OID reference
1.3.6.1.4.1.9839.2.1.3.47
Humidifier Runtime - low
Identification
{1 3 6 1 4 1 9839 2 1 3 47}
Definitions may combine these properties differently.
At least one MIB declaration places this object in a scalar group. A scalar instance uses the suffix .0.
snmpget [connection options] DEVICE .1.3.6.1.4.1.9839.2.1.3.47.0
Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.
Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.
Available source records contain 10 distinct definitions; some records may not include a definition.
delay-Freecooling OBJECT-TYPE
SYNTAX Integer32 (0..9999)
UNITS "N/A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Delay Freecooling"
::= { integerObjects 47 }intervallo_tra_pulizie OBJECT-TYPE
SYNTAX Integer32 (1..999)
UNITS "hours"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Time between two successive cleanings"
DEFVAL { 1 }
::= { integerObjects 47 }defrost_t3_hh OBJECT-TYPE
SYNTAX Integer32 (0..23)
UNITS "ore"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Defrost event 3 hour"
::= { integerObjects 47 }rit_dif_olio OBJECT-TYPE
SYNTAX Integer32 (0..360)
UNITS "sec"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Delay in oil differential alarm at start"
DEFVAL { 90 }
::= { integerObjects 47 }ist_parz2_es OBJECT-TYPE
SYNTAX Integer32 (0..100)
UNITS "%"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Capacity control 2 hysteresis with energy saving"
DEFVAL { 100 }
::= { integerObjects 47 }hum-hours-l OBJECT-TYPE
SYNTAX Integer32 (-32768..32767)
UNITS "hour"
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Humidifier Runtime - low"
DEFVAL { 0 }
::= { integerObjects 47 }defrost_t4_mm OBJECT-TYPE
SYNTAX Integer32 (0..59)
UNITS "min"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Defrost event 4th min"
::= { integerObjects 47 }f15 OBJECT-TYPE
SYNTAX Integer32 (0..99)
UNITS "min"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Air stirring active duration."
DEFVAL { 0 }
::= { integerObjects 47 }n_partial OBJECT-TYPE
SYNTAX Integer32 (0..3)
UNITS "N/A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Number of voltage variations"
DEFVAL { 1 }
::= { integerObjects 47 }postdef_dr_t_dd OBJECT-TYPE
SYNTAX Integer32 (0..15)
UNITS "min"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "post-defrost dripping time"
DEFVAL { 2 }
::= { integerObjects 47 }
Meaning
Identical descriptions are grouped. Different wording and device-specific notes are retained.
Description 1
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 2
Delay Freecooling
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 3
Time between two successive cleanings
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 4
Defrost event 3 hour
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 5
Delay in oil differential alarm at start
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 6
Capacity control 2 hysteresis with energy saving
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 7
Defrost event 4th min
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 8
Air stirring active duration.
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 9
Number of voltage variations
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 10
post-defrost dripping time
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Evidence
Matching descriptions are grouped; open a group to compare definitions and supporting files.
Status in source: current.
Names: delay-Freecooling
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"delay-Freecooling",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"9999",
")",
"UNITS",
[
"literal",
"224e2f4122"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Delay Freecooling\"",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
9999
]
]
]
],
[
"UNITS",
"N/A"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Delay Freecooling"
],
null,
null,
null,
null
]
}Vendor MIB copy from the LibreNMS archive.
Module: KELVIN-pCOWeb-Chiller-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'NOTIFICATION-TYPE', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Related source files and packages:
Same file in Observium Community.
Status in source: current.
