tmnxDS1BERTDuration is used to set the duration of the BERT test.
Parsed from file TIMETRA-PORT-MIB.mib
Module: TIMETRA-PORT-MIB
tmnxDS1BERTDuration OBJECT-TYPE SYNTAX Unsigned32 (0..86400) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "tmnxDS1BERTDuration is used to set the duration of the BERT test." ::= { tmnxDS1Entry 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.1 | tmnxDS1RowStatus | 0 | 0 | tmnxDS1RowStatus controls the creation and deletion of row entries in the tmnxDS1Table. For row creation, the manager has to firs… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.2 | tmnxDS1Type | 0 | 0 | The value of tmnxDS1Type indicates whether the DS1 channel is in DS1, E1 or J1 mode. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.3 | tmnxDS1Framing | 0 | 0 | The value of tmnxDS1Framing indicates the type of framing associated with the channel: esf ESF (extended super frame) … |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.4 | tmnxDS1IdleCycleFlags | 0 | 0 | tmnxDS1IdleCycleFlags configures the value that the DS1 channel transmits during idle cycle. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.5 | tmnxDS1Loopback | 0 | 0 | tmnxDS1Loopback is used to put the channel into a loopback mode. The value of tmnxPortAdminStatus should be set to 'outOfService… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.6 | tmnxDS1InvertData | 0 | 0 | Setting tmnxDS1InvertData to 'true' causes all data bits to be inverted, to guarantee ones density. It is typically used with AMI… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.7 | tmnxDS1BitErrorInsertionRate | 0 | 0 | tmnxDS1BitErrorInsertionRate is used to insert bit errors for a BERT test. The number of error corresponds to 10^(-rate). A rate… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.8 | tmnxDS1BERTPattern | 0 | 0 | tmnxDS1BERTPattern object indicates the pattern used for the Bit Error Rate Test (BERT). The value of tmnxDS1BERTDuration indicat… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.10 | tmnxDS1ReportAlarm | 0 | 0 | The value of tmnxDS1ReportAlarm determines when and if to generate notifications for this channel: ais - Reports alarm indication… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.11 | tmnxDS1ReportAlarmStatus | 0 | 0 | The value of tmnxDS1ReportAlarmStatus indicates the current alarms on this channel. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.12 | tmnxDS1LastChangeTime | 0 | 0 | The tmnxDS1LastChangeTime variable contains the sysUpTime value of the most recently modified writable variable in the tmnxDS1Ent… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.13 | tmnxDS1ClockSource | 0 | 0 | tmnxDS1ClockSource configures the clock for transmitted data from either the internal clock ('nodeTimed'), or from a clock recov… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.14 | tmnxDS1BERTOperStatus | 0 | 0 | tmnxDS1BERTOperStatus indicates the status of the BERT test as specified by TmnxDSXBertOperStatus. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.15 | tmnxDS1BERTSynched | 0 | 0 | tmnxDS1BERTSynched is the number of seconds for which the BERT hardware was synchronized. This will be less than or equal to the … |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.16 | tmnxDS1BERTErrors | 0 | 0 | tmnxDS1BERTErrors is the number of bit errors detected during the last BERT test. It is valid only after tmnxDS1BERTOperStatus tr… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.17 | tmnxDS1BERTTotalBits | 0 | 0 | tmnxDS1BERTTotalBits is the total number of bits received during the last BERT test. Bits are only counted when the BERT hardware… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.18 | tmnxDS1RemoteLoopRespond | 0 | 0 | When tmnxDS1RemoteLoopRespond has a value of 'true', the channel is enabled to respond to remote loop signals. When it has a val… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.19 | tmnxDS1InRemoteLoop | 0 | 0 | tmnxDS1InRemoteLoop indicates whether the remote end has put this channel in remote loopback. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.20 | tmnxDS1InsertSingleBitError | 0 | 0 | tmnxDS1InsertSingleBitError is used to insert a single bit error for a BERT test. |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.21 | tmnxDS1SignalMode | 0 | 0 | The value of tmnxDS1SignalMode indicates the type of signalling associated with the channel: none - Indicates no signalling on t… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.22 | tmnxDS1ClockSyncState | 0 | 0 | The value of tmnxDS1ClockSyncState indicates the current clock synchronization state if tmnxDS1ClockSource is 'adaptive' or 'diff… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.23 | tmnxDS1ClockMasterPortId | 0 | 0 | The value of tmnxDS1ClockMasterPortId indicates the current clock synchronization master port id if tmnxDS1ClockSource is 'adapt… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.24 | tmnxDS1BerSdThreshold | 0 | 0 | The value of tmnxDS1BerSdThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortDS1Alar… |
| 1.3.6.1.4.1.6527.3.1.2.2.4.12.1.25 | tmnxDS1BerSfThreshold | 0 | 0 | The value of tmnxDS1BerSfThreshold specifies a bit error rate (BER) threshold used to determine when to send a tmnxEqPortDS1Alar… |