OID reference
1.3.6.1.4.1.9839.2.1.3.50
Optional Alarm 4 Delay
Identification
{1 3 6 1 4 1 9839 2 1 3 50}
Definitions may combine these properties differently.
At least one MIB declaration places this object in a scalar group. A scalar instance uses the suffix .0.
snmpget [connection options] DEVICE .1.3.6.1.4.1.9839.2.1.3.50.0
Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.
Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.
Available source records contain 9 distinct definitions; some records may not include a definition.
intervallo_rilev_temp_maxmin OBJECT-TYPE
SYNTAX Integer32 (0..999)
UNITS "hours"
MAX-ACCESS read-only
STATUS current
DESCRIPTION "HACCP alarm delay"
DEFVAL { 0 }
::= { integerObjects 50 }r11 OBJECT-TYPE
SYNTAX Integer32 (0..1)
UNITS "N/A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Heating resistors with compressor enable."
DEFVAL { 1 }
::= { integerObjects 50 }alm4-del OBJECT-TYPE
SYNTAX Integer32 (0..32000)
UNITS "N/A"
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Optional Alarm 4 Delay"
DEFVAL { 0 }
::= { integerObjects 50 }fan_config_f1 OBJECT-TYPE
SYNTAX Integer32 (0..2)
UNITS "flag"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Fan operating mode"
DEFVAL { 1 }
::= { integerObjects 50 }defrost_t5_mm OBJECT-TYPE
SYNTAX Integer32 (0..59)
UNITS "min"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Defrost event 5 min"
::= { integerObjects 50 }machine_config OBJECT-TYPE
SYNTAX Integer32 (-32767..32767)
UNITS "N/A"
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Machine configuration"
::= { integerObjects 50 }sgl_ore_mac OBJECT-TYPE
SYNTAX Integer32 (0..999)
UNITS "sec"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Fan operation time limit"
DEFVAL { 200 }
::= { integerObjects 50 }defrost_t4_hh OBJECT-TYPE
SYNTAX Integer32 (0..23)
UNITS "ore"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Defrost event 4 hour"
::= { integerObjects 50 }time-Min-On-Freecooling-Chiller-timing OBJECT-TYPE
SYNTAX Integer32 (0..32767)
UNITS "N/A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Time Min. On (Freecooling - Chiller timing)"
::= { integerObjects 50 }
Meaning
Identical descriptions are grouped. Different wording and device-specific notes are retained.
Description 1
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 2
HACCP alarm delay
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 3
Heating resistors with compressor enable.
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 4
Fan operating mode
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 5
Defrost event 5 min
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 6
Machine configuration
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 7
Fan operation time limit
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 8
Defrost event 4 hour
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Description 9
Time Min. On (Freecooling - Chiller timing)
Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
Evidence
Matching descriptions are grouped; open a group to compare definitions and supporting files.
Status in source: current.
Names: intervallo_rilev_temp_maxmin
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"intervallo_rilev_temp_maxmin",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"999",
")",
"UNITS",
[
"literal",
"22686f75727322"
],
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"HACCP alarm delay\"",
"DEFVAL",
"{",
"0",
"}",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
999
]
]
]
],
[
"UNITS",
"hours"
],
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"HACCP alarm delay"
],
null,
null,
null,
[
"DEFVAL",
0
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-mastercase-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Related source files and packages:
Status in source: current.
Names: r11
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"r11",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"1",
")",
"UNITS",
[
"literal",
"224e2f4122"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Heating resistors with compressor enable.\"",
"DEFVAL",
"{",
"1",
"}",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
1
]
]
]
],
[
"UNITS",
"N/A"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Heating resistors with compressor enable."
],
null,
null,
null,
[
"DEFVAL",
1
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-aria-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: alm4-del
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"alm4-del",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"32000",
")",
"UNITS",
[
"literal",
"224e2f4122"
],
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"Optional Alarm 4 Delay\"",
"DEFVAL",
"{",
"0",
"}",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
32000
]
]
]
],
[
"UNITS",
"N/A"
],
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Optional Alarm 4 Delay"
],
null,
null,
null,
[
"DEFVAL",
0
]
]
}Vendor MIB copy from the LibreNMS archive.
