Vendor: NetBotz
Module: NETBOTZ-PRODUCTS-MIB
[Automatically extracted from oidview.com]
netBotz-prd-bot OBJECT IDENTIFIER ::= { netBotz-products 10 }
netBotz-prd-bot OBJECT IDENTIFIER ::= { netBotz-products 10 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5528.30.10.1 | netBotz-prd-bot-temp | 1 | 1 | The reading of the temperature probe, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.2 | netBotz-prd-bot-humidity | 1 | 1 | The reading of the humidity probe, in percent. |
| 1.3.6.1.4.1.5528.30.10.3 | netBotz-prd-bot-airflow | 1 | 1 | The reading of the airflow probe. Each unit represents approximately 40 feet/minute or 13 meters/minute of airflow velocity. |
| 1.3.6.1.4.1.5528.30.10.4 | netBotz-prd-bot-audio | 1 | 1 | The reading of the audio alarm probe on/off. |
| 1.3.6.1.4.1.5528.30.10.5 | netBotz-prd-bot-doorajar | 1 | 1 | The reading of the door switch probe open(1) or closed(0). |
| 1.3.6.1.4.1.5528.30.10.6 | netBotz-prd-bot-temp-min | 1 | 1 | The temperature probe minimum, from 35 to 120 degrees F, or 1 to 50 degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.7 | netBotz-prd-bot-temp-max | 1 | 1 | The temperature probe maximum, from 35 to 120 degrees F, or 1 to 50 degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.8 | netBotz-prd-bot-humidity-min | 1 | 1 | The humidity probe minimum, from 10 to 90 percent. |
| 1.3.6.1.4.1.5528.30.10.9 | netBotz-prd-bot-humidity-max | 1 | 1 | The humidity probe maximum, from 10 to 90 percent. |
| 1.3.6.1.4.1.5528.30.10.10 | netBotz-prd-bot-airflow-mins | 1 | 1 | Minutes without airflow before alarm set. |
| 1.3.6.1.4.1.5528.30.10.11 | netBotz-prd-bot-audio-secs | 1 | 1 | Seconds of alarm audio before alarm set. |
| 1.3.6.1.4.1.5528.30.10.12 | netBotz-prd-bot-temp-enabled | 1 | 1 | Temperature probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.13 | netBotz-prd-bot-hum-enabled | 1 | 1 | Humidity probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.14 | netBotz-prd-bot-air-enabled | 1 | 1 | Airflow probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.15 | netBotz-prd-bot-audio-enabled | 1 | 1 | Audio probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.16 | netBotz-prd-bot-switch-state | 1 | 1 | Switch state setting. The state controls which condition of the door switch indicates an alarm. If set to 0, alarm is set when th… |
| 1.3.6.1.4.1.5528.30.10.17 | netBotz-prd-bot-switch-enabled | 1 | 1 | Door switch enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.18 | netBotz-prd-bot-audio-level | 1 | 1 | Audio level setting. This is the relative audio level, from 0-11, above which an alarm will be sent. |
| 1.3.6.1.4.1.5528.30.10.19 | netBotz-prd-bot-doorpic-delay | 1 | 1 | Number of seconds between door alert and first picture. |
| 1.3.6.1.4.1.5528.30.10.20 | netBotz-prd-bot-trap-index | 1 | 1 | The crawler ID of the last trap. |
| 1.3.6.1.4.1.5528.30.10.21 | netBotz-prd-bot-trap-address | 1 | 1 | The IP address of the last trap. |
| 1.3.6.1.4.1.5528.30.10.22 | netBotz-prd-bot-trap-oid | 1 | 1 | The object id of the last trap. |
| 1.3.6.1.4.1.5528.30.10.23 | netBotz-prd-bot-trap-value | 1 | 1 | The value of the last object trap. |
| 1.3.6.1.4.1.5528.30.10.24 | netBotz-prd-bot-trap-date | 1 | 1 | The date and time of a specific trap. This field contains the number of seconds elapsed since midnight (00:00:00), January 1, 1970 |
| 1.3.6.1.4.1.5528.30.10.26 | netBotz-prd-bot-refresh | 1 | 1 | Rate of web page refresh, in seconds. This must be greater than 5 seconds. |
| 1.3.6.1.4.1.5528.30.10.27 | netBotz-prd-bot-airflow-level | 1 | 1 | Airflow alert level. This is the relative level of airflow below which an alarm will be sent. The range is 1-11. Each unit is… |
| 1.3.6.1.4.1.5528.30.10.28 | netBotz-prd-bot-doorpic-count | 1 | 1 | Number of pictures to take when door activated. These pictures will be sent as attachments to the door alert e-mail. The range is… |