Names: intervallo_tra_pulizie
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"intervallo_tra_pulizie",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"1",
".",
".",
"999",
")",
"UNITS",
[
"literal",
"22686f75727322"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Time between two successive cleanings\"",
"DEFVAL",
"{",
"1",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
1,
999
]
]
]
],
[
"UNITS",
"hours"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Time between two successive cleanings"
],
null,
null,
null,
[
"DEFVAL",
1
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-mastercase-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: defrost_t3_hh
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"defrost_t3_hh",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"23",
")",
"UNITS",
[
"literal",
"226f726522"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Defrost event 3 hour\"",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
23
]
]
]
],
[
"UNITS",
"ore"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Defrost event 3 hour"
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-mastercellasplit-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: rit_dif_olio
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"rit_dif_olio",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"360",
")",
"UNITS",
[
"literal",
"2273656322"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Delay in oil differential alarm at start\"",
"DEFVAL",
"{",
"90",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
360
]
]
]
],
[
"UNITS",
"sec"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Delay in oil differential alarm at start"
],
null,
null,
null,
[
"DEFVAL",
90
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-fcp-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: ist_parz2_es
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"ist_parz2_es",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"100",
")",
"UNITS",
[
"literal",
"222522"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Capacity control 2 hysteresis with energy saving\"",
"DEFVAL",
"{",
"100",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
100
]
]
]
],
[
"UNITS",
"%"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Capacity control 2 hysteresis with energy saving"
],
null,
null,
null,
[
"DEFVAL",
100
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-cdz_pco-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: hum-hours-l
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"hum-hours-l",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"-",
"32768",
".",
".",
"32767",
")",
"UNITS",
[
"literal",
"22686f757222"
],
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"Humidifier Runtime - low\"",
"DEFVAL",
"{",
"0",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
-32768,
32767
]
]
]
],
[
"UNITS",
"hour"
],
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Humidifier Runtime - low"
],
null,
null,
null,
[
"DEFVAL",
0
]
]
}Vendor MIB copy from the LibreNMS archive.
Module: DataAire-dap4-al-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Vendor MIB copy from the Observium Community archive.
Module: DataAire-dap4-al-MIB
Same published definition (formatting differs; exact original is in the source file)
