The scaling factor used for the third amperage probe to convert microvolts measured from the
Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Amp Detect module installed.
Parsed from file netbotz2.mib.txt
Company: None
Module: NETBOTZ-MIB
The scaling factor used for the third amperage probe to convert microvolts measured from the
Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Amp Detect module installed.
Parsed from file NETBOTZ-MIB.mib
Module: NETBOTZ-MIB
Vendor: NetBotz
Module: NETBOTZ-PRD-BOT-MIB
[Automatically extracted from oidview.com]
netBotz-prd-bot-amps3-uV-per-mA OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The scaling factor used for the third amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Amp Detect module installed." REFERENCE "NetBotz uVolts To 10 mAmps 3" ::= { netBotz-prd-bot 51 }
netBotz-prd-bot-amps3-uV-per-mA OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The scaling factor used for the third amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Amp Detect module installed." REFERENCE "NetBotz uVolts To 10 mAmps 3" ::= { netBotz-prd-bot 51 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5528.30.10.51.0 | netBotz-prd-bot-amps3-uV-per-mA | 0 | 0 | None |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.5528.30.10.1 | netBotz-prd-bot-temp | 1 | 1 | The reading of the temperature probe, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.2 | netBotz-prd-bot-humidity | 1 | 1 | The reading of the humidity probe, in percent. |
| 1.3.6.1.4.1.5528.30.10.3 | netBotz-prd-bot-airflow | 1 | 1 | The reading of the airflow probe. Each unit represents approximately 40 feet/minute or 13 meters/minute of airflow velocity. |
| 1.3.6.1.4.1.5528.30.10.4 | netBotz-prd-bot-audio | 1 | 1 | The reading of the audio alarm probe on/off. |
| 1.3.6.1.4.1.5528.30.10.5 | netBotz-prd-bot-doorajar | 1 | 1 | The reading of the door switch probe open(1) or closed(0). |
| 1.3.6.1.4.1.5528.30.10.6 | netBotz-prd-bot-temp-min | 1 | 1 | The temperature probe minimum, from 35 to 120 degrees F, or 1 to 50 degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.7 | netBotz-prd-bot-temp-max | 1 | 1 | The temperature probe maximum, from 35 to 120 degrees F, or 1 to 50 degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.8 | netBotz-prd-bot-humidity-min | 1 | 1 | The humidity probe minimum, from 10 to 90 percent. |
| 1.3.6.1.4.1.5528.30.10.9 | netBotz-prd-bot-humidity-max | 1 | 1 | The humidity probe maximum, from 10 to 90 percent. |
| 1.3.6.1.4.1.5528.30.10.10 | netBotz-prd-bot-airflow-mins | 1 | 1 | Minutes without airflow before alarm set. |
| 1.3.6.1.4.1.5528.30.10.11 | netBotz-prd-bot-audio-secs | 1 | 1 | Seconds of alarm audio before alarm set. |
| 1.3.6.1.4.1.5528.30.10.12 | netBotz-prd-bot-temp-enabled | 1 | 1 | Temperature probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.13 | netBotz-prd-bot-hum-enabled | 1 | 1 | Humidity probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.14 | netBotz-prd-bot-air-enabled | 1 | 1 | Airflow probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.15 | netBotz-prd-bot-audio-enabled | 1 | 1 | Audio probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.16 | netBotz-prd-bot-switch-state | 1 | 1 | Switch state setting. The state controls which condition of the door switch indicates an alarm. If set to 0, alarm is set when th… |
| 1.3.6.1.4.1.5528.30.10.17 | netBotz-prd-bot-switch-enabled | 1 | 1 | Door switch enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.18 | netBotz-prd-bot-audio-level | 1 | 1 | Audio level setting. This is the relative audio level, from 0-11, above which an alarm will be sent. |
| 1.3.6.1.4.1.5528.30.10.19 | netBotz-prd-bot-doorpic-delay | 1 | 1 | Number of seconds between door alert and first picture. |
| 1.3.6.1.4.1.5528.30.10.20 | netBotz-prd-bot-trap-index | 1 | 1 | The crawler ID of the last trap. |
| 1.3.6.1.4.1.5528.30.10.21 | netBotz-prd-bot-trap-address | 1 | 1 | The IP address of the last trap. |
| 1.3.6.1.4.1.5528.30.10.22 | netBotz-prd-bot-trap-oid | 1 | 1 | The object id of the last trap. |
| 1.3.6.1.4.1.5528.30.10.23 | netBotz-prd-bot-trap-value | 1 | 1 | The value of the last object trap. |
| 1.3.6.1.4.1.5528.30.10.24 | netBotz-prd-bot-trap-date | 1 | 1 | The date and time of a specific trap. This field contains the number of seconds elapsed since midnight (00:00:00), January 1, 1970 |
| 1.3.6.1.4.1.5528.30.10.26 | netBotz-prd-bot-refresh | 1 | 1 | Rate of web page refresh, in seconds. This must be greater than 5 seconds. |
| 1.3.6.1.4.1.5528.30.10.27 | netBotz-prd-bot-airflow-level | 1 | 1 | Airflow alert level. This is the relative level of airflow below which an alarm will be sent. The range is 1-11. Each unit is… |
