The MIB for managing Signalling Points and its
associated messages transported over Signalling
System No. 7 (SS7) Network via Cisco IP Transfer
Point. This MIB replaces the CISCO-ITP-SP-MIB and
provide support multiple instances of a signalling
point within same configuration.
The Cisco IP Transfer Point (ITP) is a hardware
and software solution that transports SS7 traffic
using IP. Each ITP node provides function similar
to SS7 Signalling point.
The relevant ITU documents describing this technology
is the ITU Q series, including ITU Q.700: Introduction
to CCITT Signalling System No. 7 and ITU Q.701
Functional description of the message transfer part
(MTP) of Signalling System No. 7.
This MIB models the GSP as follows:
Abbreviations:
AERM - Alignment Error Rate Monitor
CLLI - Common-Language Location Identification
DPC - Destination Point Code
GSP - Gateway Signalling Point
HSL - High Speed Link (ATM based)
LLSC - link set control
LSAC - Signalling link activity control
LSDA - Signalling data link allocation
LSLA - Signalling link activation
LSLD - Signalling link deactivation
LSLR - Signalling link restoration
LSSU - Link Status Signal Unit
LSTA - Signalling terminal allocation
MTP - Message Transport Protocol
MTP2 - Layer 2 of Message Transport Protocol
MTP3 - Layer 3 of Message Transport Protocol
NTT - The Japanese Nippon Telephone & Telegraph
OPC - Originating Point Code
PC - Point Code
RTN - RouteTableName
SCTP - Stream Transmission Protocol(RFC 2960)
SIB - Status Indicator Busy
SLT - Signalling Link Test
SLTA - Signalling Link Test Acknowledgement
SP - Signalling Point
SS7 - System No. 7 (SS7) Network
SUERM - Signal Unit Error Rate Monitor
TCBC - Changeback control
TCOC - Changeover control
TCRC - Controlled rerouting control
TFRC - Forced rerouting control
TLAC - Link availability control
TPRC - Signalling point restart control
TRCC - Signalling route set congestion control
TSFC - Signalling traffic flow control
TSRC - Signalling routing control
TTC - The Japanese Telecommunications Technology
Committee
WRR - Weighted round robin
Parsed from file CISCO-ITP-GSP-MIB.mib
Module: CISCO-ITP-GSP-MIB
The MIB for managing Signalling Points and its
associated messages transported over Signalling
System No. 7 (SS7) Network via Cisco IP Transfer
Point. This MIB replaces the CISCO-ITP-SP-MIB and
provide support multiple instances of a signalling
point within same configuration.
The Cisco IP Transfer Point (ITP) is a hardware
and software solution that transports SS7 traffic
using IP. Each ITP node provides function similar
to SS7 Signalling point.
The relevant ITU documents describing this technology
is the ITU Q series, including ITU Q.700: Introduction
to CCITT Signalling System No. 7 and ITU Q.701
Functional description of the message transfer part
(MTP) of Signalling System No. 7.
This MIB models the GSP as follows:
Abbreviations:
AERM - Alignment Error Rate Monitor
CLLI - Common-Language Location Identification
DPC - Destination Point Code
GSP - Gateway Signalling Point
HSL - High Speed Link (ATM based)
LLSC - link set control
LSAC - Signalling link activity control
LSDA - Signalling data link allocation
LSLA - Signalling link activation
LSLD - Signalling link deactivation
LSLR - Signalling link restoration
LSSU - Link Status Signal Unit
LSTA - Signalling terminal allocation
MTP - Message Transport Protocol
MTP2 - Layer 2 of Message Transport Protocol
MTP3 - Layer 3 of Message Transport Protocol
NTT - The Japanese Nippon Telephone & Telegraph
OPC - Originating Point Code
PC - Point Code
RTN - RouteTableName
SCTP - Stream Transmission Protocol(RFC 2960)
SIB - Status Indicator Busy
SLT - Signalling Link Test
SLTA - Signalling Link Test Acknowledgement
SP - Signalling Point
SS7 - System No. 7 (SS7) Network
SUERM - Signal Unit Error Rate Monitor
TCBC - Changeback control
TCOC - Changeover control
TCRC - Controlled rerouting control
TFRC - Forced rerouting control
TLAC - Link availability control
TPRC - Signalling point restart control
TRCC - Signalling route set congestion control
TSFC - Signalling traffic flow control
TSRC - Signalling routing control
TTC - The Japanese Telecommunications Technology
Committee
WRR - Weighted round robin
Parsed from file CISCO-ITP-GSP-MIB.my.txt
Company: None
Module: CISCO-ITP-GSP-MIB
The MIB for managing Signalling Points and its
associated messages transported over Signalling
System No. 7 (SS7) Network via Cisco IP Transfer
Point. This MIB replaces the CISCO-ITP-SP-MIB and
provide support multiple instances of a signalling
point within same configuration.