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: defrost_t4_mm
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"defrost_t4_mm",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"59",
")",
"UNITS",
[
"literal",
"226d696e22"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Defrost event 4th min\"",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
59
]
]
]
],
[
"UNITS",
"min"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Defrost event 4th min"
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-powersplit-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: f15
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"f15",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"99",
")",
"UNITS",
[
"literal",
"226d696e22"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Air stirring active duration.\"",
"DEFVAL",
"{",
"0",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
99
]
]
]
],
[
"UNITS",
"min"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Air stirring active duration."
],
null,
null,
null,
[
"DEFVAL",
0
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-aria-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: n_partial
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"n_partial",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"3",
")",
"UNITS",
[
"literal",
"224e2f4122"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Number of voltage variations\"",
"DEFVAL",
"{",
"1",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
3
]
]
]
],
[
"UNITS",
"N/A"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Number of voltage variations"
],
null,
null,
null,
[
"DEFVAL",
1
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-insgrd-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: postdef_dr_t_dd
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"postdef_dr_t_dd",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"15",
")",
"UNITS",
[
"literal",
"226d696e22"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"post-defrost dripping time\"",
"DEFVAL",
"{",
"2",
"}",
"::=",
"{",
"integerObjects",
"47",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
15
]
]
]
],
[
"UNITS",
"min"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"post-defrost dripping time"
],
null,
null,
null,
[
"DEFVAL",
2
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-plugin-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Registration
| OID | Name | Direct children | Descendants | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9839.2.1.3.1 | filterWorkH, disch-air-lo-sp, ore-filtro, modello, id_firm_vers, probe_delay, hightempdelay, modo_funz_c0, velocita_vent, unit_status, mod, probe_stability, tipo_sonda__3 | 0 | 0 | Air Filter Working Houres |
| 1.3.6.1.4.1.9839.2.1.3.2 | unitWorkH, humidity-dis, ore-unit, type_defrost, stabilita_misura, virt_probe, defrostdelay, rit_2ins_c6, net_address, sonde, min_in_corr__4 | 0 | 0 | Unit Working Houres |