Module: DataAire-dap4-al-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Related source files and packages:
Vendor MIB copy from the Observium Community archive.
Module: DataAire-dap4-al-MIB
Same published definition (formatting differs; exact original is in the source file)
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: fan_config_f1
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"fan_config_f1",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"2",
")",
"UNITS",
[
"literal",
"22666c616722"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Fan operating mode\"",
"DEFVAL",
"{",
"1",
"}",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
2
]
]
]
],
[
"UNITS",
"flag"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Fan operating mode"
],
null,
null,
null,
[
"DEFVAL",
1
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-uac-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: defrost_t5_mm
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"defrost_t5_mm",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"59",
")",
"UNITS",
[
"literal",
"226d696e22"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Defrost event 5 min\"",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
59
]
]
]
],
[
"UNITS",
"min"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Defrost event 5 min"
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-powersplit-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: machine_config
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"machine_config",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"-",
"32767",
".",
".",
"32767",
")",
"UNITS",
[
"literal",
"224e2f4122"
],
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"Machine configuration\"",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
-32767,
32767
]
]
]
],
[
"UNITS",
"N/A"
],
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Machine configuration"
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-uchiller-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: sgl_ore_mac
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"sgl_ore_mac",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"999",
")",
"UNITS",
[
"literal",
"2273656322"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Fan operation time limit\"",
"DEFVAL",
"{",
"200",
"}",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
999
]
]
]
],
[
"UNITS",
"sec"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Fan operation time limit"
],
null,
null,
null,
[
"DEFVAL",
200
]
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-cdz_pco-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: defrost_t4_hh
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"defrost_t4_hh",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"23",
")",
"UNITS",
[
"literal",
"226f726522"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Defrost event 4 hour\"",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
23
]
]
]
],
[
"UNITS",
"ore"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Defrost event 4 hour"
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive.
Module: CAREL-mastercellasplit-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Status in source: current.
Names: time-Min-On-Freecooling-Chiller-timing
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"time-Min-On-Freecooling-Chiller-timing",
"OBJECT-TYPE",
"SYNTAX",
"Integer32",
"(",
"0",
".",
".",
"32767",
")",
"UNITS",
[
"literal",
"224e2f4122"
],
"MAX-ACCESS",
"read-write",
"STATUS",
"current",
"DESCRIPTION",
"\"Time Min. On (Freecooling - Chiller timing)\"",
"::=",
"{",
"integerObjects",
"50",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"Integer32",
[
"integerSubType",
[
[
0,
32767
]
]
]
],
[
"UNITS",
"N/A"
],
[
"MaxAccessPart",
"read-write"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"Time Min. On (Freecooling - Chiller timing)"
],
null,
null,
null,
null
]
}Vendor MIB copy from the LibreNMS archive.
Module: KELVIN-pCOWeb-Chiller-MIB
See published definition above
{'SNMPv2-MIB': ['sysContact', 'sysName', 'sysLocation'], 'SNMPv2-SMI': ['enterprises', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'NOTIFICATION-TYPE', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP']}Same file in Observium Community.
