Vendor: Lucent Technologies
Module: EXCEL-SWITCH-MIB
[Automatically extracted from oidview.com]
excelTraps OBJECT IDENTIFIER ::= { excel 0 }
excelTraps OBJECT IDENTIFIER ::= { excel 0 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.1751.1.67.0.1 | excelCardUpTrap | 0 | 0 | This trap is sent when a card is recognized by the matrix for the first time. |
1.3.6.1.4.1.1751.1.67.0.2 | excelCardDownTrap | 0 | 0 | This trap is sent when a card goes out of service, is removed or for some reason is no longer recognized by the matrix. |
1.3.6.1.4.1.1751.1.67.0.3 | excelCardActiveTrap | 0 | 0 | This trap is sent after a switchover has occured from the standby to active card. excelDeviceCardSlotIndex will indicate the slo… |
1.3.6.1.4.1.1751.1.67.0.4 | excelFaultLoggedTrap | 0 | 0 | This trap is sent when a fault has occurred on a card. The slot number of the card on which a fault occurred is bound to the trap. |
1.3.6.1.4.1.1751.1.67.0.5 | excelRingUpTrap | 0 | 0 | This trap is sent when an Exnet ring comes up. |
1.3.6.1.4.1.1751.1.67.0.6 | excelRingDownTrap | 0 | 0 | This trap is sent when an Exnet ring goes down. |
1.3.6.1.4.1.1751.1.67.0.7 | excelSystemBusyTrap | 0 | 0 | If the system is in a Busy Condition, then the matrix EX/CPU is flooded with messages. All incoming calls will be ignored until t… |
1.3.6.1.4.1.1751.1.67.0.8 | excelSystemBusyWarningTrap | 0 | 0 | System Busy Warning state. |
1.3.6.1.4.1.1751.1.67.0.9 | excelSystemBusyClearedTrap | 0 | 0 | The System Busy condition on the switch has cleared. |
1.3.6.1.4.1.1751.1.67.0.10 | excelClockModeChangeTrap | 0 | 0 | This trap occurs when the clock mode was automatically switched or reference clock sources have been lost. The switch will automa… |
1.3.6.1.4.1.1751.1.67.0.11 | excelDSPResourceBlockTrap | 0 | 0 | This trap is sent when a DSP resource Block has occurred. |
1.3.6.1.4.1.1751.1.67.0.12 | excelDSPFuncNotCfgTrap | 0 | 0 | DSP Resource Function type not configured. |
1.3.6.1.4.1.1751.1.67.0.13 | excelDSPMgmtInconsistentTrap | 0 | 0 | DSP resource management inconsistent. |
1.3.6.1.4.1.1751.1.67.0.14 | excelDldTimeoutTrap | 0 | 0 | Download record timeout. |
1.3.6.1.4.1.1751.1.67.0.15 | excelRANUnAvailableTrap | 0 | 0 | Recorded announcement requested is no longer available in the system. |
1.3.6.1.4.1.1751.1.67.0.16 | excelResourceUtilThreshTrap | 0 | 0 | excelResourceUtilThreshtrap |
1.3.6.1.4.1.1751.1.67.0.17 | excelCardNotSuppTrap | 0 | 0 | Card type not supported. |
1.3.6.1.4.1.1751.1.67.0.18 | excelCardDldCorruptTrap | 0 | 0 | Card Download is corrupt |
1.3.6.1.4.1.1751.1.67.0.19 | excelCardNotRecTrap | 0 | 0 | Card type not recognized |
1.3.6.1.4.1.1751.1.67.0.20 | excelCardCfgResetTrap | 0 | 0 | Card's Configuration has been reset to defaults. |
1.3.6.1.4.1.1751.1.67.0.21 | excelCardConnMapFailTrap | 0 | 0 | Connection Map Failure. |
1.3.6.1.4.1.1751.1.67.0.22 | excelCardNoSWTrap | 0 | 0 | Software does not have download for card. |
1.3.6.1.4.1.1751.1.67.0.23 | excelCardNoALawTrap | 0 | 0 | Card does not support A-law encoding format. |
1.3.6.1.4.1.1751.1.67.0.24 | excelCardRevNotSuppTrap | 0 | 0 | Card revision not supported by system software revision. |