| 1.3.6.1.4.1.9839.2.1.3.3 | compr1WorkH, stages-on, ore-compr1, filter_digital, sonda_virtuale, defrostprobepresence, ampsignal, tmin_2out_c7, cound_fans_mng, a1, showprobe, max_in_corr__5 | 0 | 0 | Compressor 1 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.4 | compr2WorkH, heaters-on, ore-compr2, derivata, vis_ripetitore, showprobe_t, tmin_off_out_c8, config_type, a2, filtro_dig__b | 0 | 0 | Compressor 2 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.5 | compr3WorkH, minmax-24hr-hum-maximum, ore-compr3, virtual_probe, esiste_sonda, dig_in_term_cfg_1, tmin_on_c9, number_comps, defrostprobepresence, limitaz_in__c | 0 | 0 | Compressor 3 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.6 | compr4WorkH, ip-Address1, minmax-24hr-hum-minumum, ore-compr4, delay_from_startup, vis_terminale, dig_in_term_cfg_2, sicur_sonde, filtro_digitale, cond_fans, dig_in_cfg_1, tmin_on_comp_c1 | 0 | 0 | Compressor 4 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.7 | heat1WorkH, ip-Address2, comp-duty, ore-heat1, interval_between_2_start-up, config_in_digit_1, dig_in_cfg_1, rotazione, a5, dig_in_cfg_2 | 0 | 0 | Heater 1 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.8 | heat2WorkH, ip-Address3, heat-duty, ore-heat2, time_min_off, config_in_digit_2, dig_in_cfg_2, velocita_sonda, tmin_on_comp_c1, modalita_ventole, a6, alarm_input_delay, time_2_acc_c3 | 0 | 0 | Heater 2 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.9 | humiWorkH, ip-Address4, hum-duty, ore-umid, time_min_on, config_in_digit_3, alarm_input_delay, presenza_sonda, tmin_sp_comp_c2, d1, alarm_delay, msrmnt_stab__2 | 0 | 0 | Humidifier Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.10 | c1-hours-h, netMask, safety_relay, n_comp, config_in_digit_4, alarm_delay, tempo_allarme, time_2_acc_c3, cu_remote_ctrl, ore_comp1, in_rampa_p, d2, comp_startup_delay, rit_off_2c_c5, prb_read_spd__3 | 0 | 0 | Compressor 1 Runtime -This point applies to DX unit with one compressor -high |
| 1.3.6.1.4.1.9839.2.1.3.11 | c1-hours-l, gateway1, fan_h_count_fa, duration_cc, n_vent, config_in_digit_5, comp_startup_delay, gestione_id1, rit_on_comp_c6, recover_mode, ore_comp2, fin_rampa_p, comp_s2s_delay, lhour, prb_virtual__4 | 0 | 0 | Compressor 1 Runtime -This point applies to DX unit with one compressor -low |
| 1.3.6.1.4.1.9839.2.1.3.12 | dehumPband, gateway2, c2-hours-h, filt_h_count_fc, hdiff, no_alarm_after_cc, lhour, time_delay_rilevaz_ingresso, comp_s2s_delay, gestione_id2, rit_c_on_pmp_c7, unit_status, in_rampa_n, comp_min_off_time, lminute, unit_msrmnt__5 | 0 | 0 | Dehumidification Prop.Band |
| 1.3.6.1.4.1.9839.2.1.3.13 | humidPband, gateway3, c2-hours-l, cmp1_h_count_c9, hu-diff, interval_between_defrost, lminute, config_virt_din, comp_min_off_time, sicur_all_id, off_p_off_v_c8, cond_fans_mng, fin_rampa_n, d5, comp_min_on_time, lday, off_p_off_c_c8, en_dec_point__6 | 0 | 0 | Humidification Prop.Band |
| 1.3.6.1.4.1.9839.2.1.3.14 | hhAlarmThrsh, gateway4, ht1-hours-h, cmp2_h_count_ca, hh-set, duration_def, hour, delay_alrm_temp, comp_min_on_time, set_gradino1, contaore_c1_c9, d6, rele_safety_cycle, lmonth, ore_comp1_c9, vis_repeater__7 | 0 | 0 | High Humidity Alarm Threshold |
| 1.3.6.1.4.1.9839.2.1.3.15 | lhAlarmThrsh, dns1-1, ht1-hours-l, en_fan_hc_f9, lh-set, delay_def_after_sturt_up, minute, remote_alarms_dsply_enable, rele_safety_cycle, offset_grad1, max_ore_comp_cb, n1, cc_alarm_delay, lyear | 0 | 0 | Low Humidity Alarm Threshold |
