The index value which uniquely identifies the CSU to which
this entry is applicable. The value of this object matches
the value of the index for the corresponding NAC entity in
the entity table of the chassis MIB.
Parsed from file RDS1.MIB.txt
Company: cai
Module: RDS1-MIB
Vendor: 3Com
Module: RDS1-MIB (RDS1.MIB)
Type: TABULAR
Access: read-only
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
usrds1StatIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the CSU to which this entry is applicable. The value of this object matches the value of the index for the corresponding NAC entity in the entity table of the chassis MIB." ::= { usrds1StatEntry 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.27.2.1.2 | usrds1StatReceiverGain | 0 | 0 | This object identifies the amount of gain applied to boost the receive signal level to an appropriate operating level. |
| 1.3.6.1.4.1.429.1.27.2.1.3 | usrds1StatSwitchTypeActve | 0 | 0 | usrds1StatSwitchtypeActve |
| 1.3.6.1.4.1.429.1.27.2.1.4 | usrds1StatDchanState | 0 | 0 | This object reflects the operational status of the D channel on the T1-PRI ISDN NAC. |
| 1.3.6.1.4.1.429.1.27.2.1.5 | usrds1StatE1ContCrc | 0 | 0 | This object indicates when continuous CRC errors are being received on the E1 DS1 span line on the T1-PRI ISDN NAC. |
| 1.3.6.1.4.1.429.1.27.2.1.6 | usrds1StatE1PhysicalState | 0 | 0 | This object reflects the physical state of the E1 DS1 span line on the T1-PRI ISDN NAC. |
| 1.3.6.1.4.1.429.1.27.2.1.7 | usrds1StatLoopBackInit | 0 | 0 | This object tells if the loopback was initiated by the network or by command |
| 1.3.6.1.4.1.429.1.27.2.1.8 | usrds1StatDs0SrvcChngLst | 0 | 0 | This object contains the current list of DS0s that have changed their state from In Service to Out of Service or Vice versa. The… |
| 1.3.6.1.4.1.429.1.27.2.1.9 | usrds1SignalModeActive | 0 | 0 | This object is the same as in 1406 but shows what the module booted up with. This is needed until the changes to the 1406 object … |
| 1.3.6.1.4.1.429.1.27.2.1.10 | usrinCallmodemNotAvail | 0 | 0 | Incremented every time an incoming call can not be completed due to no idle modem available. |
| 1.3.6.1.4.1.429.1.27.2.1.11 | usrinCallInvlidBearerCapa | 0 | 0 | Incremented every time the NPRI receives invalid bearer capability. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.12 | usrinCallInvalidChannlID | 0 | 0 | Incremented every time the NPRI receives invalid channel ID. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.13 | usrinCallInvlidProgrsInd | 0 | 0 | Incremented every time the NPRI receives invalid progress indicator. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.14 | usrinCallInvlidCallngPrty | 0 | 0 | Incremented every time the NPRI receives invalid calling party number. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.15 | usrinCallInvlidCalledPrty | 0 | 0 | Incremented every time the NPRI receives invalid called party number. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.16 | usrinCallCallBack | 0 | 0 | Incremented every time the NPRI blocks the incoming call. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.17 | usrinCallLoopStrtNoRngOff | 0 | 0 | Loop start, Pegged every time the no ring off after ring on. - CHT1 PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.18 | usroutCallTelcoDisconnct | 0 | 0 | Incremented every time the TELCO disconnect a setting up call. - PRI only. |
| 1.3.6.1.4.1.429.1.27.2.1.19 | usroutCallEMWinkTimeOut | 0 | 0 | E&M Wink start, Pegged every time the TELCO fails to wink (5 sec) - CHT1 only. |
| 1.3.6.1.4.1.429.1.27.2.1.20 | usroutCallEMWinkTooShort | 0 | 0 | E&M Wink start, Pegged every time the wink too short (less than 260 ms) - CHT1 only. |
| 1.3.6.1.4.1.429.1.27.2.1.21 | usroutCallNoChannelAvail | 0 | 0 | Incremented every time the NCC receives outgoing call request from TPS but there is no channel available for the outgoing call. |
| 1.3.6.1.4.1.429.1.27.2.1.22 | usrdiscNoTelcoRespDialIn | 0 | 0 | In E&M dialin state machine, TELCO does not respond to NCT disconnect signal. Pegged every time when it happens. - CHT1 only. |
| 1.3.6.1.4.1.429.1.27.2.1.23 | usrdiscNoTelcoRespDialOut | 0 | 0 | In E&M dialout state machine, TELCO does not respond to NCT disconnect signal. Pegged every time when it happens. - CHT1 only. |
| 1.3.6.1.4.1.429.1.27.2.1.24 | usrdiscNoTelcoRespGround | 0 | 0 | In ground start dial in and dial out state machine, TELCO, does not respond to NCT disconnect signal. Pegged every time when it h… |
| 1.3.6.1.4.1.429.1.27.2.1.25 | usrds0BulkAccessABStat | 0 | 0 | This object contains the AB bit status. It contains a string of bytes which contain the ABCD signaling transmit and receive bits … |
| 1.3.6.1.4.1.429.1.27.2.1.26 | usrds0BlkAccessStatDs0Mdm | 0 | 0 | This object contains all of the ids0Stat table parameters for all the DS0's on the DS1. |
| 1.3.6.1.4.1.429.1.27.2.1.27 | usrds1StatNFASSpanState | 0 | 0 | This object displays the span's current state with regard to D-channel. |
| 1.3.6.1.4.1.429.1.27.2.1.28 | usrds1StatSs7ModeActive | 0 | 0 | This object indicates what the active SS7 mode is after the NAC boots up. The usrds1CfgSs7Mode configuration object determines th… |
| 1.3.6.1.4.1.429.1.27.2.1.29 | usrds1StatLpBkDS0Cause | 0 | 0 | This object indicates the cause of the DS0 entering or exiting at a loop back. SLAP indicates that the DS0 loop back change was r… |