External temperature probe on port 1 alarm enabled(1) or disabled(0).
Parsed from file netbotz2.mib.txt
Company: None
Module: NETBOTZ-MIB
External temperature probe on port 1 alarm enabled(1) or disabled(0).
Parsed from file NETBOTZ-MIB.mib
Module: NETBOTZ-MIB
Vendor: NetBotz
Module: NETBOTZ-PRD-BOT-MIB
[Automatically extracted from oidview.com]
netBotz-prd-bot-ext-temp1-enabled OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "External temperature probe on port 1 alarm enabled(1) or disabled(0)." REFERENCE "NetBotz|Ext Temp[1] Probe Enabled" ::= { netBotz-prd-bot 66 }
netBotz-prd-bot-ext-temp1-enabled OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "External temperature probe on port 1 alarm enabled(1) or disabled(0)." REFERENCE "NetBotz|Ext Temp[1] Probe Enabled" ::= { netBotz-prd-bot 66 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5528.30.10.66.0 | netBotz-prd-bot-ext-temp1-enabled | 0 | 0 | None |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.5528.30.10.16 | netBotz-prd-bot-switch-state | 1 | 1 | Switch state setting. The state controls which condition of the door switch indicates an alarm. If set to 0, alarm is set when th… |
| 1.3.6.1.4.1.5528.30.10.17 | netBotz-prd-bot-switch-enabled | 1 | 1 | Door switch enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.18 | netBotz-prd-bot-audio-level | 1 | 1 | Audio level setting. This is the relative audio level, from 0-11, above which an alarm will be sent. |
| 1.3.6.1.4.1.5528.30.10.19 | netBotz-prd-bot-doorpic-delay | 1 | 1 | Number of seconds between door alert and first picture. |
| 1.3.6.1.4.1.5528.30.10.20 | netBotz-prd-bot-trap-index | 1 | 1 | The crawler ID of the last trap. |
| 1.3.6.1.4.1.5528.30.10.21 | netBotz-prd-bot-trap-address | 1 | 1 | The IP address of the last trap. |
| 1.3.6.1.4.1.5528.30.10.22 | netBotz-prd-bot-trap-oid | 1 | 1 | The object id of the last trap. |
| 1.3.6.1.4.1.5528.30.10.23 | netBotz-prd-bot-trap-value | 1 | 1 | The value of the last object trap. |
| 1.3.6.1.4.1.5528.30.10.24 | netBotz-prd-bot-trap-date | 1 | 1 | The date and time of a specific trap. This field contains the number of seconds elapsed since midnight (00:00:00), January 1, 1970 |
| 1.3.6.1.4.1.5528.30.10.26 | netBotz-prd-bot-refresh | 1 | 1 | Rate of web page refresh, in seconds. This must be greater than 5 seconds. |
| 1.3.6.1.4.1.5528.30.10.27 | netBotz-prd-bot-airflow-level | 1 | 1 | Airflow alert level. This is the relative level of airflow below which an alarm will be sent. The range is 1-11. Each unit is… |
| 1.3.6.1.4.1.5528.30.10.28 | netBotz-prd-bot-doorpic-count | 1 | 1 | Number of pictures to take when door activated. These pictures will be sent as attachments to the door alert e-mail. The range is… |
| 1.3.6.1.4.1.5528.30.10.29 | netBotz-prd-bot-amps1 | 1 | 1 | The reading of the first amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.30 | netBotz-prd-bot-amps1-enabled | 1 | 1 | Amperage[1] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.31 | netBotz-prd-bot-amps1-min | 1 | 1 | The amperage[1] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.32 | netBotz-prd-bot-amps1-max | 1 | 1 | The amperage[1] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.34 | netBotz-prd-bot-amps2 | 1 | 1 | The reading of the second amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.35 | netBotz-prd-bot-amps2-enabled | 1 | 1 | Amperage[2] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.36 | netBotz-prd-bot-amps2-min | 1 | 1 | The amperage[2] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.37 | netBotz-prd-bot-amps2-max | 1 | 1 | The amperage[2] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.39 | netBotz-prd-bot-amps3 | 1 | 1 | The reading of the third amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.40 | netBotz-prd-bot-amps3-enabled | 1 | 1 | Amperage[3] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.41 | netBotz-prd-bot-amps3-min | 1 | 1 | The amperage[3] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.42 | netBotz-prd-bot-amps3-max | 1 | 1 | The amperage[3] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.44 | netBotz-prd-bot-amps-total | 1 | 1 | The total of the readings of all amperage probes, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.45 | netBotz-prd-bot-amps-total-enabled | 1 | 1 | Total amperage alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.46 | netBotz-prd-bot-amps-total-min | 1 | 1 | The total amperage minimum, from 0 to 90000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.47 | netBotz-prd-bot-amps-total-max | 1 | 1 | The total amperage maximum, from 0 to 90000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.48 | netBotz-prd-bot-amps-total-support-enabled | 1 | 1 | Total Amperage Support enabled(Y) or disabled(N). |