The Cisco IP Transfer Point (ITP) is a hardware
and software solution that transports SS7 traffic
using IP. Each ITP node provides function similar
to SS7 Signalling point.
The relevant ITU documents describing this technology
is the ITU Q series, including ITU Q.700: Introduction
to CCITT Signalling System No. 7 and ITU Q.701
Functional description of the message transfer part
(MTP) of Signalling System No. 7.
This MIB models the GSP as follows:
Abbreviations:
AERM - Alignment Error Rate Monitor
CLLI - Common-Language Location Identification
DPC - Destination Point Code
GSP - Gateway Signalling Point
HSL - High Speed Link (ATM based)
LLSC - link set control
LSAC - Signalling link activity control
LSDA - Signalling data link allocation
LSLA - Signalling link activation
LSLD - Signalling link deactivation
LSLR - Signalling link restoration
LSSU - Link Status Signal Unit
LSTA - Signalling terminal allocation
MTP - Message Transport Protocol
MTP2 - Layer 2 of Message Transport Protocol
MTP3 - Layer 3 of Message Transport Protocol
NTT - The Japanese Nippon Telephone & Telegraph
OPC - Originating Point Code
PC - Point Code
RTN - RouteTableName
SCTP - Stream Transmission Protocol(RFC 2960)
SIB - Status Indicator Busy
SLT - Signalling Link Test
SLTA - Signalling Link Test Acknowledgement
SP - Signalling Point
SS7 - System No. 7 (SS7) Network
SUERM - Signal Unit Error Rate Monitor
TCBC - Changeback control
TCOC - Changeover control
TCRC - Controlled rerouting control
TFRC - Forced rerouting control
TLAC - Link availability control
TPRC - Signalling point restart control
TRCC - Signalling route set congestion control
TSFC - Signalling traffic flow control
TSRC - Signalling routing control
TTC - The Japanese Telecommunications Technology
Committee
WRR - Weighted round robin
ciscoGspMIB MODULE-IDENTITY LAST-UPDATED "201003050000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin" REVISION "200912310000Z" DESCRIPTION "Added the cgspLinkRxCongestionState object into CgspLinkTableEntry and ciscoGspRxCongestionChange notification to notify state of cgspLinkRxCongestionState." REVISION "200909120000Z" DESCRIPTION "Added the opc value to the cgspInstSccpWrrOption textual convention." REVISION "200905250000Z" DESCRIPTION "Added the following objects into cgspInstanceTableEntry for GTT weighted loadshare. cgspInstSccpWrrOpcShift, cgspInstSccpWrrOption" REVISION "200805070000Z" DESCRIPTION "Added the following objects into CgspLinkTableEntry for additional Q752 related reporting. cgspLinkQ752T1E12, cgspLinkQ752T1E12Errors, cgspLinkQ752T2E11, cgspLinkQ752T2E17, cgspLinkQ752T2E19. Added linkRestored(34) and linkTestFailure(35) reason code to the cgspLinkReason object. Added the following textual convention: CgspDisplayInstanceUserPart. Added a new table cgspInstUPUTable with following objects: cgspMtp3SI, cgspInstSIUPUReceived, cgspInstSIUPUTransmitted, cgspInstUserPartDisplay. Added the following objects: cgspNotificationsInfo, cgspUPUNotifWindowTime. Added following new notifications: ciscoGspUPUReceived, ciscoGspUPUTransmitted. Added the following cgspNotificationsInfo objects: cgspUPUIntervalDuration, cgspIntervalUPUs." REVISION "200510210000Z" DESCRIPTION "Added new set of enums (from timerMtp2T01 to timerMtp2T07) to TC CgspTimerNumbers for MTP2 timers specified in ITU Q.703." REVISION "200502240000Z" DESCRIPTION "Added new ciscoGspIsolation notification to indicate when MTP3 node becomes isolated." REVISION "200307160000Z" DESCRIPTION "Additional reason codes to the cgspLinkReason object and updated CgspSS7Variant textual convention to support NTT and TTC Japanese variants. Also, update REFERENCE clauses to indicate support for appropriate ANSI standard." REVISION "200303030000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 336 }