1.3.6.1.4.1.1751.1.67.0.25 | excelEthernetErrTrap | 0 | 0 | The switch determines the integrity of the host link by monitoring host ACKs to Poll messages. If two consecutive Poll messages a… |
1.3.6.1.4.1.1751.1.67.0.26 | excelNoFanTrayTrap | 0 | 0 | No fan tray installed |
1.3.6.1.4.1.1751.1.67.0.27 | excelExnetACommFailTrap | 0 | 0 | Exnet Port A - Communication failure |
1.3.6.1.4.1.1751.1.67.0.28 | excelExnetBCommFailTrap | 0 | 0 | Exnet Port B - Communication failure |
1.3.6.1.4.1.1751.1.67.0.29 | excelExnetAFiberFailTrap | 0 | 0 | Exnet Port A - Fiber laser failure |
1.3.6.1.4.1.1751.1.67.0.30 | excelExnetBFiberFailTrap | 0 | 0 | Exnet Port B - Fiber laser failure |
1.3.6.1.4.1.1751.1.67.0.31 | excelEXSAPITrap | 0 | 0 | This EXS Node is not using the extended API. |
1.3.6.1.4.1.1751.1.67.0.32 | excelEXSConfTSTrap | 0 | 0 | excelEXSConftSTrap |
1.3.6.1.4.1.1751.1.67.0.33 | excelEXSSCbusMasterChangedTrap | 0 | 0 | The master of the SCbus that the Excel EXNET Connect card represented by excelExnetConnectIndex resides on has changed. |
1.3.6.1.4.1.1751.1.67.0.34 | excelEXSSCbusFailureTrap | 0 | 0 | The SCbus that the Excel EXNET Connect card represented by excelExnetConnectIndex resides has failed. |
1.3.6.1.4.1.1751.1.67.0.35 | excelSS7NetCongestionTrap | 0 | 0 | SS7 Signaling Network traffic has reached congested levels. |
1.3.6.1.4.1.1751.1.67.0.36 | excelSS7RemISUPUnavailTrap | 0 | 0 | SS7 Remote ISUP unavailable. |
1.3.6.1.4.1.1751.1.67.0.37 | excelClockSourceLostTrap | 0 | 0 | The Reference Clock Source has been lost. No host intervention is needed for this occurance. The switch will automatically switc… |
1.3.6.1.4.1.1751.1.67.0.38 | excelClockSourceLostClearedTrap | 0 | 0 | The Reference Clock Source has been reestablished automatically by the switch. |
1.3.6.1.4.1.1751.1.67.0.39 | excelNoSupportDSPFuncTrap | 0 | 0 | Hardware cannot support function type. |
1.3.6.1.4.1.1751.1.67.0.40 | excelPartialMessageReceivedTrap | 0 | 0 | Partial message received. |
1.3.6.1.4.1.1751.1.67.0.41 | excelUnackedMsgTrap | 0 | 0 | Unacknowledged Message. |
1.3.6.1.4.1.1751.1.67.0.42 | excelNodeIDAlreadyExistsTrap | 0 | 0 | Node ID Already Exists. |
1.3.6.1.4.1.1751.1.67.0.43 | excelInvalidMsgLenTrap | 0 | 0 | Invalid Message Length. |
1.3.6.1.4.1.1751.1.67.0.44 | excelLogSpanIDExistsTrap | 0 | 0 | Logical span ID already exists on another node. |
1.3.6.1.4.1.1751.1.67.0.45 | excelNodeUpTrap | 0 | 0 | This trap is sent when the Agent recognizes a new node in the system. |
1.3.6.1.4.1.1751.1.67.0.46 | excelNodeDownTrap | 0 | 0 | This trap is sent when the Agent has lost connectivity to the switch. |
1.3.6.1.4.1.1751.1.67.0.47 | excelSubagentConnect | 0 | 0 | This trap is sent when the subagent process successfully connects with the master agent. |
1.3.6.1.4.1.1751.1.67.0.48 | excelSwitchConnect | 0 | 0 | This trap is sent when the subagent process successfully connects to the switch interface process. |
1.3.6.1.4.1.1751.1.67.0.49 | excelSwitchLossConnectivity | 0 | 0 | This trap is sent when the subagent process detects a loss of connectivity with the switch interface process |