Registration
| OID | Name | Direct children | Descendants | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9839.2.1.3.1 | filterWorkH, disch-air-lo-sp, ore-filtro, modello, id_firm_vers, probe_delay, hightempdelay, modo_funz_c0, velocita_vent, unit_status, mod, probe_stability, tipo_sonda__3 | 0 | 0 | Air Filter Working Houres |
| 1.3.6.1.4.1.9839.2.1.3.2 | unitWorkH, humidity-dis, ore-unit, type_defrost, stabilita_misura, virt_probe, defrostdelay, rit_2ins_c6, net_address, sonde, min_in_corr__4 | 0 | 0 | Unit Working Houres |
| 1.3.6.1.4.1.9839.2.1.3.3 | compr1WorkH, stages-on, ore-compr1, filter_digital, sonda_virtuale, defrostprobepresence, ampsignal, tmin_2out_c7, cound_fans_mng, a1, showprobe, max_in_corr__5 | 0 | 0 | Compressor 1 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.4 | compr2WorkH, heaters-on, ore-compr2, derivata, vis_ripetitore, showprobe_t, tmin_off_out_c8, config_type, a2, filtro_dig__b | 0 | 0 | Compressor 2 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.5 | compr3WorkH, minmax-24hr-hum-maximum, ore-compr3, virtual_probe, esiste_sonda, dig_in_term_cfg_1, tmin_on_c9, number_comps, defrostprobepresence, limitaz_in__c | 0 | 0 | Compressor 3 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.6 | compr4WorkH, ip-Address1, minmax-24hr-hum-minumum, ore-compr4, delay_from_startup, vis_terminale, dig_in_term_cfg_2, sicur_sonde, filtro_digitale, cond_fans, dig_in_cfg_1, tmin_on_comp_c1 | 0 | 0 | Compressor 4 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.7 | heat1WorkH, ip-Address2, comp-duty, ore-heat1, interval_between_2_start-up, config_in_digit_1, dig_in_cfg_1, rotazione, a5, dig_in_cfg_2 | 0 | 0 | Heater 1 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.8 | heat2WorkH, ip-Address3, heat-duty, ore-heat2, time_min_off, config_in_digit_2, dig_in_cfg_2, velocita_sonda, tmin_on_comp_c1, modalita_ventole, a6, alarm_input_delay, time_2_acc_c3 | 0 | 0 | Heater 2 Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.9 | humiWorkH, ip-Address4, hum-duty, ore-umid, time_min_on, config_in_digit_3, alarm_input_delay, presenza_sonda, tmin_sp_comp_c2, d1, alarm_delay, msrmnt_stab__2 | 0 | 0 | Humidifier Run Hours |
| 1.3.6.1.4.1.9839.2.1.3.10 | c1-hours-h, netMask, safety_relay, n_comp, config_in_digit_4, alarm_delay, tempo_allarme, time_2_acc_c3, cu_remote_ctrl, ore_comp1, in_rampa_p, d2, comp_startup_delay, rit_off_2c_c5, prb_read_spd__3 | 0 | 0 | Compressor 1 Runtime -This point applies to DX unit with one compressor -high |
| 1.3.6.1.4.1.9839.2.1.3.11 | c1-hours-l, gateway1, fan_h_count_fa, duration_cc, n_vent, config_in_digit_5, comp_startup_delay, gestione_id1, rit_on_comp_c6, recover_mode, ore_comp2, fin_rampa_p, comp_s2s_delay, lhour, prb_virtual__4 | 0 | 0 | Compressor 1 Runtime -This point applies to DX unit with one compressor -low |