| 1.3.6.1.4.1.9839.2.1.3.16 | dehumSetp, dns1-2, current-second, en_filt_hc_fb, hset, dripping_iyme, ora_autocall, gestione_ventole, cc_alarm_delay, diff_gradino1, ore_pmp_vent_cc, set_comp1_cw, r1, comp_cc, hour, def_probe3__9 | 0 | 0 | Dehumidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.17 | smDehumSetp, dns1-3, current-minute, en_cmps_hc_c8, hset-sm, duration_of_alarm, minuti_autocall, ventole_off_se_compr_off, max_pd_time, set_gradino2, modo_vent_f2, ist_comp1_cw, f1, defrost_type, minute, ore_comp2_ca | 0 | 0 | Setback Mode: Dehumidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.18 | humidSetp, dns1-4, current-hour, unit_model_h1, hu-set, rit_all_temp, sg_ore_comp, ventole_stop_in_sbrin, dly_valve_comp, offset_grad2, min_volt_f3, set_comp2_cw, t_on_fan_f1, n2, defrost_delay, month, max_ore_comp_cb, exist_probe__a | 0 | 0 | Humidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.19 | smHumidSetp, dns2-1, current-day, cool_mode_h5, hu-set-sm, config_dig_in1, ore_comp1, time_fermo_post_gocciol, comp_cc, diff_gradino2, max_volt_f4, rit_all_ht_in, ist_comp2_cw, tm_postdripp_fd, r2, alarm_delay_df_door, pyear, ore_pompa_cc | 0 | 0 | Setback Mode: Humidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.20 | pwOnDelay, dns2-2, current-month, heat_mode_h6, restart-delay, config_dig_in2, ore_comp2, address_seriale, defrost_type, set_gradino3, t_spunto_v_fb, x_h_main_pump, rit_all_press, f2, dripping_interval, rit_c_f_cond_cd, set_r1 | 0 | 0 | Restart Delay |
| 1.3.6.1.4.1.9839.2.1.3.21 | regulDelay, dns2-3, current-year, en_humidif_h8, regul-delay, look_comp_ext, ore_comp3, en_dis_tasti_ir, dly_def_gas, offset_grad3, t_imp_triac_fc, x_l_main_pump, s1, setpoint_l1, n3, defrost_interval, oil_diff, modo_fan_f2, set_r2 | 0 | 0 | Regulation Start Transitory |
| 1.3.6.1.4.1.9839.2.1.3.22 | lowPdelay, dns2-4, firestat-sp, tempo_di_escursione_valvola_3, time-lowp, delay_activ_alr, codice_abilit_progr_telec_ir, defrost_delay, diff_gradino3, t_min_on_def_d5, x_h_comp1, s8, set_comp1_es, r3, defrost_max_time, min_volt_f3, en_ed_alarm_r3 | 0 | 0 | Low Pressure Delay |
| 1.3.6.1.4.1.9839.2.1.3.23 | thAlarmdelay, hum-hi-sp, prop_pi_re, alarm-delay, enabling_telecom, loc_on_off_ena, alarm_delay_df_door, set_gradino4, t_min_def_d6, x_l_comp1, n_comp_deum, s6, ist_comp1_es, stability__2, f3, fan_drip_interval, max_volt_f4 | 0 | 0 | Temp./Humid.Limits Alarm Delay |
| 1.3.6.1.4.1.9839.2.1.3.24 | regExcTime, ret-air-hi-sp, pi_time_rf, exc-time, sto_after_drip, lan_on_off_ena, dripping_interval, offset_grad4, t_max_def_d7, x_h_comp2, rit_stop_ventp, s9, set_comp2_es, min_setp_r1, n4, aux1_cfg, t_spunto_f_fb, en_t_maxmin_r5 | 0 | 0 | Anti-Hunting Constant |
| 1.3.6.1.4.1.9839.2.1.3.25 | stdbyTime, hum-lo-sp, conf_humid_h9, t-std-by, key_lock, config_out_digit_4, defrost_interval, diff_gradino4, rit_tra_2def_d8, x_l_comp2, rit_part_comp, s10, ist_comp2_es, max_setp_r2, r4, aux2_cfg, t_min_on_def_d5, reg_n_prb3_r6 | 0 | 0 | Stand-by Cycle Base Time |
| 1.3.6.1.4.1.9839.2.1.3.26 | ret-air-lo-sp, ip-Address1-Out, conf_b2_hc, fan_man_f0, config_out_digit_7, defrost_max_time, tast_telecom, wait_on_def_dc, x_h_comp3, rit_interbl, r19, rit_fra_ins, differ_rd, f4, light_sens_1, out_inv_fani, t_min_def_d6, tm_t_maxmin_rt | 0 | 0 | Lower limit alarm of return air temp |
