adds the following modes: equal, notEqual, creation, deletion. It also distinguishes between an integer- based and octet-string-based bitwise comparison, which is required due to the elimination of Opaque. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3

Sources for this description

NTCIP published standard MIB annexes (reviewed modules)

See 1 matching source record

Description 3

<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Superseded by> COND-TRIGGER-MIB.fdCondTriggerMode (ISO 20684-3) <Informative> The replacement object adds the following modes: equal, notEqual, creation, deletion. It also distinguishes between an integer-based and octet-string-based bitwise comparison, which is required due to the elimination of Opaque. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3

Sources for this description

ITE public NTCIP working repository MIBs

See 1 matching source record

Evidence

Source records

3 records

Matching descriptions are grouped; open a group to compare definitions and supporting files.

Records for description 1NTCIP published standard MIB annexes (reviewed modules)1 record · 1 source

Description 1

recConfigMode · unconfirmedNTCIP published standard MIB annexes (reviewed modules)1 source

Status in source: unconfirmed.

Names: recConfigMode

Technical details
{
  "smi_kind": "OBJECT-TYPE",
  "definition": [
    "recConfigMode",
    "OBJECT-TYPE",
    "SYNTAX",
    "INTEGER",
    "{",
    "other",
    "(",
    "1",
    ")",
    ",",
    "onChange",
    "(",
    "2",
    ")",
    ",",
    "greaterThanValue",
    "(",
    "3",
    ")",
    ",",
    "smallerThanValue",
    "(",
    "4",
    ")",
    ",",
    "hysteresisBound",
    "(",
    "5",
    ")",
    ",",
    "periodic",
    "(",
    "6",
    ")",
    ",",
    "andedWithValue",
    "(",
    "7",
    ")",
    "}",
    "ACCESS",
    "read-write",
    "STATUS",
    "mandatory",
    "DESCRIPTION",
    "\"<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.97.1.3 \"",
    "DEFVAL",
    "{",
    "onChange",
    "}",
    "::=",
    "{",
    "recConfigEntry",
    "3",
    "}"
  ],
  "syntax_tree": [
    [
      "SimpleSyntax",
      "INTEGER",
      [
        "enumSpec",
        [
          [
            "other",
            1
          ],
          [
            "onChange",
            2
          ],
          [
            "greaterThanValue",
            3
          ],
          [
            "smallerThanValue",
            4
          ],
          [
            "hysteresisBound",
            5
          ],
          [
            "periodic",
            6
          ],
          [
            "andedWithValue",
            7
          ]
        ]
      ]
    ],
    null,
    [
      "MaxAccessPart",
      "read-write"
    ],
    [
      "Status",
      "mandatory"
    ],
    [
      "DESCRIPTION",
      "<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.97.1.3"
    ],
    null,
    null,
    null,
    [
      "DEFVAL",
      "onChange"
    ]
  ]
}
Records for description 2NTCIP published standard MIB annexes (reviewed modules)1 record · 1 source

Description 2

recConfigMode · deprecatedNTCIP published standard MIB annexes (reviewed modules)1 source

Status in source: deprecated.

Names: recConfigMode

Technical details
{
  "smi_kind": "OBJECT-TYPE",
  "definition": [
    "recConfigMode",
    "OBJECT-TYPE",
    "SYNTAX",
    "INTEGER",
    "{",
    "other",
    "(",
    "1",
    ")",
    ",",
    "onChange",
    "(",
    "2",
    ")",
    ",",
    "greaterThanValue",
    "(",
    "3",
    ")",
    ",",
    "smallerThanValue",
    "(",
    "4",
    ")",
    ",",
    "hysteresisBound",
    "(",
    "5",
    ")",
    ",",
    "periodic",
    "(",
    "6",
    ")",
    ",",
    "andedWithValue",
    "(",
    "7",
    ")",
    "}",
    "MAX-ACCESS",
    "read-write",
    "STATUS",
    "deprecated",
    "DESCRIPTION",
    "\"<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Supplanted by> ISO26048-1-CondTrigger.fdCondTriggerMode (ISO 26048-1) <Informative> The replacement object adds the following modes: equal, notEqual, creation, deletion. It also distinguishes between an integer- based and octet-string-based bitwise comparison, which is required due to the elimination of Opaque. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3\"",
    "DEFVAL",
    "{",
    "onChange",
    "}",
    "::=",
    "{",
    "recConfigEntry",
    "3",
    "}"
  ],
  "syntax_tree": [
    [
      "SimpleSyntax",
      "INTEGER",
      [
        "enumSpec",
        [
          [
            "other",
            1
          ],
          [
            "onChange",
            2
          ],
          [
            "greaterThanValue",
            3
          ],
          [
            "smallerThanValue",
            4
          ],
          [
            "hysteresisBound",
            5
          ],
          [
            "periodic",
            6
          ],
          [
            "andedWithValue",
            7
          ]
        ]
      ]
    ],
    null,
    [
      "MaxAccessPart",
      "read-write"
    ],
    [
      "Status",
      "deprecated"
    ],
    [
      "DESCRIPTION",
      "<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Supplanted by> ISO26048-1-CondTrigger.fdCondTriggerMode (ISO 26048-1) <Informative> The replacement object adds the following modes: equal, notEqual, creation, deletion. It also distinguishes between an integer- based and octet-string-based bitwise comparison, which is required due to the elimination of Opaque. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3"
    ],
    null,
    null,
    null,
    [
      "DEFVAL",
      "onChange"
    ]
  ]
}
Records for description 3ITE public NTCIP working repository MIBs1 record · 2 sources

Description 3

recConfigMode · deprecatedITE public NTCIP working repository MIBs2 sources

Status in source: deprecated.