ciscoGspMIB OBJECT IDENTIFIER ::= { ciscoMgmt 336 }
Vendor: Cisco
Module: CISCO-ITP-GSP-MIB
[Automatically extracted from oidview.com]
ciscoGspMIB MODULE-IDENTITY LAST-UPDATED "201003050000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin" REVISION "200912310000Z" DESCRIPTION "Added the cgspLinkRxCongestionState object into CgspLinkTableEntry and ciscoGspRxCongestionChange notification to notify state of cgspLinkRxCongestionState." REVISION "200909120000Z" DESCRIPTION "Added the opc value to the cgspInstSccpWrrOption textual convention." REVISION "200905250000Z" DESCRIPTION "Added the following objects into cgspInstanceTableEntry for GTT weighted loadshare. cgspInstSccpWrrOpcShift, cgspInstSccpWrrOption" REVISION "200805070000Z" DESCRIPTION "Added the following objects into CgspLinkTableEntry for additional Q752 related reporting. cgspLinkQ752T1E12, cgspLinkQ752T1E12Errors, cgspLinkQ752T2E11, cgspLinkQ752T2E17, cgspLinkQ752T2E19. Added linkRestored(34) and linkTestFailure(35) reason code to the cgspLinkReason object. Added the following textual convention: CgspDisplayInstanceUserPart. Added a new table cgspInstUPUTable with following objects: cgspMtp3SI, cgspInstSIUPUReceived, cgspInstSIUPUTransmitted, cgspInstUserPartDisplay. Added the following objects: cgspNotificationsInfo, cgspUPUNotifWindowTime. Added following new notifications: ciscoGspUPUReceived, ciscoGspUPUTransmitted. Added the following cgspNotificationsInfo objects: cgspUPUIntervalDuration, cgspIntervalUPUs." REVISION "200510210000Z" DESCRIPTION "Added new set of enums (from timerMtp2T01 to timerMtp2T07) to TC CgspTimerNumbers for MTP2 timers specified in ITU Q.703." REVISION "200502240000Z" DESCRIPTION "Added new ciscoGspIsolation notification to indicate when MTP3 node becomes isolated." REVISION "200307160000Z" DESCRIPTION "Additional reason codes to the cgspLinkReason object and updated CgspSS7Variant textual convention to support NTT and TTC Japanese variants. Also, update REFERENCE clauses to indicate support for appropriate ANSI standard." REVISION "200303030000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 336 }
ciscoGspMIB MODULE-IDENTITY LAST-UPDATED "201003050000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin" REVISION "200912310000Z" DESCRIPTION "Added the cgspLinkRxCongestionState object into CgspLinkTableEntry and ciscoGspRxCongestionChange notification to notify state of cgspLinkRxCongestionState." REVISION "200909120000Z" DESCRIPTION "Added the opc value to the cgspInstSccpWrrOption textual convention." REVISION "200905250000Z" DESCRIPTION "Added the following objects into cgspInstanceTableEntry for GTT weighted loadshare. cgspInstSccpWrrOpcShift, cgspInstSccpWrrOption" REVISION "200805070000Z" DESCRIPTION "Added the following objects into CgspLinkTableEntry for additional Q752 related reporting. cgspLinkQ752T1E12, cgspLinkQ752T1E12Errors, cgspLinkQ752T2E11, cgspLinkQ752T2E17, cgspLinkQ752T2E19. Added linkRestored(34) and linkTestFailure(35) reason code to the cgspLinkReason object. Added the following textual convention: CgspDisplayInstanceUserPart. Added a new table cgspInstUPUTable with following objects: cgspMtp3SI, cgspInstSIUPUReceived, cgspInstSIUPUTransmitted, cgspInstUserPartDisplay. Added the following objects: cgspNotificationsInfo, cgspUPUNotifWindowTime. Added following new notifications: ciscoGspUPUReceived, ciscoGspUPUTransmitted. Added the following cgspNotificationsInfo objects: cgspUPUIntervalDuration, cgspIntervalUPUs." REVISION "200510210000Z" DESCRIPTION "Added new set of enums (from timerMtp2T01 to timerMtp2T07) to TC CgspTimerNumbers for MTP2 timers specified in ITU Q.703." REVISION "200502240000Z" DESCRIPTION "Added new ciscoGspIsolation notification to indicate when MTP3 node becomes isolated." REVISION "200307160000Z" DESCRIPTION "Additional reason codes to the cgspLinkReason object and updated CgspSS7Variant textual convention to support NTT and TTC Japanese variants. Also, update REFERENCE clauses to indicate support for appropriate ANSI standard." REVISION "200303030000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 336 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.336.0 | ciscoGspMIBNotifs | 9 | 9 | None |
| 1.3.6.1.4.1.9.9.336.1 | ciscoGspMIBObjects | 8 | 228 | None |
| 1.3.6.1.4.1.9.9.336.2 | ciscoGspMIBConform | 2 | 33 | None |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.9.9.286 | ciscoWwnmgrMIB | 2 | 38 | The World Wide Name (WWN) in the fibre channel networking technology is equivalent to the MAC address in Ethernet. There are six … |
| 1.3.6.1.4.1.9.9.287 | ciscoFspfMIB | 4 | 95 | Fabric Shortest Path First (FSPF) MIB. |
| 1.3.6.1.4.1.9.9.288 | ciscoRadiusMIB | 3 | 91 | MIB module for monitoring and configuring authentication and logging services using RADIUS (Remote Authentication Dial In User Se… |
| 1.3.6.1.4.1.9.9.289 | ciscoFcFeMIB | 2 | 315 | This is the Cisco fibre element management MIB module. It covers: - Cisco extension to the interface MIB ( IF-MIB ) - Contains all… |
| 1.3.6.1.4.1.9.9.290 | ciscoVirtualNwIfMIB | 2 | 22 | The MIB module for management of virtual network interfaces to VSAN and VLAN. |
| 1.3.6.1.4.1.9.9.292 | ciscoRscnMIB | 2 | 67 | The MIB module for the management of the Fibre Channel's Registered State Change Notification (RSCN) functionality, which is spec… |
| 1.3.6.1.4.1.9.9.293 | ciscoNsMIB | 2 | 67 | The MIB module for the management of the Cisco Name Server which realizes the FC-GS3 requirements for Name Server (NS). |
| 1.3.6.1.4.1.9.9.294 | ciscoZsMIB | 2 | 254 | The MIB module for the management of zoning within the framework of Cisco's Zoning Server (ZS) Archi- tecture which realizes the … |
| 1.3.6.1.4.1.9.9.295 | ciscoFcPingMIB | 2 | 37 | The MIB module for the management of the Fibre Channel Ping functionality. |
| 1.3.6.1.4.1.9.9.296 | ciscoFcTraceRouteMIB | 2 | 31 | The MIB module for the management of the Fibre Channel Trace Route functionality. |
| 1.3.6.1.4.1.9.9.297 | ciscoFcsMIB | 2 | 122 | The MIB module for the management of a Fabric Configuration Server (FCS). An FCS is defined by the FC-GS3 standard. This MIB ena… |
| 1.3.6.1.4.1.9.9.299 | ciscoExtScsiMIB | 2 | 68 | The Cisco extension to CISCO-SCSI-MIB which is a copy of the Internet draft, the SCSI-MIB, from the IETF. Glossary of terms used i… |
| 1.3.6.1.4.1.9.9.300 | ciscoCallHomeMIB | 3 | 324 | The MIB module for the management of Call Home feature within the framework of Cisco's Call Home architecture. Customers deployin… |
| 1.3.6.1.4.1.9.9.301 | ciscoSyslogExtMIB | 2 | 44 | MIB module for configuring and monitoring System Log related management parameters as defined by RFC 3164. |