| 1.3.6.1.4.1.5528.30.10.29 | netBotz-prd-bot-amps1 | 1 | 1 | The reading of the first amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.30 | netBotz-prd-bot-amps1-enabled | 1 | 1 | Amperage[1] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.31 | netBotz-prd-bot-amps1-min | 1 | 1 | The amperage[1] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.32 | netBotz-prd-bot-amps1-max | 1 | 1 | The amperage[1] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.34 | netBotz-prd-bot-amps2 | 1 | 1 | The reading of the second amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.35 | netBotz-prd-bot-amps2-enabled | 1 | 1 | Amperage[2] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.36 | netBotz-prd-bot-amps2-min | 1 | 1 | The amperage[2] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.37 | netBotz-prd-bot-amps2-max | 1 | 1 | The amperage[2] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.39 | netBotz-prd-bot-amps3 | 1 | 1 | The reading of the third amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.40 | netBotz-prd-bot-amps3-enabled | 1 | 1 | Amperage[3] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.41 | netBotz-prd-bot-amps3-min | 1 | 1 | The amperage[3] probe minimum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.42 | netBotz-prd-bot-amps3-max | 1 | 1 | The amperage[3] probe maximum, from 0 to 30000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.44 | netBotz-prd-bot-amps-total | 1 | 1 | The total of the readings of all amperage probes, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.45 | netBotz-prd-bot-amps-total-enabled | 1 | 1 | Total amperage alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.46 | netBotz-prd-bot-amps-total-min | 1 | 1 | The total amperage minimum, from 0 to 90000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.47 | netBotz-prd-bot-amps-total-max | 1 | 1 | The total amperage maximum, from 0 to 90000 milliamps. |
| 1.3.6.1.4.1.5528.30.10.48 | netBotz-prd-bot-amps-total-support-enabled | 1 | 1 | Total Amperage Support enabled(Y) or disabled(N). |
| 1.3.6.1.4.1.5528.30.10.49 | netBotz-prd-bot-amps1-uV-per-10mA | 1 | 1 | The scaling factor used for the first amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of… |
| 1.3.6.1.4.1.5528.30.10.50 | netBotz-prd-bot-amps2-uV-per-10mA | 1 | 1 | The scaling factor used for the second amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps o… |
| 1.3.6.1.4.1.5528.30.10.51 | netBotz-prd-bot-amps3-uV-per-mA | 1 | 1 | The scaling factor used for the third amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps of… |
| 1.3.6.1.4.1.5528.30.10.52 | netBotz-prd-bot-amps1-max-range | 1 | 1 | The maximum RMS milliamps measureable by the first Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.53 | netBotz-prd-bot-amps2-max-range | 1 | 1 | The maximum RMS milliamps measureable by the second Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.54 | netBotz-prd-bot-amps3-max-range | 1 | 1 | The maximum RMS milliamps measureable by the third Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.55 | netBotz-prd-bot-amps4 | 1 | 1 | The reading of the fourth amperage probe, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.56 | netBotz-prd-bot-amps4-enabled | 1 | 1 | Amperage[4] probe alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.57 | netBotz-prd-bot-amps4-min | 1 | 1 | The amperage[4] probe minimum, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.58 | netBotz-prd-bot-amps4-max | 1 | 1 | The amperage[4] probe maximum, in milliamps. |
| 1.3.6.1.4.1.5528.30.10.60 | netBotz-prd-bot-amps4-uV-per-10mA | 1 | 1 | The scaling factor used for the fourth amperage probe to convert microvolts measured from the Amp Detect into 10s of milliamps o… |
| 1.3.6.1.4.1.5528.30.10.61 | netBotz-prd-bot-amps4-max-range | 1 | 1 | The maximum RMS milliamps measureable by the fourth Amp Detect. |
| 1.3.6.1.4.1.5528.30.10.62 | netBotz-prd-bot-ext-temp1 | 1 | 1 | The reading of the external temperature probe on port 1, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.63 | netBotz-prd-bot-ext-temp2 | 1 | 1 | The reading of the external temperature probe on port 2, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.64 | netBotz-prd-bot-ext-temp3 | 1 | 1 | The reading of the external temperature probe on port 3, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.65 | netBotz-prd-bot-ext-temp4 | 1 | 1 | The reading of the external temperature probe on port 4, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.66 | netBotz-prd-bot-ext-temp1-enabled | 1 | 1 | External temperature probe on port 1 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.67 | netBotz-prd-bot-ext-temp1-min | 1 | 1 | The external temperature probe on port 1 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.68 | netBotz-prd-bot-ext-temp1-max | 1 | 1 | The external temperature probe on port 1 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.69 | netBotz-prd-bot-ext-temp2-enabled | 1 | 1 | External temperature probe on port 2 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.70 | netBotz-prd-bot-ext-temp2-min | 1 | 1 | The external temperature probe on port 2 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.71 | netBotz-prd-bot-ext-temp2-max | 1 | 1 | The external temperature probe on port 2 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.72 | netBotz-prd-bot-ext-temp3-enabled | 1 | 1 | External temperature probe on port 3 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.73 | netBotz-prd-bot-ext-temp3-min | 1 | 1 | The external temperature probe on port 3 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.74 | netBotz-prd-bot-ext-temp3-max | 1 | 1 | The external temperature probe on port 3 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.75 | netBotz-prd-bot-ext-temp4-enabled | 1 | 1 | External temperature probe on port 4 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.76 | netBotz-prd-bot-ext-temp4-min | 1 | 1 | The external temperature probe on port 4 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.77 | netBotz-prd-bot-ext-temp4-max | 1 | 1 | The external temperature probe on port 4 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). |
| 1.3.6.1.4.1.5528.30.10.78 | netBotz-prd-bot-ext-temp1-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 1 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.79 | netBotz-prd-bot-ext-temp1-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 1 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.80 | netBotz-prd-bot-ext-temp1-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.81 | netBotz-prd-bot-ext-temp1-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.82 | netBotz-prd-bot-ext-temp2-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 2 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.83 | netBotz-prd-bot-ext-temp2-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 2 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.84 | netBotz-prd-bot-ext-temp2-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.85 | netBotz-prd-bot-ext-temp2-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.86 | netBotz-prd-bot-ext-temp3-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 3 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.87 | netBotz-prd-bot-ext-temp3-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 3 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.88 | netBotz-prd-bot-ext-temp3-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.89 | netBotz-prd-bot-ext-temp3-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.90 | netBotz-prd-bot-ext-temp4-uV-per-degreeC | 1 | 1 | The scaling factor used for the external temperature probe on port 4 to convert microvolts measured from the temperature sensor … |
| 1.3.6.1.4.1.5528.30.10.91 | netBotz-prd-bot-ext-temp4-uV-at-0-degreeC | 1 | 1 | The offset used for the external temperature probe on port 4 of microvolts measured from the temperature sensor at zero degrees … |
| 1.3.6.1.4.1.5528.30.10.92 | netBotz-prd-bot-ext-temp4-min-range | 1 | 1 | The minimum temperature measureable by the temperature sensor installed on port 4, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.93 | netBotz-prd-bot-ext-temp4-max-range | 1 | 1 | The maximum temperature measureable by the temperature sensor installed on port 4, in tenths of a degree C. Needs to be set base… |