| 1.3.6.1.4.1.9839.2.1.3.12 | dehumPband, gateway2, c2-hours-h, filt_h_count_fc, hdiff, no_alarm_after_cc, lhour, time_delay_rilevaz_ingresso, comp_s2s_delay, gestione_id2, rit_c_on_pmp_c7, unit_status, in_rampa_n, comp_min_off_time, lminute, unit_msrmnt__5 | 0 | 0 | Dehumidification Prop.Band |
| 1.3.6.1.4.1.9839.2.1.3.13 | humidPband, gateway3, c2-hours-l, cmp1_h_count_c9, hu-diff, interval_between_defrost, lminute, config_virt_din, comp_min_off_time, sicur_all_id, off_p_off_v_c8, cond_fans_mng, fin_rampa_n, d5, comp_min_on_time, lday, off_p_off_c_c8, en_dec_point__6 | 0 | 0 | Humidification Prop.Band |
| 1.3.6.1.4.1.9839.2.1.3.14 | hhAlarmThrsh, gateway4, ht1-hours-h, cmp2_h_count_ca, hh-set, duration_def, hour, delay_alrm_temp, comp_min_on_time, set_gradino1, contaore_c1_c9, d6, rele_safety_cycle, lmonth, ore_comp1_c9, vis_repeater__7 | 0 | 0 | High Humidity Alarm Threshold |
| 1.3.6.1.4.1.9839.2.1.3.15 | lhAlarmThrsh, dns1-1, ht1-hours-l, en_fan_hc_f9, lh-set, delay_def_after_sturt_up, minute, remote_alarms_dsply_enable, rele_safety_cycle, offset_grad1, max_ore_comp_cb, n1, cc_alarm_delay, lyear | 0 | 0 | Low Humidity Alarm Threshold |
| 1.3.6.1.4.1.9839.2.1.3.16 | dehumSetp, dns1-2, current-second, en_filt_hc_fb, hset, dripping_iyme, ora_autocall, gestione_ventole, cc_alarm_delay, diff_gradino1, ore_pmp_vent_cc, set_comp1_cw, r1, comp_cc, hour, def_probe3__9 | 0 | 0 | Dehumidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.17 | smDehumSetp, dns1-3, current-minute, en_cmps_hc_c8, hset-sm, duration_of_alarm, minuti_autocall, ventole_off_se_compr_off, max_pd_time, set_gradino2, modo_vent_f2, ist_comp1_cw, f1, defrost_type, minute, ore_comp2_ca | 0 | 0 | Setback Mode: Dehumidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.18 | humidSetp, dns1-4, current-hour, unit_model_h1, hu-set, rit_all_temp, sg_ore_comp, ventole_stop_in_sbrin, dly_valve_comp, offset_grad2, min_volt_f3, set_comp2_cw, t_on_fan_f1, n2, defrost_delay, month, max_ore_comp_cb, exist_probe__a | 0 | 0 | Humidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.19 | smHumidSetp, dns2-1, current-day, cool_mode_h5, hu-set-sm, config_dig_in1, ore_comp1, time_fermo_post_gocciol, comp_cc, diff_gradino2, max_volt_f4, rit_all_ht_in, ist_comp2_cw, tm_postdripp_fd, r2, alarm_delay_df_door, pyear, ore_pompa_cc | 0 | 0 | Setback Mode: Humidification Setpoint |
| 1.3.6.1.4.1.9839.2.1.3.20 | pwOnDelay, dns2-2, current-month, heat_mode_h6, restart-delay, config_dig_in2, ore_comp2, address_seriale, defrost_type, set_gradino3, t_spunto_v_fb, x_h_main_pump, rit_all_press, f2, dripping_interval, rit_c_f_cond_cd, set_r1 | 0 | 0 | Restart Delay |