| 1.3.6.1.4.1.9.9.302 | ciscoDmMIB | 2 | 85 | The MIB module for the domain management functionality defined by the Fibre Channel standards (FC-SW2). For the purposes of this … |
| 1.3.6.1.4.1.9.9.305 | ciscoSystemExtMIB | 3 | 112 | MIB module for monitoring High Availability, SNMP SET errors and bandwidths. This mib module also provides the information on co… |
| 1.3.6.1.4.1.9.9.309 | ciscoIPIfMIB | 3 | 40 | The MIB module for configuring IP characteristics of the interfaces of a device. |
| 1.3.6.1.4.1.9.9.311 | ciscoEpmNotificationMIB | 3 | 48 | Notifications directly from hardware and software and processed notifications from various management applications can be furthe… |
| 1.3.6.1.4.1.9.9.312 | ciscoDataCollectionMIB | 3 | 84 | The MIB module allows a management application to select a set of MIB object instances whose values need to be collected on a per… |
| 1.3.6.1.4.1.9.9.313 | ciscoL2ControlMIB | 3 | 113 | The CISCO-L2-CONTROL-MIB is used to control some layer 2 functions, including MAC limit function and unicast flooding. This devi… |
| 1.3.6.1.4.1.9.9.314 | ciscoCasIfExtMIB | 3 | 225 | The MIB module is an extension of CISCO-CAS-IF-MIB. It defines the attributes of a voice interface. |
| 1.3.6.1.4.1.9.9.315 | ciscoPortSecurityMIB | 3 | 89 | The MIB module for managing Cisco Port Security. |
| 1.3.6.1.4.1.9.9.317 | ciscoIscsiGwMIB | 3 | 145 | MIB module for monitoring and configuring iSCSI gateway functions. An iSCSI gateway represents FC (Fibre Channel) targets/initiat… |
| 1.3.6.1.4.1.9.9.318 | ciscoXgcpMIB | 3 | 120 | This MIB is an enhancement for existing XGCP-MIB. xGCP is a set of protocols, for example SGCP (Simple Gateway Control Protocol) … |
| 1.3.6.1.4.1.9.9.319 | ciscoPropAtmIfMIB | 3 | 57 | This MIB is designed for Propietary ATM (propAtm) interfaces. The propAtm interfaces are identified in the ifTable entries with if… |
| 1.3.6.1.4.1.9.9.321 | ciscoMgcMIB | 3 | 43 | This MIB is used to support MGC(call agent) and MGC Group configuration. The MGC or MGC group configuration is performed under a s… |
| 1.3.6.1.4.1.9.9.322 | ccacSysMIB | 2 | 60 | This MIB module provides provisioning and monitoring Call Admission Control (CAC). |
| 1.3.6.1.4.1.9.9.323 | ciscoVoiceAalxProfileMIB | 3 | 87 | This MIB defines the objects specific to voice over ATM or voice over IP. Those objects are related to the following areas: 1. COD… |
| 1.3.6.1.4.1.9.9.324 | ciscoMediaGatewayMIB | 3 | 107 | The MIB module for managing Trunk Media Gateway. A Media Gateway is a network element that provides conversion between the audio … |
| 1.3.6.1.4.1.9.9.325 | ciscoXgcpExtMIB | 2 | 65 | This MIB module is an extension to CISCO-XGCP-MIB. It defines the parameters related to the following aspects in xGCP protocols: *… |
| 1.3.6.1.4.1.9.9.326 | ciscoIpLocalPoolMIB | 3 | 57 | This MIB defines the configuration and monitoring capabilities relating to local IP pools. Local IP pools have the following char… |
| 1.3.6.1.4.1.9.9.329 | ciscoFcipMgmtExtMIB | 3 | 75 | A MIB module for extending the CISCO-FCIP-MGMT-MIB to add objects which provide additional information about FCIP interfaces not … |
| 1.3.6.1.4.1.9.9.330 | ciscoSysInfoLogMIB | 3 | 44 | This MIB provides the configuration of System Information Logging feature, which allows a certain number of commands to be execut… |
| 1.3.6.1.4.1.9.9.331 | ciscoCsgMIB | 3 | 86 | This MIB supports the Cisco Content Services Gateway (CSG) product. It includes five traps and four tables that enable querying C… |