| 1.3.6.1.4.1.5528.30.10.94 | netBotz-prd-bot-ext-port1-module-id | 1 | 1 | The module ID of the sensor module installed on port 1. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.95 | netBotz-prd-bot-ext-port1-module-type | 1 | 1 | The type of sensor module installed on port 1. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.96 | netBotz-prd-bot-ext-port2-module-id | 1 | 1 | The module ID of the sensor module installed on port 2. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.97 | netBotz-prd-bot-ext-port2-module-type | 1 | 1 | The type of sensor module installed on port 2. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.98 | netBotz-prd-bot-ext-port3-module-id | 1 | 1 | The module ID of the sensor module installed on port 3. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.99 | netBotz-prd-bot-ext-port3-module-type | 1 | 1 | The type of sensor module installed on port 3. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.100 | netBotz-prd-bot-ext-port4-module-id | 1 | 1 | The module ID of the sensor module installed on port 4. Blank string indicates that no module is installed. |
| 1.3.6.1.4.1.5528.30.10.101 | netBotz-prd-bot-ext-port4-module-type | 1 | 1 | The type of sensor module installed on port 4. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact … |
| 1.3.6.1.4.1.5528.30.10.102 | netBotz-prd-bot-amp1-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 1. |
| 1.3.6.1.4.1.5528.30.10.103 | netBotz-prd-bot-amp1-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 1. Writi… |
| 1.3.6.1.4.1.5528.30.10.104 | netBotz-prd-bot-amp2-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 2. |
| 1.3.6.1.4.1.5528.30.10.105 | netBotz-prd-bot-amp2-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 2. Writi… |
| 1.3.6.1.4.1.5528.30.10.106 | netBotz-prd-bot-amp3-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 3. |
| 1.3.6.1.4.1.5528.30.10.107 | netBotz-prd-bot-amp3-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 3. Writi… |
| 1.3.6.1.4.1.5528.30.10.108 | netBotz-prd-bot-amp4-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the AmpDetect on port 4. |
| 1.3.6.1.4.1.5528.30.10.109 | netBotz-prd-bot-amp4-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 4. Writi… |
| 1.3.6.1.4.1.5528.30.10.110 | netBotz-prd-bot-amptotal-total-amp-seconds | 1 | 1 | The accumulated total of amp-seconds on the total of all AmpDetects. |
| 1.3.6.1.4.1.5528.30.10.111 | netBotz-prd-bot-amptotal-total-amp-seconds-since-time | 1 | 1 | The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds for all AmpDetects. Writing a val… |
| 1.3.6.1.4.1.5528.30.10.112 | netBotz-prd-bot-ext-dry1 | 1 | 1 | The current value of the external dry contact sensor on Ext1: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.113 | netBotz-prd-bot-ext-dry2 | 1 | 1 | The current value of the external dry contact sensor on Ext2: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.114 | netBotz-prd-bot-ext-dry3 | 1 | 1 | The current value of the external dry contact sensor on Ext3: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.115 | netBotz-prd-bot-ext-dry4 | 1 | 1 | The current value of the external dry contact sensor on Ext4: 0=Open, 1=Closed, -1=N/A |
| 1.3.6.1.4.1.5528.30.10.116 | netBotz-prd-bot-ext-dry1-alarm-value | 1 | 1 | The value to generate alarms on for the external dry contact sensor on Ext1: 0=Open, 1=Closed |
| 1.3.6.1.4.1.5528.30.10.117 | netBotz-prd-bot-ext-dry1-enabled | 1 | 1 | External dry contact sensor on Ext1 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.118 | netBotz-prd-bot-ext-dry2-alarm-value | 1 | 1 | The value to generate alarms on for the external dry contact sensor on Ext2: 0=Open, 1=Closed |
| 1.3.6.1.4.1.5528.30.10.119 | netBotz-prd-bot-ext-dry2-enabled | 1 | 1 | External dry contact sensor on Ext2 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.120 | netBotz-prd-bot-ext-dry3-alarm-value | 1 | 1 | The value to generate alarms on for the external dry contact sensor on Ext3: 0=Open, 1=Closed |
| 1.3.6.1.4.1.5528.30.10.121 | netBotz-prd-bot-ext-dry3-enabled | 1 | 1 | External dry contact sensor on Ext3 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.122 | netBotz-prd-bot-ext-dry4-alarm-value | 1 | 1 | The value to generate alarms on for the external dry contact sensor on Ext4: 0=Open, 1=Closed |
| 1.3.6.1.4.1.5528.30.10.123 | netBotz-prd-bot-ext-dry4-enabled | 1 | 1 | External dry contact sensor on Ext4 alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.124 | netBotz-prd-bot-ext-dry1-label | 1 | 1 | The sensor name/label for the dry contact sensor on Ext1 |
| 1.3.6.1.4.1.5528.30.10.125 | netBotz-prd-bot-ext-dry1-open-label | 1 | 1 | The sensor name/label for the open(0) state for the dry contact sensor on Ext1 |