| 1.3.6.1.4.1.9839.2.1.3.21 | regulDelay, dns2-3, current-year, en_humidif_h8, regul-delay, look_comp_ext, ore_comp3, en_dis_tasti_ir, dly_def_gas, offset_grad3, t_imp_triac_fc, x_l_main_pump, s1, setpoint_l1, n3, defrost_interval, oil_diff, modo_fan_f2, set_r2 | 0 | 0 | Regulation Start Transitory |
| 1.3.6.1.4.1.9839.2.1.3.22 | lowPdelay, dns2-4, firestat-sp, tempo_di_escursione_valvola_3, time-lowp, delay_activ_alr, codice_abilit_progr_telec_ir, defrost_delay, diff_gradino3, t_min_on_def_d5, x_h_comp1, s8, set_comp1_es, r3, defrost_max_time, min_volt_f3, en_ed_alarm_r3 | 0 | 0 | Low Pressure Delay |
| 1.3.6.1.4.1.9839.2.1.3.23 | thAlarmdelay, hum-hi-sp, prop_pi_re, alarm-delay, enabling_telecom, loc_on_off_ena, alarm_delay_df_door, set_gradino4, t_min_def_d6, x_l_comp1, n_comp_deum, s6, ist_comp1_es, stability__2, f3, fan_drip_interval, max_volt_f4 | 0 | 0 | Temp./Humid.Limits Alarm Delay |
| 1.3.6.1.4.1.9839.2.1.3.24 | regExcTime, ret-air-hi-sp, pi_time_rf, exc-time, sto_after_drip, lan_on_off_ena, dripping_interval, offset_grad4, t_max_def_d7, x_h_comp2, rit_stop_ventp, s9, set_comp2_es, min_setp_r1, n4, aux1_cfg, t_spunto_f_fb, en_t_maxmin_r5 | 0 | 0 | Anti-Hunting Constant |
| 1.3.6.1.4.1.9839.2.1.3.25 | stdbyTime, hum-lo-sp, conf_humid_h9, t-std-by, key_lock, config_out_digit_4, defrost_interval, diff_gradino4, rit_tra_2def_d8, x_l_comp2, rit_part_comp, s10, ist_comp2_es, max_setp_r2, r4, aux2_cfg, t_min_on_def_d5, reg_n_prb3_r6 | 0 | 0 | Stand-by Cycle Base Time |
| 1.3.6.1.4.1.9839.2.1.3.26 | ret-air-lo-sp, ip-Address1-Out, conf_b2_hc, fan_man_f0, config_out_digit_7, defrost_max_time, tast_telecom, wait_on_def_dc, x_h_comp3, rit_interbl, r19, rit_fra_ins, differ_rd, f4, light_sens_1, out_inv_fani, t_min_def_d6, tm_t_maxmin_rt | 0 | 0 | Lower limit alarm of return air temp |
| 1.3.6.1.4.1.9839.2.1.3.27 | lanUnit, ip-Address2-Out, hum-deadband, conf_b3_hd, lan-unit, oper_mode_h1, local_mode, fan_drip_interval, codice_telecom, wait_end_def_dd, x_l_comp3, min_sp_comp, r20, ngt_setp_var_r4, out, light_timer, inverter_compi1, t_max_def_d7 | 0 | 0 | Number of LAN Units |
| 1.3.6.1.4.1.9839.2.1.3.28 | smCycleTime, ip-Address3-Out, hum-setpoint, conf_anout2_hb, ciclo-sm, lan_len, aux1_cfg, rit_all_ag_a3, x_h_comp4, new_pass_ut, r21, rit_bassa_pres, thr_lt_al_al, mode, minmax_acq_time, board_type, rit_2def_1c_d8 | 0 | 0 | Sleep Mode Testing Cycle Time |
| 1.3.6.1.4.1.9839.2.1.3.29 | exv1steps, ip-Address4-Out, start-dly, id_on_off_he, delay_start_compressore, aux2_cfg, r_al_on_flux_p1, x_l_comp4, h3, rit_riaccen, thr_ht_al_ah, link1, haccp_ha_day, unit_status, rit_def_2c_d9, tm_delay_c0 | 0 | 0 | Circuit 1 EXV Valve Position |
| 1.3.6.1.4.1.9839.2.1.3.30 | exv2steps, starting-delay-Second-Pump, alm1-del, al_out_lgk_hf, time_min_tra_acc_compr, light_sens_1, r_al_rg_flux_p2, config_unit, new_pass_cos, h4, rit_tra_ins, id_al_delay_a7, link2, haccp_ha_hour, type_b1, rit_all_ag_a3, tm_btwn_comp_c1 | 0 | 0 | Circuit 2 EXV Valve Position |