| 1.3.6.1.4.1.9839.2.1.3.27 | lanUnit, ip-Address2-Out, hum-deadband, conf_b3_hd, lan-unit, oper_mode_h1, local_mode, fan_drip_interval, codice_telecom, wait_end_def_dd, x_l_comp3, min_sp_comp, r20, ngt_setp_var_r4, out, light_timer, inverter_compi1, t_max_def_d7 | 0 | 0 | Number of LAN Units |
| 1.3.6.1.4.1.9839.2.1.3.28 | smCycleTime, ip-Address3-Out, hum-setpoint, conf_anout2_hb, ciclo-sm, lan_len, aux1_cfg, rit_all_ag_a3, x_h_comp4, new_pass_ut, r21, rit_bassa_pres, thr_lt_al_al, mode, minmax_acq_time, board_type, rit_2def_1c_d8 | 0 | 0 | Sleep Mode Testing Cycle Time |
| 1.3.6.1.4.1.9839.2.1.3.29 | exv1steps, ip-Address4-Out, start-dly, id_on_off_he, delay_start_compressore, aux2_cfg, r_al_on_flux_p1, x_l_comp4, h3, rit_riaccen, thr_ht_al_ah, link1, haccp_ha_day, unit_status, rit_def_2c_d9, tm_delay_c0 | 0 | 0 | Circuit 1 EXV Valve Position |
| 1.3.6.1.4.1.9839.2.1.3.30 | exv2steps, starting-delay-Second-Pump, alm1-del, al_out_lgk_hf, time_min_tra_acc_compr, light_sens_1, r_al_rg_flux_p2, config_unit, new_pass_cos, h4, rit_tra_ins, id_al_delay_a7, link2, haccp_ha_hour, type_b1, rit_all_ag_a3, tm_btwn_comp_c1 | 0 | 0 | Circuit 2 EXV Valve Position |
| 1.3.6.1.4.1.9839.2.1.3.31 | alm2-del, starting-delay-btw-Pump-Compressor, conf_deshum_ha, time_min_compr_off, sgl_all_min_rel, rit_all_lp_p3, config_type, min_stes_comp, h5, n_res, conf_id_a4, outl1, haccp_ha_min, type_b2, rall_on_flux_p1, comp_off_tm_c2 | 0 | 0 | Optional Alarm 2 Delay |
| 1.3.6.1.4.1.9839.2.1.3.32 | alm3-del, overlap-time-Pumps, conf_id_al_pb, time_min_compr_on, minmax_acq_time, t_buzzer_p4, ph_circ_type, min_tra_comp, p2, n_comp, comp_delay_c0, outl2, haccp_hf_day, bios_release, rall_rg_flux_p2, comp_on_tm_c3 | 0 | 0 | Optional Alarm 3 Delay |
| 1.3.6.1.4.1.9839.2.1.3.33 | alarm1-txt, working-time-Pumps, un_rot_num_h2, sicurezza_rele, haccp_ha_day, riprist_all_p5, n_comps, min_acc_comp, s7, rit_hl, t_al_delay_ad, priority, haccp_hf_hour, bios_date, rit_all_bp_p3, relay_safety_c4 | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.34 | alarm2-txt, running-time-Chillers, un_rot_adr_h3, time_escl_alrm_dopo_ciclo_cont, haccp_ha_hour, day, selez_id1_p8, comps_x_unit, rit_resistenze, keycode_sv_h5, alcomm, haccp_hf_min, boot_release, buzzer_p4, cnt_cycl_dur_cc | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.35 | alarm3-txt, overlap-time-Chillers, rot_time_h4, delay_start_valve_comp, haccp_ha_min, month, selez_id2_p9, n_unloaders, tempo_max, h18, en_def_mf_h1, dk1, haccp_alarm_delay, boot_date, modello_h1, al_time_excl_c6 | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.36 | alarm4-txt, n-chillers-Max, presenza_sonda_1, durata_ciclo_continuo, haccp_hf_day, pyear, modello_mac_h1, cond_fans, min_apertura, c1, t_betw_2_on_c1, dk2, defrost_t1_dd, modo_pompa_h5, defrost_type_d0 | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.37 | comp-sel, n-chillers-ON, tipo_sonda_2, tipo_sbrinamento, haccp_hf_hour, lday, modo_pmp_vnt_h5, fan1_speed_reg, sgl_macchina, c2, min_off_time_c2, defrost_t1_hh, time_switch_on1, blocca_tasti_h9, tm_btwn_defs_di | 0 | 0 | Comps 0=none, 1=one, 2=one+UL, 3=two, 4=two+UL, 5=Four/two circuit |
| 1.3.6.1.4.1.9839.2.1.3.38 | dehum-mode, n-pumps-ON, presenza_sonda_3, defrost_cmd, haccp_hf_min, lmonth, blocca_tasti_h9, fan2_speed_reg, c3, set_parz1_cw, min_on_time_c3, defrost_t1_mm, time_switchoff1, def_end_time_dt | 0 | 0 | 0=none, 1= comp limited, 2=twocomp limited, 3= comp unlimited, 4=twocomp unlimited |