| 1.3.6.1.4.1.5528.30.10.49 | netBotz-prd-bot-amps1-uV-per-10mA | 1 | 1 | The scaling factor used for the first amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of… |
| 1.3.6.1.4.1.5528.30.10.50 | netBotz-prd-bot-amps2-uV-per-10mA | 1 | 1 | The scaling factor used for the second amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps o… |
| 1.3.6.1.4.1.5528.30.10.51 | netBotz-prd-bot-amps3-uV-per-mA | 1 | 1 | The scaling factor used for the third amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of… |
| 1.3.6.1.4.1.5528.30.10.52 | netBotz-prd-bot-amps1-max-range | 1 | 1 | The maximum RMS milliamps measureable by the first Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.53 | netBotz-prd-bot-amps2-max-range | 1 | 1 | The maximum RMS milliamps measureable by the second Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.54 | netBotz-prd-bot-amps3-max-range | 1 | 1 | The maximum RMS milliamps measureable by the third Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.55 | netBotz-prd-bot-amps4 | 1 | 1 | The reading of the fourth amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.56 | netBotz-prd-bot-amps4-enabled | 1 | 1 | Amperage[4] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.57 | netBotz-prd-bot-amps4-min | 1 | 1 | The amperage[4] probe minimum, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.58 | netBotz-prd-bot-amps4-max | 1 | 1 | The amperage[4] probe maximum, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.60 | netBotz-prd-bot-amps4-uV-per-10mA | 1 | 1 | The scaling factor used for the fourth amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps o… |
| 1.3.6.1.4.1.5528.30.10.61 | netBotz-prd-bot-amps4-max-range | 1 | 1 | The maximum RMS milliamps measureable by the fourth Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.62 | netBotz-prd-bot-ext-temp1 | 1 | 1 | The reading of the external temperature probe on port 1, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.63 | netBotz-prd-bot-ext-temp2 | 1 | 1 | The reading of the external temperature probe on port 2, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.64 | netBotz-prd-bot-ext-temp3 | 1 | 1 | The reading of the external temperature probe on port 3, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.65 | netBotz-prd-bot-ext-temp4 | 1 | 1 | The reading of the external temperature probe on port 4, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.67 | netBotz-prd-bot-ext-temp1-min | 1 | 1 | The external temperature probe on port 1 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.68 | netBotz-prd-bot-ext-temp1-max | 1 | 1 | The external temperature probe on port 1 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.69 | netBotz-prd-bot-ext-temp2-enabled | 1 | 1 | External temperature probe on port 2 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.70 | netBotz-prd-bot-ext-temp2-min | 1 | 1 | The external temperature probe on port 2 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.71 | netBotz-prd-bot-ext-temp2-max | 1 | 1 | The external temperature probe on port 2 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.72 | netBotz-prd-bot-ext-temp3-enabled | 1 | 1 | External temperature probe on port 3 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.73 | netBotz-prd-bot-ext-temp3-min | 1 | 1 | The external temperature probe on port 3 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.74 | netBotz-prd-bot-ext-temp3-max | 1 | 1 | The external temperature probe on port 3 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.75 | netBotz-prd-bot-ext-temp4-enabled | 1 | 1 | External temperature probe on port 4 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.76 | netBotz-prd-bot-ext-temp4-min | 1 | 1 | The external temperature probe on port 4 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.77 | netBotz-prd-bot-ext-temp4-max | 1 | 1 | The external temperature probe on port 4 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.78 | netBotz-prd-bot-ext-temp1-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 1 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.79 | netBotz-prd-bot-ext-temp1-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 1 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.80 | netBotz-prd-bot-ext-temp1-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.81 | netBotz-prd-bot-ext-temp1-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.82 | netBotz-prd-bot-ext-temp2-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 