| 1.3.6.1.4.1.9839.2.1.3.31 | alm2-del, starting-delay-btw-Pump-Compressor, conf_deshum_ha, time_min_compr_off, sgl_all_min_rel, rit_all_lp_p3, config_type, min_stes_comp, h5, n_res, conf_id_a4, outl1, haccp_ha_min, type_b2, rall_on_flux_p1, comp_off_tm_c2 | 0 | 0 | Optional Alarm 2 Delay |
| 1.3.6.1.4.1.9839.2.1.3.32 | alm3-del, overlap-time-Pumps, conf_id_al_pb, time_min_compr_on, minmax_acq_time, t_buzzer_p4, ph_circ_type, min_tra_comp, p2, n_comp, comp_delay_c0, outl2, haccp_hf_day, bios_release, rall_rg_flux_p2, comp_on_tm_c3 | 0 | 0 | Optional Alarm 3 Delay |
| 1.3.6.1.4.1.9839.2.1.3.33 | alarm1-txt, working-time-Pumps, un_rot_num_h2, sicurezza_rele, haccp_ha_day, riprist_all_p5, n_comps, min_acc_comp, s7, rit_hl, t_al_delay_ad, priority, haccp_hf_hour, bios_date, rit_all_bp_p3, relay_safety_c4 | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.34 | alarm2-txt, running-time-Chillers, un_rot_adr_h3, time_escl_alrm_dopo_ciclo_cont, haccp_ha_hour, day, selez_id1_p8, comps_x_unit, rit_resistenze, keycode_sv_h5, alcomm, haccp_hf_min, boot_release, buzzer_p4, cnt_cycl_dur_cc | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.35 | alarm3-txt, overlap-time-Chillers, rot_time_h4, delay_start_valve_comp, haccp_ha_min, month, selez_id2_p9, n_unloaders, tempo_max, h18, en_def_mf_h1, dk1, haccp_alarm_delay, boot_date, modello_h1, al_time_excl_c6 | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.36 | alarm4-txt, n-chillers-Max, presenza_sonda_1, durata_ciclo_continuo, haccp_hf_day, pyear, modello_mac_h1, cond_fans, min_apertura, c1, t_betw_2_on_c1, dk2, defrost_t1_dd, modo_pompa_h5, defrost_type_d0 | 0 | 0 | Message on optional alarm screen, some also add function |
| 1.3.6.1.4.1.9839.2.1.3.37 | comp-sel, n-chillers-ON, tipo_sonda_2, tipo_sbrinamento, haccp_hf_hour, lday, modo_pmp_vnt_h5, fan1_speed_reg, sgl_macchina, c2, min_off_time_c2, defrost_t1_hh, time_switch_on1, blocca_tasti_h9, tm_btwn_defs_di | 0 | 0 | Comps 0=none, 1=one, 2=one+UL, 3=two, 4=two+UL, 5=Four/two circuit |
| 1.3.6.1.4.1.9839.2.1.3.38 | dehum-mode, n-pumps-ON, presenza_sonda_3, defrost_cmd, haccp_hf_min, lmonth, blocca_tasti_h9, fan2_speed_reg, c3, set_parz1_cw, min_on_time_c3, defrost_t1_mm, time_switchoff1, def_end_time_dt | 0 | 0 | 0=none, 1= comp limited, 2=twocomp limited, 3= comp unlimited, 4=twocomp unlimited |
| 1.3.6.1.4.1.9839.2.1.3.39 | reheat-sel, time-Enable-Pumps-Chiller-Offline, filtro_digitale, threshold_val_comp_run_def, haccp_rit_alarm, lyear, seradd, freecool_valve, c4, ist_parz1_cw, t_safe_relay_c4, dk5, defrost_t2_dd, time_min_on, delay_def_dc | 0 | 0 | Number of heat stages |
