This attribute indicates the bearer capability for this connection.
Class a service is a connection-oriented, constant bit rate ATM
transport service. Class a service has end to end timing
requirements and may require stringent cell loss, cell delay and cell
delay variation performance.When a is displayed, the user is
requesting more than an ATM only service. The network may look
at the AAL to provide interworking based upon its contents.
Class c service is a connection-oriented, variable bit rate ATM
transport service. Class c service has no end-to-end timing
requirements.When c is displayed, the user is requesting more than
an ATM only service. The network interworking function may look
at the AAL and provide service based on it.
Class x service is a connection-oriented ATM transport service
where the AAL, trafficType (cbr or vbr), and timing requirements
are user defined (that is, transparent to the network). When the
value of this attribute is x, the user is requesting an ATM only
service from the network. In this case, the network shall not process
any higher layer protocol.
Class vp service is used to indicate a transparent VP service when
the user is requesting an ATM only service from the network. In this
case, the network does not process any higher layer protocol. This
service differs from class x service in that with the class vp service
both the VCI field (except for VCI values 0, 3, 4, and 6 through 15)
and Payload Type field are transported transparently by the network.
This attribute value is only applicable to SPVP and SVP
connections.
A value of notApplicable is displayed in the case of nailed-up PVCs
for which this attribute has no significance.
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute indicates the bearer capability for this connection.
Class a service is a connection-oriented, constant bit rate ATM
transport service. Class a service has end to end timing
requirements and may require stringent cell loss, cell delay and cell
delay variation performance.When a is displayed, the user is
requesting more than an ATM only service. The network may look
at the AAL to provide interworking based upon its contents.
Class c service is a connection-oriented, variable bit rate ATM
transport service. Class c service has no end-to-end timing
requirements.When c is displayed, the user is requesting more than
an ATM only service. The network interworking function may look
at the AAL and provide service based on it.
Class x service is a connection-oriented ATM transport service
where the AAL, trafficType (cbr or vbr), and timing requirements
are user defined (that is, transparent to the network). When the
value of this attribute is x, the user is requesting an ATM only
service from the network. In this case, the network shall not process
any higher layer protocol.
Class vp service is used to indicate a transparent VP service when
the user is requesting an ATM only service from the network. In this
case, the network does not process any higher layer protocol. This
service differs from class x service in that with the class vp service
both the VCI field (except for VCI values 0, 3, 4, and 6 through 15)
and Payload Type field are transported transparently by the network.
This attribute value is only applicable to SPVP and SVP
connections.
A value of notApplicable is displayed in the case of nailed-up PVCs
for which this attribute has no significance.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfVpcTmBearerClassBbc OBJECT-TYPE SYNTAX INTEGER { a(1), c(3), x(16), vp(24), notApplicable(30) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the bearer capability for this connection. Class a service is a connection-oriented, constant bit rate ATM transport service. Class a service has end to end timing requirements and may require stringent cell loss, cell delay and cell delay variation performance.When a is displayed, the user is requesting more than an ATM only service. The network may look at the AAL to provide interworking based upon its contents. Class c service is a connection-oriented, variable bit rate ATM transport service. Class c service has no end-to-end timing requirements.When c is displayed, the user is requesting more than an ATM only service. The network interworking function may look at the AAL and provide service based on it. Class x service is a connection-oriented ATM transport service where the AAL, trafficType (cbr or vbr), and timing requirements are user defined (that is, transparent to the network). When the value of this attribute is x, the user is requesting an ATM only service from the network. In this case, the network shall not process any higher layer protocol. Class vp service is used to indicate a transparent VP service when the user is requesting an ATM only service from the network. In this case, the network does not process any higher layer protocol. This service differs from class x service in that with the class vp service both the VCI field (except for VCI values 0, 3, 4, and 6 through 15) and Payload Type field are transported transparently by the network. This attribute value is only applicable to SPVP and SVP connections. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance." ::= { atmIfVpcTmOperEntry 71 }