1.3.6.1.4.1.1751.1.67.0.50 | excelSpanCarrierGroupAlarm | 0 | 0 | This trap is generated when the switch detects a Carrier Group Alarm for more then some customer configured time. |
1.3.6.1.4.1.1751.1.67.0.51 | excelSpanExcessiveSlips | 0 | 0 | This trap will occur when the switch detects an abnormally high number of slips occurring |
1.3.6.1.4.1.1751.1.67.0.52 | excelSpanJ1Failure | 0 | 0 | Generic J1 failure |
1.3.6.1.4.1.1751.1.67.0.53 | excelLineCardBusy | 0 | 0 | This trap will occur when the line card exceeds it's final traffic threshold level |
1.3.6.1.4.1.1751.1.67.0.54 | excelLineCardApproachBusy | 0 | 0 | This trap will occur when the line card reaches it's initial traffic threshold level |
1.3.6.1.4.1.1751.1.67.0.55 | excelLowMemory | 0 | 0 | This trap will occur when memory usage on the line card exceeds the defined threshold level |
1.3.6.1.4.1.1751.1.67.0.56 | excelCardStatusChange | 0 | 0 | This trap will occur on any generic card status change |
1.3.6.1.4.1.1751.1.67.0.57 | excelLowMemoryCleared | 0 | 0 | This trap will occur when memory usage on the line card returns below the defined threshold level |
1.3.6.1.4.1.1751.1.67.0.58 | excelGenericEvent | 0 | 0 | This trap will occur when an undefined event is received |
1.3.6.1.4.1.1751.1.67.0.59 | excelSubrateSwitchOver | 0 | 0 | None |
1.3.6.1.4.1.1751.1.67.0.60 | excelSwitchOverInterrupt | 0 | 0 | The D-channel has gone from being In Service to Out Of Service |
1.3.6.1.4.1.1751.1.67.0.61 | excelSwitchOverSuccess | 0 | 0 | The controller switchover was successful. The new D channel is now the controller |
1.3.6.1.4.1.1751.1.67.0.62 | excelSwitchOverFailure | 0 | 0 | The controller switchover failed. The existing D channel is still controlling the D channel |
1.3.6.1.4.1.1751.1.67.0.63 | excelBackupDiagnostics | 0 | 0 | Information Alarm when the state of the D channel changes |
1.3.6.1.4.1.1751.1.67.0.64 | excelSCbusMasterChange | 0 | 0 | The local bus clock master has changed e.g. If the EXNET Connect is configured to be the local (SC/MVIP) clock master and another… |
1.3.6.1.4.1.1751.1.67.0.65 | excelSCBusFail | 0 | 0 | This event occurs wheneve a matrix has lost contact with a remote SS7 card that is controlling CIC's that are located on that node |
1.3.6.1.4.1.1751.1.67.0.66 | excelGeneralSoftwareError | 0 | 0 | Default error message for unexpected errors. |
1.3.6.1.4.1.1751.1.67.0.67 | excelRearSlotController | 0 | 0 | Communications resources are being currently controlled by the corresponding rear slot |
1.3.6.1.4.1.1751.1.67.0.68 | excelFrontSlotController | 0 | 0 | Communications resources are being currently controlled by the corresponding front slot |
1.3.6.1.4.1.1751.1.67.0.69 | excelConnectNotification | 0 | 0 | None |
1.3.6.1.4.1.1751.1.67.0.70 | excelRouteTableUpdated | 0 | 0 | The active route table has been updated |
1.3.6.1.4.1.1751.1.67.0.71 | excelResourceGroupTableUpdated | 0 | 0 | The active resource group table has been updated |
1.3.6.1.4.1.1751.1.67.0.73 | excelOldRouteTableDeleted | 0 | 0 | A previously active routing table has been deleted |