| 1.3.6.1.4.1.9.9.332 | ciscoGsp2MIB | 3 | 91 | The MIB for providing information specified in ITU Q752 Monitoring and Measurements for signalling System No. 7(SS7) Network. This… |
| 1.3.6.1.4.1.9.9.333 | ciscoGactMIB | 3 | 40 | The MIB for providing information specified in ITU Q752 Monitoring and Measurements for Signalling System No. 7(SS7) Network. This… |
| 1.3.6.1.4.1.9.9.334 | ciscoGrtMIB | 3 | 150 | This MIB is for managing information required to route messages transported over Signalling System No. 7 (SS7) Network via Cisco … |
| 1.3.6.1.4.1.9.9.335 | ciscoGsccpMIB | 3 | 293 | The MIB for signalling Connection Control Part(SCCP) messages transported over Signalling System No. 7 (SS7) Network via Cisco IP… |
| 1.3.6.1.4.1.9.9.339 | ciscoSecureShellMIB | 2 | 40 | MIB module for displaying and configuring accounting and Secure Shell (SSH) related features in a device. SSH is a program to log … |
| 1.3.6.1.4.1.9.9.340 | ciscoLreCpeMIB | 3 | 21 | The MIB module for the Cisco Long Reach Ethernet Customer Premise Equipment device information. *** ABBREVIATIONS, ACRONYMS, AND … |
| 1.3.6.1.4.1.9.9.341 | ciscoCableQosMonitorMIB | 3 | 57 | This is the MIB module for subscriber QoS monitoring for DOCSIS-compliant Cable Modem Termination Systems (CMTS). Several subscrib… |
| 1.3.6.1.4.1.9.9.343 | ciscoAuthorizationStatsMibModule | 2 | 25 | The Cisco User Authorization Statistics MIB models counters and objects that are of management interest. |
| 1.3.6.1.4.1.9.9.344 | ciscoEntityDisplayMIB | 2 | 21 | This MIB module provides information about the status of display devices such as Light Emitting Diodes (LEDs) and alphanumeric di… |
| 1.3.6.1.4.1.9.9.350 | ciscoEntityDiagMIB | 3 | 139 | This MIB module defines the managed objects that describe the online diagnostics capabilities supported by the physical entities … |
| 1.3.6.1.4.1.9.9.351 | ciscoAtmTrunkMIB | 3 | 102 | The MIB for voice and Nx64 over ATM Trunking applications. The following lists the abbreviations used in this MIB: AAL ATM … |
| 1.3.6.1.4.1.9.9.356 | ciscoVoiceToneCadenceMIB | 3 | 30 | The MIB defines the attributes of the programmable tones specified in ITU-T E.180 Supplement 2. Each country has its own regulati… |
| 1.3.6.1.4.1.9.9.358 | ciscoBbsmMIB | 3 | 20 | This mib is designed to send BBSM specific notifications. There are variables that contain detail data that are bind to a notifi… |
| 1.3.6.1.4.1.9.9.359 | ciscoLicenseMIB | 3 | 52 | This MIB module provides objects to view the features and services that are licensed to run on a system (usually a network entity… |
| 1.3.6.1.4.1.9.9.360 | ciscoImageUpgradeMIB | 3 | 101 | This mib provides, objects to upgrade images on modules in the system, objects showing the status of the upgrade operation, and o… |
| 1.3.6.1.4.1.9.9.361 | ciscoCommonRolesMIB | 3 | 40 | MIB module for managing the common roles between access methods like Command Line Interface (CLI), SNMP and XML interfaces. Every … |
| 1.3.6.1.4.1.9.9.362 | ciscoPortStormControlMIB | 3 | 41 | The MIB module for managing Cisco Port Storm Control. |
| 1.3.6.1.4.1.9.9.363 | ciscoFcSpanMIB | 2 | 49 | MIB module for displaying and configuring Switched Port Analyzer(SPAN) related features in a Fibre Channel device. SPAN is a featu… |
| 1.3.6.1.4.1.9.9.364 | ciscoPsmMIB | 3 | 213 | The MIB module for the management of the Port Security Manager (PSM). The PSM consists of 2 aspects: Port binding and Fabric bindi… |
