tmnxDS1ClockSource configures the clock for transmitted data from
either the internal clock ('nodeTimed'), or from a clock recovered
from the line's receive data stream ('loopTimed'), or recovered
adaptively from the rate at which the data that is received and not
from the physical layer ('adaptive'), or recovered from the
differential timestamp in the RTP header ('differential').
Parsed from file TIMETRA-PORT-MIB.mib
Module: TIMETRA-PORT-MIB
tmnxDS1ClockSource OBJECT-TYPE SYNTAX TmnxDSXClockSource MAX-ACCESS read-create STATUS current DESCRIPTION "tmnxDS1ClockSource configures the clock for transmitted data from either the internal clock ('nodeTimed'), or from a clock recovered from the line's receive data stream ('loopTimed'), or recovered adaptively from the rate at which the data that is received and not from the physical layer ('adaptive'), or recovered from the differential timestamp in the RTP header ('differential')." DEFVAL { loopTimed } ::= { tmnxDS1Entry 13 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.1 | tmnxDS1RowStatus | 0 | 0 | tmnxDS1RowStatus controls the creation and deletion of row entries in the tmnxDS1Table. For row creation, the manager has to firs… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.2 | tmnxDS1Type | 0 | 0 | The value of tmnxDS1Type indicates whether the DS1 channel is in DS1, E1 or J1 mode. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.3 | tmnxDS1Framing | 0 | 0 | The value of tmnxDS1Framing indicates the type of framing associated with the channel: esf ESF (extended super frame) … |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.4 | tmnxDS1IdleCycleFlags | 0 | 0 | tmnxDS1IdleCycleFlags configures the value that the DS1 channel transmits during idle cycle. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.5 | tmnxDS1Loopback | 0 | 0 | tmnxDS1Loopback is used to put the channel into a loopback mode. The value of tmnxPortAdminStatus should be set to 'outOfService… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.6 | tmnxDS1InvertData | 0 | 0 | Setting tmnxDS1InvertData to 'true' causes all data bits to be inverted, to guarantee ones density. It is typically used with AMI… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.7 | tmnxDS1BitErrorInsertionRate | 0 | 0 | tmnxDS1BitErrorInsertionRate is used to insert bit errors for a BERT test. The number of error corresponds to 10^(-rate). A rate… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.8 | tmnxDS1BERTPattern | 0 | 0 | tmnxDS1BERTPattern object indicates the pattern used for the Bit Error Rate Test (BERT). The value of tmnxDS1BERTDuration indicat… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.9 | tmnxDS1BERTDuration | 0 | 0 | tmnxDS1BERTDuration is used to set the duration of the BERT test. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.10 | tmnxDS1ReportAlarm | 0 | 0 | The value of tmnxDS1ReportAlarm determines when and if to generate notifications for this channel: ais - Reports alarm indication… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.11 | tmnxDS1ReportAlarmStatus | 0 | 0 | The value of tmnxDS1ReportAlarmStatus indicates the current alarms on this channel. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.12 | tmnxDS1LastChangeTime | 0 | 0 | The tmnxDS1LastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS1Ent… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.14 | tmnxDS1BERTOperStatus | 0 | 0 | tmnxDS1BERTOperStatus indicates the status of the BERT test as specified by TmnxDSXBertOperStatus. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.15 | tmnxDS1BERTSynched | 0 | 0 | tmnxDS1BERTSynched is the number of seconds for which the BERT hardware was synchronized. This will be less than or equal to the … |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.16 | tmnxDS1BERTErrors | 0 | 0 | tmnxDS1BERTErrors is the number of bit errors detected during the last BERT test. It is valid only after tmnxDS1BERTOperStatus tr… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.17 | tmnxDS1BERTTotalBits | 0 | 0 | tmnxDS1BERTTotalBits is the total number of bits received during the last BERT test. Bits are only counted when the BERT hardware… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.18 | tmnxDS1RemoteLoopRespond | 0 | 0 | When tmnxDS1RemoteLoopRespond has a value of 'true', the channel is enabled to respond to remote loop signals. When it has a val… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.19 | tmnxDS1InRemoteLoop | 0 | 0 | tmnxDS1InRemoteLoop indicates whether the remote end has put this channel in remote loopback. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.20 | tmnxDS1InsertSingleBitError | 0 | 0 | tmnxDS1InsertSingleBitError is used to insert a single bit error for a BERT test. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.21 | tmnxDS1SignalMode | 0 | 0 | The value of tmnxDS1SignalMode indicates the type of signalling associated with the channel: none - Indicates no signalling on t… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.22 | tmnxDS1ClockSyncState | 0 | 0 | The value of tmnxDS1ClockSyncState indicates the current clock synchronization state if tmnxDS1ClockSource is 'adaptive' or 'diff… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.23 | tmnxDS1ClockMasterPortId | 0 | 0 | The value of tmnxDS1ClockMasterPortId indicates the current clock synchronization master port id if tmnxDS1ClockSource is 'adapt… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.24 | tmnxDS1BerSdThreshold | 0 | 0 | The value of tmnxDS1BerSdThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortDS1Alar… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.25 | tmnxDS1BerSfThreshold | 0 | 0 | The value of tmnxDS1BerSfThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortDS1Alar… |