1.3.6.1.4.1.1751.1.67.0.74 | excelRouteTableForcefullyDeleted | 0 | 0 | The active route tabel was forcefully deleted |
1.3.6.1.4.1.1751.1.67.0.75 | excelResourceGroupTableForceDelete | 0 | 0 | The active resource group table has been forcefully deleted |
1.3.6.1.4.1.1751.1.67.0.76 | excelLoadProblem | 0 | 0 | This event will occur when a problem occurs during the flash or RAM loading |
1.3.6.1.4.1.1751.1.67.0.77 | excelTFTPFailure | 0 | 0 | This event will occur when a problem occurs during TFTP processing |
1.3.6.1.4.1.1751.1.67.0.78 | excelPPLEventL3PCIC | 0 | 0 | PPL event received from Layer 3 Plus CIC, component ID 15. The possible event ID's are : 1 Reset confirm indication 8 Remote main… |
1.3.6.1.4.1.1751.1.67.0.79 | excelPPLEventL3PLINK | 0 | 0 | PPL event received from Layer 3 Plus Link, component ID 16. The possible eventID's are: 1 Remote Inhibit Confirmation 2 Remore Un… |
1.3.6.1.4.1.1751.1.67.0.80 | excelPPLEventCPC | 0 | 0 | PPL event received from Call Processing Control, component ID 18. The possible eventID's are: 3 Continuity check incoming failur… |
1.3.6.1.4.1.1751.1.67.0.81 | excelPPLEventSPRC | 0 | 0 | PPL event Signal Procedure Control (SPRC), component ID 19. The possible eventID's are: 1 Format error in incoming message 2 … |
1.3.6.1.4.1.1751.1.67.0.82 | excelPPLEventBLS | 0 | 0 | PPL event Blocking Signal Sending(BLS), component ID 22. The possible eventID's are: 1 Format error in incoming message 2 … |
1.3.6.1.4.1.1751.1.67.0.83 | excelPPLEventBLR | 0 | 0 | PPL event received from Blocking Signal Reception(BLR), component ID 23. The possible eventID's are: 1 Blocking/Unblocking… |
1.3.6.1.4.1.1751.1.67.0.84 | excelPPLEventCRS | 0 | 0 | PPL event Circuit Reset Sending (CRS), component ID 24. The possible eventID's are: 1 First expiration of timer 17 |
1.3.6.1.4.1.1751.1.67.0.85 | excelPPLEventCRR | 0 | 0 | PPL event Circuit Reset Reception (CRR), component ID 25. The possible eventID's are: 1 Circuit Reset Reception |
1.3.6.1.4.1.1751.1.67.0.86 | excelPPLEventUCIC | 0 | 0 | PPL event Unequipped CIC Reception (UCIC), component Id 26. The possible eventID's are: 1 Unequipted CIC Reception |
1.3.6.1.4.1.1751.1.67.0.87 | excelPPLEventCGRS | 0 | 0 | PPL event Circuit Group Reset Sending (CGRS), component Id 27. The possible eventID's are: 1 Failure to rcv ack after sending gro… |
1.3.6.1.4.1.1751.1.67.0.88 | excelPPLEventCGRR | 0 | 0 | PPL event Circuit Group Reset Reception (CGRR), component Id 28. The possible eventID's are: 1 Failure to rcv ack after sending … |
1.3.6.1.4.1.1751.1.67.0.89 | excelPPLEventGBUS | 0 | 0 | PPL event Circuit Group Un/blocking Sending (GBUS), component Id 29. The possible eventID's are: 1 Expiration of T19 - No CGBA a… |
1.3.6.1.4.1.1751.1.67.0.90 | excelPPLEventGBUR | 0 | 0 | PPL event Circuit Group Un/blocking Reception (GBUR), component Id 30. The possible eventID's are: 1 Circuit Group Un/blocking R… |
1.3.6.1.4.1.1751.1.67.0.91 | excelPPLEventHGBR | 0 | 0 | PPL event Hardware Oriented Circuit Group Un/blocking Reception (HGBR), component Id 32. The possible eventID's are: 1 Circuit Gr… |