| 1.3.6.1.4.1.9839.2.1.3.39 | reheat-sel, time-Enable-Pumps-Chiller-Offline, filtro_digitale, threshold_val_comp_run_def, haccp_rit_alarm, lyear, seradd, freecool_valve, c4, ist_parz1_cw, t_safe_relay_c4, dk5, defrost_t2_dd, time_min_on, delay_def_dc | 0 | 0 | Number of heat stages |
| 1.3.6.1.4.1.9839.2.1.3.40 | hum-sel, time-Running-Pumps-Chiller-Offline, limitazione_ingresso, sbrin_se_ast_da_off_ad_on, defrost_t1_dd, hour, passw_telec_hb, c8, set_parz2_cw, cont_cycle_cc, dk6, defrost_t2_hh, time_min_off, time_wait_def_dd, def_max_time_dp | 0 | 0 | 0=none, 1=comp mod, 2=comp non, 3= comf mod, 4= conf non mod |
| 1.3.6.1.4.1.9839.2.1.3.41 | alm-contact-msg, integral-Time-3Way-Valve-Hydraulic-PID, keyb_lockup_hi, delay_sbrin_astoffon_o_digin, defrost_t1_hh, minute, valv_inv_ch_he, n_res, f1, ist_parz2_cw, offal_postcc_c6, defrost_t2_mm, time_betw_comp, valve_status, def_startup_d4 | 0 | 0 | Text displayed on all alarm screens |
| 1.3.6.1.4.1.9839.2.1.3.42 | powerup-sel, derivative-Time-3Way-Valve-Hydraulic-PID, param_set_hl, stop_vis_in_sbrin, defrost_t1_mm, lhour, numero_term_h8, tempo_integra, f2, def_type_d0, defrost_t3_dd, time_same_comp, def_del_su_d5 | 0 | 0 | 0= start wo/alarm, 1= start w/alarm, 2= requires reset of alarm |
| 1.3.6.1.4.1.9839.2.1.3.43 | buzzer-select, output-Address-3Way-Valve-Hydraulic, display_cfg_hn, skip_defrost_enable, defrost_t2_dd, lminute, high_temp_all_pc, f6, t_betw_def_dl, defrost_t3_hh, unload_delay, stop_vis_def_d6 | 0 | 0 | 0=None, 1=short beeps, 2=long beep, 3=Constant |
| 1.3.6.1.4.1.9839.2.1.3.44 | cw-disp, time-Speed-Up-FCM, buzzer_cfg_p4, time_escl_alrm_dopo_sbrin, defrost_t2_hh, delay_low_press, set_parz1_es, def_end_t_dt, defrost_t3_mm, time_switch_on2, drip_tm_def_dd | 0 | 0 | % of 10volts of analog output #1 |
| 1.3.6.1.4.1.9839.2.1.3.45 | wtrvlv-duty, time-Soft-Start-FCM, alm_reset_p5, priority_sbrin_su_protez_compr, defrost_t2_mm, n_devices1, ist_parz1_es, def_durat_dp, defrost_t4_dd, time_switchoff2, aloff_tm_def_d8 | 0 | 0 | Chilled Water Utilization Over Last Hour - This applies to Chilled water or Energy saver units. |
| 1.3.6.1.4.1.9839.2.1.3.46 | hum-hours-h, intervallo_tra_sbrin, defrost_t3_dd, n_devices2, f14, set_parz2_es, def_delay_d5, defrost_t4_hh, time_betw_fan, def_priority_d9 | 0 | 0 | Humidifier Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.48 | blower-hours-h, integral-Time-Freeccoling-PID, user_pw_hh, max_durata_sbrin, defrost_t3_mm, r18, t_int, t_al_exc_def_d8, defrost_t5_dd, rit_all_liq | 0 | 0 | Blower Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.49 | blower-hours-l, derivative-Time-Freeccoling-PID, sw_release_hr, time_gocciol_dopo_sbrin, defrost_t4_dd, r10, diff_al_fan_a0, defrost_t5_hh, time_base_dc | 0 | 0 | Blower Runtime - low |
| 1.3.6.1.4.1.9839.2.1.3.50 | alm4-del, time-Min-On-Freecooling-Chiller-timing, fan_config_f1, intervallo_rilev_temp_maxmin, defrost_t4_hh, r11, sgl_ore_mac, defrost_t5_mm, machine_config | 0 | 0 | Optional Alarm 4 Delay |
| 1.3.6.1.4.1.9839.2.1.3.51 | assist-sel, time-Min-Off-Freecooling-Chiller-timing, min_volt_f2, stn, defrost_t4_mm, versione_sw_hg, f7, sgl_ore_comp1, defrost_t6_dd, swrel | 0 | 0 | 0= no comp assist, 1=one comp assist, 2= two comp assist, 3... 4... |