| 1.3.6.1.4.1.5528.30.10.126 | netBotz-prd-bot-ext-dry1-closed-label | 1 | 1 | The sensor name/label for the closed(0) state for the dry contact sensor on Ext1 |
| 1.3.6.1.4.1.5528.30.10.127 | netBotz-prd-bot-ext-dry1-open-to-close-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext1 must read closed before the state is changed from open to… |
| 1.3.6.1.4.1.5528.30.10.128 | netBotz-prd-bot-ext-dry1-close-to-open-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext1 must read openbefore the state is changed from closed to … |
| 1.3.6.1.4.1.5528.30.10.129 | netBotz-prd-bot-ext-dry1-response | 1 | 1 | The type of alert response for the dry contact sensor on Ext1: ALERT=e-mail with no pictures, CAMERA=e-mail with pictures from c… |
| 1.3.6.1.4.1.5528.30.10.130 | netBotz-prd-bot-ext-dry2-label | 1 | 1 | The sensor name/label for the dry contact sensor on Ext2 |
| 1.3.6.1.4.1.5528.30.10.131 | netBotz-prd-bot-ext-dry2-open-label | 1 | 1 | The sensor name/label for the open(0) state for the dry contact sensor on Ext2 |
| 1.3.6.1.4.1.5528.30.10.132 | netBotz-prd-bot-ext-dry2-closed-label | 1 | 1 | The sensor name/label for the closed(0) state for the dry contact sensor on Ext2 |
| 1.3.6.1.4.1.5528.30.10.133 | netBotz-prd-bot-ext-dry2-open-to-close-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext2 must read closed before the state is changed from open to… |
| 1.3.6.1.4.1.5528.30.10.134 | netBotz-prd-bot-ext-dry2-close-to-open-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext2 must read openbefore the state is changed from closed to … |
| 1.3.6.1.4.1.5528.30.10.135 | netBotz-prd-bot-ext-dry2-response | 1 | 1 | The type of alert response for the dry contact sensor on Ext2: ALERT=e-mail with no pictures, CAMERA=e-mail with pictures from c… |
| 1.3.6.1.4.1.5528.30.10.136 | netBotz-prd-bot-ext-dry3-label | 1 | 1 | The sensor name/label for the dry contact sensor on Ext3 |
| 1.3.6.1.4.1.5528.30.10.137 | netBotz-prd-bot-ext-dry3-open-label | 1 | 1 | The sensor name/label for the open(0) state for the dry contact sensor on Ext3 |
| 1.3.6.1.4.1.5528.30.10.138 | netBotz-prd-bot-ext-dry3-closed-label | 1 | 1 | The sensor name/label for the closed(0) state for the dry contact sensor on Ext3 |
| 1.3.6.1.4.1.5528.30.10.139 | netBotz-prd-bot-ext-dry3-open-to-close-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext3 must read closed before the state is changed from open to… |
| 1.3.6.1.4.1.5528.30.10.140 | netBotz-prd-bot-ext-dry3-close-to-open-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext3 must read openbefore the state is changed from closed to … |
| 1.3.6.1.4.1.5528.30.10.141 | netBotz-prd-bot-ext-dry3-response | 1 | 1 | The type of alert response for the dry contact sensor on Ext3: ALERT=e-mail with no pictures, CAMERA=e-mail with pictures from c… |
| 1.3.6.1.4.1.5528.30.10.142 | netBotz-prd-bot-ext-dry4-label | 1 | 1 | The sensor name/label for the dry contact sensor on Ext4 |
| 1.3.6.1.4.1.5528.30.10.143 | netBotz-prd-bot-ext-dry4-open-label | 1 | 1 | The sensor name/label for the open(0) state for the dry contact sensor on Ext4 |
| 1.3.6.1.4.1.5528.30.10.144 | netBotz-prd-bot-ext-dry4-closed-label | 1 | 1 | The sensor name/label for the closed(0) state for the dry contact sensor on Ext4 |
| 1.3.6.1.4.1.5528.30.10.145 | netBotz-prd-bot-ext-dry4-open-to-close-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext4 must read closed before the state is changed from open to… |
| 1.3.6.1.4.1.5528.30.10.146 | netBotz-prd-bot-ext-dry4-close-to-open-millis | 1 | 1 | The minimum number of milliseconds that the dry contact sensor on Ext4 must read openbefore the state is changed from closed to … |
| 1.3.6.1.4.1.5528.30.10.147 | netBotz-prd-bot-ext-dry4-response | 1 | 1 | The type of alert response for the dry contact sensor on Ext4: ALERT=e-mail with no pictures, CAMERA=e-mail with pictures from c… |
| 1.3.6.1.4.1.5528.30.10.148 | netBotz-prd-bot-cam-motion | 1 | 1 | The current motion reading for the camera motion sensor (0=none, 1=motion detected) |
| 1.3.6.1.4.1.5528.30.10.149 | netBotz-prd-bot-cam-motion-enabled | 1 | 1 | Camera motion sensor alarm enabled(1) or disabled(0). |
| 1.3.6.1.4.1.5528.30.10.150 | netBotz-prd-bot-cam-motion-sensitivity | 1 | 1 | Camera motion sensor sensitivity: 1=max, 15=min, 0=disabled. |