Names: recConfigMode

Technical details
{
  "smi_kind": "OBJECT-TYPE",
  "definition": [
    "recConfigMode",
    "OBJECT-TYPE",
    "SYNTAX",
    "INTEGER",
    "{",
    "other",
    "(",
    "1",
    ")",
    ",",
    "onChange",
    "(",
    "2",
    ")",
    ",",
    "greaterThanValue",
    "(",
    "3",
    ")",
    ",",
    "smallerThanValue",
    "(",
    "4",
    ")",
    ",",
    "hysteresisBound",
    "(",
    "5",
    ")",
    ",",
    "periodic",
    "(",
    "6",
    ")",
    ",",
    "andedWithValue",
    "(",
    "7",
    ")",
    "}",
    "MAX-ACCESS",
    "read-write",
    "STATUS",
    "deprecated",
    "DESCRIPTION",
    "\"<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Superseded by> COND-TRIGGER-MIB.fdCondTriggerMode (ISO 20684-3) <Informative> The replacement object adds the following modes: equal, notEqual, creation, deletion. It also distinguishes between an integer-based and octet-string-based bitwise comparison, which is required due to the elimination of Opaque. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3\"",
    "DEFVAL",
    "{",
    "onChange",
    "}",
    "::=",
    "{",
    "recConfigEntry",
    "3",
    "}"
  ],
  "syntax_tree": [
    [
      "SimpleSyntax",
      "INTEGER",
      [
        "enumSpec",
        [
          [
            "other",
            1
          ],
          [
            "onChange",
            2
          ],
          [
            "greaterThanValue",
            3
          ],
          [
            "smallerThanValue",
            4
          ],
          [
            "hysteresisBound",
            5
          ],
          [
            "periodic",
            6
          ],
          [
            "andedWithValue",
            7
          ]
        ]
      ]
    ],
    null,
    [
      "MaxAccessPart",
      "read-write"
    ],
    [
      "Status",
      "deprecated"
    ],
    [
      "DESCRIPTION",
      "<Definition>This object specifies the mode of operation for this recording. The modes are defined as follows: Value Description other the recording mode of operation is not described in this standard, refer to the device manual. onChange trigger a recording when the object value referenced by recConfigCompareOID changes. The values of recConfigCompareValue and recConfigCompareValue2 are ignored in this mode. greaterThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes greater than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). smallerThanValue trigger a recording when the object value referenced by recConfigCompareOID becomes less than the value of recConfigCompareValue for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). hysteresisBound trigger a recording when the object value referenced by recConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of recConfigCompareValue and recConfigCompareValue2; the upperbound value is the higher value of the two values. When the object value becomes greater than the upper bound value, subsequent triggering of upperbound conditions shall not occur until the object value becomes less than the lower bound value. When the object value becomes less than the lower bound value, subsequent triggering of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value. periodic trigger a recording every x seconds, where x is defined by the value stored in recConfigCompareValue. The values stored in recConfigCompareValue2 and recConfigCompareOID are ignored in this mode. andedWithValue trigger a recording when the object value referenced by recConfigCompareOID ANDED with the value of recConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by recConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true. <Superseded by> COND-TRIGGER-MIB.fdCondTriggerMode (ISO 20684-3) <Informative> The replacement object adds the following modes: equal, notEqual, creation, deletion. It also distinguishes between an integer-based and octet-string-based bitwise comparison, which is required due to the elimination of Opaque. <Object Identifier> 1.3.6.1.4.1.1206.4.1.1.7.9.7.1.3"
    ],
    null,
    null,
    null,
    [
      "DEFVAL",
      "onChange"
    ]
  ]
}

Registration

Registration authorities

First Registration Authority (inferred from ancestor 1.3.6.1.4.1.1206)

Schopp Bruce J.

Siblings (12)

OIDNameDirect childrenDescendantsDescription
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.1 recConfigID00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.2 recConfigClass00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.4 recConfigCompareValue00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.5 recConfigCompareValue200
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.6 recConfigCompareOID00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.7 recConfigRecordOID00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.8 recConfigTriggerPoint00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.9 recConfigSamplePeriod00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.10 recConfigSampleOID00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.11 recConfigNumEntries00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.12 recConfigAction00
1.3.6.1.4.1.1206.4.1.1.7.9.7.1.13 recConfigStatus00