atmIfVpcTmBearerClassBbc OBJECT-TYPE SYNTAX INTEGER { a(1), c(3), x(16), vp(24), notApplicable(30) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the bearer capability for this connection. Class a service is a connection-oriented, constant bit rate ATM transport service. Class a service has end to end timing requirements and may require stringent cell loss, cell delay and cell delay variation performance.When a is displayed, the user is requesting more than an ATM only service. The network may look at the AAL to provide interworking based upon its contents. Class c service is a connection-oriented, variable bit rate ATM transport service. Class c service has no end-to-end timing requirements.When c is displayed, the user is requesting more than an ATM only service. The network interworking function may look at the AAL and provide service based on it. Class x service is a connection-oriented ATM transport service where the AAL, trafficType (cbr or vbr), and timing requirements are user defined (that is, transparent to the network). When the value of this attribute is x, the user is requesting an ATM only service from the network. In this case, the network shall not process any higher layer protocol. Class vp service is used to indicate a transparent VP service when the user is requesting an ATM only service from the network. In this case, the network does not process any higher layer protocol. This service differs from class x service in that with the class vp service both the VCI field (except for VCI values 0, 3, 4, and 6 through 15) and Payload Type field are transported transparently by the network. This attribute value is only applicable to SPVP and SVP connections. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance." ::= { atmIfVpcTmOperEntry 71 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.10 | atmIfVpcTmTxTrafficDescType | 0 | 0 | T his attribute indicates the type of traffic management which is applied to the transmit direction of this connection as define… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.31 | atmIfVpcTmTxQosClass | 0 | 0 | This attribute indicates the quality of service for the calling to called direction for this connection. This is only applicable… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.32 | atmIfVpcTmTxQueueLength | 0 | 0 | This attribute indicates the current number of cells in the transmit queue for this connection. If this connection has unshapedT… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.33 | atmIfVpcTmTxQueueCongestionState | 0 | 0 | This attribute indicates the congestion state of the transmit queue for this connection. If this connection has unshapedTransmit… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.35 | atmIfVpcTmHoldingPriority | 0 | 0 | This attribute indicates the actual holding priority in effect for this connection. In a situation where the link bandwidth fluc… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.40 | atmIfVpcTmRxTrafficDescType | 0 | 0 | This attribute indicates the type of traffic management which is applied to the receive direction of this connection as defined … |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.61 | atmIfVpcTmRxQosClass | 0 | 0 | This attribute indicates the quality of service for the called to calling direction for this connection. This is only applicable… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.62 | atmIfVpcTmAtmServiceCategory | 0 | 0 | This attribute indicates the ATM service category used for traffic in both directions of the connection. This attribute does not… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.70 | atmIfVpcTmTrafficShaping | 0 | 0 | This attribute indicates the traffic shaping state of the connection. A value of notApplicable indicates that traffic shaping i… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.72 | atmIfVpcTmTransferCapabilityBbc | 0 | 0 | This attribute indicates the transfer capability for this connection. Uni 3.0/3.1 traffic type and end-to-end timing parameters … |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.74 | atmIfVpcTmClippingBbc | 0 | 0 | This attribute indicates the value of the clipping susceptibility parameter in the broadband bearer capability (BBC) Information… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.75 | atmIfVpcTmUnshapedTransmitQueueing | 0 | 0 | This attribute indicates the unshaped transmit queuing state of the connection. A value of common indicates that transmit traffi… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.76 | atmIfVpcTmBestEffort | 0 | 0 | This attribute indicates value of best effort parameter in the ATM Traffic Descriptor Information Element. The value indicated i… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.78 | atmIfVpcTmForceTagging | 0 | 0 | This attribute indicates the state of force tagging option for this connection. Force tagging refers to setting the CLP bit for … |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.79 | atmIfVpcTmWeight | 0 | 0 | This attribute indicates the relative weight of this unshaped connection. Connections with a larger weight get a larger proporti… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.80 | atmIfVpcTmUsageParameterControl | 0 | 0 | This attribute indicates the UPC state of the connection. A value of notApplicable indicates that UPC is not applicable or not s… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.85 | atmIfVpcTmTxPacketWiseDiscard | 0 | 0 | This attribute indicates the current set of packet-wise discard functions in effect in the transmit data direction at this conne… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.86 | atmIfVpcTmRxPacketWiseDiscard | 0 | 0 | This attribute indicates the current set of packet-wise discard functions in effect in the receive data direction at this connec… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.90 | atmIfVpcTmBandwidthElastic | 0 | 0 | This attribute is only of importance for connections which are carried on a link with a variable bandwidth. For example, the band… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.100 | atmIfVpcTmBandwidthReduction | 0 | 0 | This attribute shows the amount by which the bandwidth has been reduced for this connection. This value is non-zero only for conn… |
1.3.6.1.4.1.562.2.4.1.114.4.9.100.1.110 | atmIfVpcTmAbrConnectionType | 0 | 0 | This attribute indicates the type of ABR behavior which is in effect at this connection. This attribute is only applicable if th… |