| 1.3.6.1.4.1.9839.2.1.3.40 | hum-sel, time-Running-Pumps-Chiller-Offline, limitazione_ingresso, sbrin_se_ast_da_off_ad_on, defrost_t1_dd, hour, passw_telec_hb, c8, set_parz2_cw, cont_cycle_cc, dk6, defrost_t2_hh, time_min_off, time_wait_def_dd, def_max_time_dp | 0 | 0 | 0=none, 1=comp mod, 2=comp non, 3= comf mod, 4= conf non mod |
| 1.3.6.1.4.1.9839.2.1.3.41 | alm-contact-msg, integral-Time-3Way-Valve-Hydraulic-PID, keyb_lockup_hi, delay_sbrin_astoffon_o_digin, defrost_t1_hh, minute, valv_inv_ch_he, n_res, f1, ist_parz2_cw, offal_postcc_c6, defrost_t2_mm, time_betw_comp, valve_status, def_startup_d4 | 0 | 0 | Text displayed on all alarm screens |
| 1.3.6.1.4.1.9839.2.1.3.42 | powerup-sel, derivative-Time-3Way-Valve-Hydraulic-PID, param_set_hl, stop_vis_in_sbrin, defrost_t1_mm, lhour, numero_term_h8, tempo_integra, f2, def_type_d0, defrost_t3_dd, time_same_comp, def_del_su_d5 | 0 | 0 | 0= start wo/alarm, 1= start w/alarm, 2= requires reset of alarm |
| 1.3.6.1.4.1.9839.2.1.3.43 | buzzer-select, output-Address-3Way-Valve-Hydraulic, display_cfg_hn, skip_defrost_enable, defrost_t2_dd, lminute, high_temp_all_pc, f6, t_betw_def_dl, defrost_t3_hh, unload_delay, stop_vis_def_d6 | 0 | 0 | 0=None, 1=short beeps, 2=long beep, 3=Constant |
| 1.3.6.1.4.1.9839.2.1.3.44 | cw-disp, time-Speed-Up-FCM, buzzer_cfg_p4, time_escl_alrm_dopo_sbrin, defrost_t2_hh, delay_low_press, set_parz1_es, def_end_t_dt, defrost_t3_mm, time_switch_on2, drip_tm_def_dd | 0 | 0 | % of 10volts of analog output #1 |
| 1.3.6.1.4.1.9839.2.1.3.45 | wtrvlv-duty, time-Soft-Start-FCM, alm_reset_p5, priority_sbrin_su_protez_compr, defrost_t2_mm, n_devices1, ist_parz1_es, def_durat_dp, defrost_t4_dd, time_switchoff2, aloff_tm_def_d8 | 0 | 0 | Chilled Water Utilization Over Last Hour - This applies to Chilled water or Energy saver units. |
| 1.3.6.1.4.1.9839.2.1.3.46 | hum-hours-h, intervallo_tra_sbrin, defrost_t3_dd, n_devices2, f14, set_parz2_es, def_delay_d5, defrost_t4_hh, time_betw_fan, def_priority_d9 | 0 | 0 | Humidifier Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.47 | hum-hours-l, delay-Freecooling, intervallo_tra_pulizie, defrost_t3_hh, n_partial, f15, ist_parz2_es, postdef_dr_t_dd, defrost_t4_mm, rit_dif_olio | 0 | 0 | Humidifier Runtime - low |
| 1.3.6.1.4.1.9839.2.1.3.48 | blower-hours-h, integral-Time-Freeccoling-PID, user_pw_hh, max_durata_sbrin, defrost_t3_mm, r18, t_int, t_al_exc_def_d8, defrost_t5_dd, rit_all_liq | 0 | 0 | Blower Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.49 | blower-hours-l, derivative-Time-Freeccoling-PID, sw_release_hr, time_gocciol_dopo_sbrin, defrost_t4_dd, r10, diff_al_fan_a0, defrost_t5_hh, time_base_dc | 0 | 0 | Blower Runtime - low |
| 1.3.6.1.4.1.9839.2.1.3.51 | assist-sel, time-Min-Off-Freecooling-Chiller-timing, min_volt_f2, stn, defrost_t4_mm, versione_sw_hg, f7, sgl_ore_comp1, defrost_t6_dd, swrel | 0 | 0 | 0= no comp assist, 1=one comp assist, 2= two comp assist, 3... 4... |