1.3.6.1.4.1.1751.1.67.0.92 | excelPPLEventMTP3Hmdt | 0 | 0 | PPL event Message Transfer Part3 Layer (HMDT), component Id 43. The possible eventID's are: 0 Remote processor outage 1 Remote pr… |
1.3.6.1.4.1.1751.1.67.0.93 | excelPPLEventMTP3Lsac | 0 | 0 | PPL event Message Transfer Part3 Layer (LSAC), component Id 46. The possible eventID's are: 1 Link activation failure 2 Signaling… |
1.3.6.1.4.1.1751.1.67.0.94 | excelPPLEventMTP3Tlac | 0 | 0 | PPL event Message Transfer Part3 Layer (TLAC), component Id 60. The possible eventID's are: 0 Remote processor outage 1 Remote pr… |
1.3.6.1.4.1.1751.1.67.0.95 | excelPPLEventMTP3Tsfc | 0 | 0 | PPL event Message Transfer Part3 Layer (TSFC), component Id 63. The possible eventID's are: 1 Destination inaccessable 2 Destinat… |
1.3.6.1.4.1.1751.1.67.0.96 | excelPPLEventISUPHlb | 0 | 0 | PPL event ISUP HLB (ISUP Hardware Failure Oriented Locally Blocking State), component Id 36. The possible eventID's can be recei… |
1.3.6.1.4.1.1751.1.67.0.97 | excelPPLEventCRCR | 0 | 0 | PPL event CRCR, component Id 68. The possible eventID's can be received are: 1 REL received with check indicator set to 3 2 T27 t… |
1.3.6.1.4.1.1751.1.67.0.98 | excelPPLEventMGBS | 0 | 0 | PPL event MGBS(Maintaince Circuit Group blocking/unblocking Sending), component Id 69. The possible eventID's can be received ar… |
1.3.6.1.4.1.1751.1.67.0.99 | excelPPLEventHGBS | 0 | 0 | PPL event HGBS(Hardware Failure Circuit Group blocking/unblocking Sending), component Id 71. The possible eventID's are: 1 First… |
1.3.6.1.4.1.1751.1.67.0.100 | excelPPLEventCQS | 0 | 0 | PPL event CQS, component Id 118. The possible eventID's are: 3 Timer T28 expired |
1.3.6.1.4.1.1751.1.67.0.101 | excelPPLEventCVS | 0 | 0 | PPL event CVS, component Id 120. The possible eventID's are: 6 CVR receive failed after reattempt |
1.3.6.1.4.1.1751.1.67.0.102 | excelPPLEventCRCS | 0 | 0 | PPL event CRCS, component Id 129. The possible eventID's are: 1 T36 expired on continuity recheck 2 COT failure indication, proc… |
1.3.6.1.4.1.1751.1.67.0.103 | excelPPLEventCRO | 0 | 0 | PPL event CRO, component Id 131. The possible eventID's are: 2 T5 expired in Wait for Release Complete State 3 1st continuity re… |
1.3.6.1.4.1.1751.1.67.0.104 | excelDchannelFailure | 0 | 0 | ISDN D Channel is establishing. The distant end is not communicating on the D-channel. |
1.3.6.1.4.1.1751.1.67.0.105 | excelVoIPModuleOOS | 0 | 0 | The VDAC Voice over IP module is Out of Service. |
1.3.6.1.4.1.1751.1.67.0.106 | excelVoipModuleDead | 0 | 0 | The VDAC Voice over IP module is no longer communicating. |
1.3.6.1.4.1.1751.1.67.0.107 | excelVoipModuleDspDead | 0 | 0 | The VDAC Voice over IP DSP module is no longer communicating. |
1.3.6.1.4.1.1751.1.67.0.108 | excelVoipModuleReset | 0 | 0 | The VDAC Voice over IP module has been reset. |
1.3.6.1.4.1.1751.1.67.0.109 | excelMatrixSwitchover | 0 | 0 | A matrix switchover has occurred. |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.1751.1.67.1 | excel1 | 2 | 396 | None |
1.3.6.1.4.1.1751.1.67.2 | excel2, excelProducts | 4 | 783 | None |
1.3.6.1.4.1.1751.1.67.3 | excel3 | 2 | 396 | None |
1.3.6.1.4.1.1751.1.67.4 | excel4 | 2 | 396 | None |