| 1.3.6.1.4.1.5528.30.10.151 | netBotz-prd-bot-cam-motion-delay | 1 | 1 | Camera motion sensor delay. This is the minimum number of milliseconds of detected motion required before the alarm is triggere… |
| 1.3.6.1.4.1.5528.30.10.152 | netBotz-prd-bot-camera-event-autocycle | 1 | 1 | Enables (1) or disables (0) the option to have the camera-based responses to alarm conditions automatically cycle as long as the… |
| 1.3.6.1.4.1.5528.30.10.153 | netBotz-prd-bot-num-pix-before-alarm | 1 | 1 | Controls the number of pictures to be captured before any triggered alarm. |
| 1.3.6.1.4.1.5528.30.10.154 | netBotz-prd-bot-delay-before-event-pix | 1 | 1 | Controls the number of milliseconds before the first picture is captured after any triggered alarm. |
| 1.3.6.1.4.1.5528.30.10.155 | netBotz-prd-bot-delay-between-event-pix | 1 | 1 | Controls the number of milliseconds between pictures captured after any triggered alarm. |
| 1.3.6.1.4.1.5528.30.10.156 | netBotz-prd-bot-cam-motion-area-of-motion | 1 | 1 | Camera motion sensor area of motion: 1=max, 15=min, 0=disabled. |
| 1.3.6.1.4.1.5528.30.10.157 | netBotz-prd-bot-cam-pix-for-duration-of-alerts | 1 | 1 | Camera images gathered for duration of camera related alert: 0=no, 1=yes. |
| 1.3.6.1.4.1.5528.30.10.158 | netBotz-prd-bot-camera-enabled | 1 | 1 | Controls whether the camera is enabled or not: 0=no, 1=yes. Changing this will reboot the appliance. |
| 1.3.6.1.4.1.5528.30.10.159 | netBotz-prd-bot-camera-is-flipped | 1 | 1 | Controls whether the camera image is flipped 180 degress or not: 0=no, 1=yes. Changing this will reboot the appliance. |
| 1.3.6.1.4.1.5528.30.10.160 | netBotz-prd-bot-camera-brightness | 1 | 1 | Sets the brightness on the camera, from 20 to 180 (20 is low, 180 is high). |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5528.30.20 | netBotz-prd-crawlers | 1 | 19 | None |
| 1.3.6.1.4.1.5528.30.21 | netBotz-prd-crltrap | 8 | 16 | None |
| 1.3.6.1.4.1.5528.30.100 | netBotz-prd-bot-traps | 35 | 98 | None |
| 1.3.6.1.4.1.5528.30.1000 | netBotz-prd-WallBotz-300 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1001 | netBotz-prd-RackBotz-300 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1002 | netBotz-prd-RackBotz-300U | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1003 | netBotz-prd-WallBotz-400 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1004 | netBotz-prd-RackBotz-400 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1006 | netBotz-prd-RackBotz-303 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1007 | netBotz-prd-WallBotz-310 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1008 | netBotz-prd-RackBotz-310 | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1009 | netBotz-prd-WallBotz-300B | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1100 | netBotz-prd-WallBotz-300C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1101 | netBotz-prd-RackBotz-300C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1102 | netBotz-prd-RackBotz-300UC | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1103 | netBotz-prd-WallBotz-400C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1104 | netBotz-prd-RackBotz-400C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1106 | netBotz-prd-RackBotz-303C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1107 | netBotz-prd-WallBotz-310C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1108 | netBotz-prd-RackBotz-310C | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1109 | netBotz-prd-WallBotz-300BC | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1200 | netBotz-prd-WallBotz-300E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1201 | netBotz-prd-RackBotz-300E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1202 | netBotz-prd-RackBotz-300UE | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1203 | netBotz-prd-WallBotz-400E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1204 | netBotz-prd-RackBotz-400E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1206 | netBotz-prd-RackBotz-303E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1207 | netBotz-prd-WallBotz-310E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1208 | netBotz-prd-RackBotz-310E | 0 | 0 | None |
| 1.3.6.1.4.1.5528.30.1209 | netBotz-prd-WallBotz-300BE | 0 | 0 | None |