2 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.83 | netBotz-prd-bot-ext-temp2-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 2 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.84 | netBotz-prd-bot-ext-temp2-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.85 | netBotz-prd-bot-ext-temp2-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.86 | netBotz-prd-bot-ext-temp3-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 3 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.87 | netBotz-prd-bot-ext-temp3-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 3 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.88 | netBotz-prd-bot-ext-temp3-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.89 | netBotz-prd-bot-ext-temp3-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.90 | netBotz-prd-bot-ext-temp4-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 4 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.91 | netBotz-prd-bot-ext-temp4-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 4 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.92 | netBotz-prd-bot-ext-temp4-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 4, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.93 | netBotz-prd-bot-ext-temp4-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 4, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.94 | netBotz-prd-bot-ext-port1-module-id | 1 | 1 | The module ID of the sensor module installed on port 1. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.95 | netBotz-prd-bot-ext-port1-module-type | 1 | 1 | The type of sensor module installed on port 1. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.96 | netBotz-prd-bot-ext-port2-module-id | 1 | 1 | The module ID of the sensor module installed on port 2. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.97 | netBotz-prd-bot-ext-port2-module-type | 1 | 1 | The type of sensor module installed on port 2. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.98 | netBotz-prd-bot-ext-port3-module-id | 1 | 1 | The module ID of the sensor module installed on port 3. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.99 | netBotz-prd-bot-ext-port3-module-type | 1 | 1 | The type of sensor module installed on port 3. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.100 | netBotz-prd-bot-ext-port4-module-id | 1 | 1 | The module ID of the sensor module installed on port 4. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.101 | netBotz-prd-bot-ext-port4-module-type | 1 | 1 | The type of sensor module installed on port 4. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.102 | netBotz-prd-bot-amp1-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 1. |
| 1.3.6.1.4.1.5528.30.10.103 | netBotz-prd-bot-amp1-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 1. Writi… |
| 1.3.6.1.4.1.5528.30.10.104 | netBotz-prd-bot-amp2-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 2. |
| 1.3.6.1.4.1.5528.30.10.105 | netBotz-prd-bot-amp2-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 2. Writi… |
| 1.3.6.1.4.1.5528.30.10.106 | netBotz-prd-bot-amp3-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 3. |
| 1.3.6.1.4.1.5528.30.10.107 | netBotz-prd-bot-amp3-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 3. Writi… |
| 1.3.6.1.4.1.5528.30.10.108 | netBotz-prd-bot-amp4-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 4. |
| 1.3.6.1.4.1.5528.30.10.109 | netBotz-prd-bot-amp4-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 4. Writi… |
| 1.3.6.1.4.1.5528.30.10.110 | netBotz-prd-bot-amptotal-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the total of all AmpDetects. |
| 1.3.6.1.4.1.5528.30.10.111 | netBotz-prd-bot-amptotal-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds for all AmpDetects. Writing a val… |
| 1.3.6.1.4.1.5528.30.10.112 | netBotz-prd-bot-ext-dry1 | 1 | 1 | The current value of the external dry contact sensor on Ext1: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.113 | netBotz-prd-bot-ext-dry2 | 1 | 1 | The current value of the external dry contact sensor on Ext2: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.114 | netBotz-prd-bot-ext-dry3 | 1 | 1 | The current value of the external dry contact sensor on Ext3: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.115 | netBotz-prd-bot-ext-dry4 | 1 | 1 | The current value of the external dry contact sensor on Ext4: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.116 | netBotz-prd-bot-ext-dry1-alarm-value | 1 | 1 | The value to generate alarms on for the external dry contact sensor on Ext1: 0=Open, 1=Closed |
| ... | ||||