| 1.3.6.1.4.1.5528.30.10.28 | netBotz-prd-bot-doorpic-count | 1 | 1 | Number of pictures to take when door activated. These pictures will be sent as attachments to the door alert e-mail. The range is… |
| 1.3.6.1.4.1.5528.30.10.29 | netBotz-prd-bot-amps1 | 1 | 1 | The reading of the first amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.30 | netBotz-prd-bot-amps1-enabled | 1 | 1 | Amperage[1] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.31 | netBotz-prd-bot-amps1-min | 1 | 1 | The amperage[1] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.32 | netBotz-prd-bot-amps1-max | 1 | 1 | The amperage[1] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.34 | netBotz-prd-bot-amps2 | 1 | 1 | The reading of the second amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.35 | netBotz-prd-bot-amps2-enabled | 1 | 1 | Amperage[2] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.36 | netBotz-prd-bot-amps2-min | 1 | 1 | The amperage[2] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.37 | netBotz-prd-bot-amps2-max | 1 | 1 | The amperage[2] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.39 | netBotz-prd-bot-amps3 | 1 | 1 | The reading of the third amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.40 | netBotz-prd-bot-amps3-enabled | 1 | 1 | Amperage[3] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.41 | netBotz-prd-bot-amps3-min | 1 | 1 | The amperage[3] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.42 | netBotz-prd-bot-amps3-max | 1 | 1 | The amperage[3] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.44 | netBotz-prd-bot-amps-total | 1 | 1 | The total of the readings of all amperage probes, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.45 | netBotz-prd-bot-amps-total-enabled | 1 | 1 | Total amperage alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.46 | netBotz-prd-bot-amps-total-min | 1 | 1 | The total amperage minimum, from 0 to 90000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.47 | netBotz-prd-bot-amps-total-max | 1 | 1 | The total amperage maximum, from 0 to 90000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.48 | netBotz-prd-bot-amps-total-support-enabled | 1 | 1 | Total Amperage Support enabled(Y) or disabled(N). |
| 1.3.6.1.4.1.5528.30.10.49 | netBotz-prd-bot-amps1-uV-per-10mA | 1 | 1 | The scaling factor used for the first amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of… |
| 1.3.6.1.4.1.5528.30.10.50 | netBotz-prd-bot-amps2-uV-per-10mA | 1 | 1 | The scaling factor used for the second amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps o… |
| 1.3.6.1.4.1.5528.30.10.52 | netBotz-prd-bot-amps1-max-range | 1 | 1 | The maximum RMS milliamps measureable by the first Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.53 | netBotz-prd-bot-amps2-max-range | 1 | 1 | The maximum RMS milliamps measureable by the second Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.54 | netBotz-prd-bot-amps3-max-range | 1 | 1 | The maximum RMS milliamps measureable by the third Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.55 | netBotz-prd-bot-amps4 | 1 | 1 | The reading of the fourth amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.56 | netBotz-prd-bot-amps4-enabled | 1 | 1 | Amperage[4] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.57 | netBotz-prd-bot-amps4-min | 1 | 1 | The amperage[4] probe minimum, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.58 | netBotz-prd-bot-amps4-max | 1 | 1 | The amperage[4] probe maximum, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.60 | netBotz-prd-bot-amps4-uV-per-10mA | 1 | 1 | The scaling factor used for the fourth amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps o… |
| 1.3.6.1.4.1.5528.30.10.61 | netBotz-prd-bot-amps4-max-range | 1 | 1 | The maximum RMS milliamps measureable by the fourth Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.62 | netBotz-prd-bot-ext-temp1 | 1 | 1 | The reading of the external temperature probe on port 1, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.63 | netBotz-prd-bot-ext-temp2 | 1 | 1 | The reading of the external temperature probe on port 2, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.64 | netBotz-prd-bot-ext-temp3 | 1 | 1 | The reading of the external temperature probe on port 3, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.65 | netBotz-prd-bot-ext-temp4 | 1 | 1 | The reading of the external temperature probe on port 4, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.66 | netBotz-prd-bot-ext-temp1-enabled | 1 | 1 | External temperature probe on port 1 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.67 | netBotz-prd-bot-ext-temp1-min | 1 | 1 | The external temperature probe on port 1 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.68 | netBotz-prd-bot-ext-temp1-max | 1 | 1 | The external temperature probe on port 1 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.69 | netBotz-prd-bot-ext-temp2-enabled | 1 | 1 | External temperature probe on port 2 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.70 | netBotz-prd-bot-ext-temp2-min | 1 | 1 | The external temperature probe on port 2 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.71 | netBotz-prd-bot-ext-temp2-max | 1 | 1 | The external temperature probe on port 2 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.72 | netBotz-prd-bot-ext-temp3-enabled | 1 | 1 | External temperature probe on port 3 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.73 | netBotz-prd-bot-ext-temp3-min | 1 | 1 | The external temperature probe on port 3 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.74 | netBotz-prd-bot-ext-temp3-max | 1 | 1 | The external temperature probe on port 3 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.75 | netBotz-prd-bot-ext-temp4-enabled | 1 | 1 | External temperature probe on port 4 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.76 | netBotz-prd-bot-ext-temp4-min | 1 | 1 | The external temperature probe on port 4 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.77 | netBotz-prd-bot-ext-temp4-max | 1 | 1 | The external temperature probe on port 4 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.78 | netBotz-prd-bot-ext-temp1-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 1 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.79 | netBotz-prd-bot-ext-temp1-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 1 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.80 | netBotz-prd-bot-ext-temp1-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.81 | netBotz-prd-bot-ext-temp1-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.82 | netBotz-prd-bot-ext-temp2-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 2 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.83 | netBotz-prd-bot-ext-temp2-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 2 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.84 | netBotz-prd-bot-ext-temp2-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.85 | netBotz-prd-bot-ext-temp2-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.86 | netBotz-prd-bot-ext-temp3-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 3 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.87 | netBotz-prd-bot-ext-temp3-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 3 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.88 | netBotz-prd-bot-ext-temp3-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.89 | netBotz-prd-bot-ext-temp3-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.90 | netBotz-prd-bot-ext-temp4-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 4 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.91 | netBotz-prd-bot-ext-temp4-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 4 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.92 | netBotz-prd-bot-ext-temp4-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 4, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.93 | netBotz-prd-bot-ext-temp4-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 4, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.94 | netBotz-prd-bot-ext-port1-module-id | 1 | 1 | The module ID of the sensor module installed on port 1. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.95 | netBotz-prd-bot-ext-port1-module-type | 1 | 1 | The type of sensor module installed on port 1. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.96 | netBotz-prd-bot-ext-port2-module-id | 1 | 1 | The module ID of the sensor module installed on port 2. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.97 | netBotz-prd-bot-ext-port2-module-type | 1 | 1 | The type of sensor module installed on port 2. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.98 | netBotz-prd-bot-ext-port3-module-id | 1 | 1 | The module ID of the sensor module installed on port 3. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.99 | netBotz-prd-bot-ext-port3-module-type | 1 | 1 | The type of sensor module installed on port 3. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.100 | netBotz-prd-bot-ext-port4-module-id | 1 | 1 | The module ID of the sensor module installed on port 4. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.101 | netBotz-prd-bot-ext-port4-module-type | 1 | 1 | The type of sensor module installed on port 4. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| ... | ||||