| 1.3.6.1.4.1.9.9.365 | ciscoFCCMIB | 3 | 42 | The MIB module for the management of Fibre Channel Congestion Control(FCC). FCC is a Cisco proprietary flow control mechanism tha… |
| 1.3.6.1.4.1.9.9.367 | ciscoAAAServerExtMIB | 2 | 77 | This MIB is an extension to the CISCO-AAA-SERVER-MIB. This MIB module enhances the 'casConfigTable' to include other types of Ser… |
| 1.3.6.1.4.1.9.9.368 | 368 | 0 | 0 | Cisco Content Services (CSS) switch product, also known as Arrowpoint, for version 7.40 and later |
| 1.3.6.1.4.1.9.9.369 | ciscoLicenseMgrMIB | 3 | 74 | The MIB module for a method of managing license files on the system. Licensing mechanism provides more flexibility in supporting v… |
| 1.3.6.1.4.1.9.9.370 | ciscoSslProxyMIB | 3 | 372 | This MIB module is for managing a Secure Socket Layer (SSL) Proxy device which terminates and accelarates SSL and Transport Layer… |
| 1.3.6.1.4.1.9.9.371 | ciscoIvrMIB | 3 | 192 | The MIB module for the management of Inter-VSAN routing within the framework of Cisco's Inter-VSAN Routing (IVR) Architecture. IV… |
| 1.3.6.1.4.1.9.9.372 | ciscoIsnsClientMIB | 3 | 16 | MIB module for monitoring and configuring Internet Storage Name Service (iSNS) client. |
| 1.3.6.1.4.1.9.9.373 | ciscoFdmiMIB | 3 | 47 | Fabric Device Management Interface (FDMI) MIB. This MIB module defines objects for managing the devices such as HBA (Host Bus Ada… |
| 1.3.6.1.4.1.9.9.374 | ciscoDynamicArpInspectionMIB | 3 | 82 | The MIB module is for configuration of Dynamic ARP Inspection feature. Dynamic ARP Inspection is a security mechanism which valid… |
| 1.3.6.1.4.1.9.9.375 | ciscoFiconMIB | 3 | 176 | This is the FICON (FIber CONnection) MIB module. FICON is an IBM standard of transport mechanism for communication between the ma… |
| 1.3.6.1.4.1.9.9.376 | ciscoSVIAutostateMIB | 3 | 19 | The MIB module is for configuration of the switch virtual interface (SVI) autostate feature. Autostate feature is a mechanism to … |
| 1.3.6.1.4.1.9.9.377 | ciscoFeatureCtrlMIB | 3 | 53 | There are two types of features in the system: - Regular features - Optional features The Regular features may or may not need to … |
| 1.3.6.1.4.1.9.9.378 | ciscoSvcInterfaceMIB | 3 | 115 | MIB module for displaying and configuring SVC (SAN Volume Controller) related features in the Storage Area Network (SAN) switches… |
| 1.3.6.1.4.1.9.9.379 | ciscoItpmMIB | 3 | 47 | The MIB for providing information related to monitoring SS7 links. This information can be used to manage the state of software u… |
| 1.3.6.1.4.1.9.9.380 | ciscoDhcpSnoopingMIB | 3 | 127 | The MIB module is for configuration of DHCP Snooping feature. DHCP Snooping is a security mechanism which uses information gleane… |
| 1.3.6.1.4.1.9.9.381 | ciscoDiffServExtMIB | 2 | 49 | This MIB is a Cisco extension to the DIFFSERV-MIB, RFC 3289. This MIB defines a Fibre Channel (FC) Multi Field filter to be used i… |
| 1.3.6.1.4.1.9.9.383 | ciscoCidsMIB | 3 | 183 | Cisco Intrusion Detection System MIB. Provides trap definitions for the evAlert and evError elements of the IDIOM (Intrusion Det… |
| 1.3.6.1.4.1.9.9.384 | ciscoDot11AntennaMIB | 2 | 11 | This MIB is intended to be implemented on 802.11 Access Points and Wireless Bridges to provide information about the antennas con… |
| 1.3.6.1.4.1.9.9.385 | ciscoUnityMIB | 3 | 101 | The MIB Module for the management of Cisco Unity server. Cisco Unity is a Unified Communications solution that provides advanced,… |
| 1.3.6.1.4.1.9.9.386 | ciscoModuleAutoShutdownMIB | 3 | 36 | The CISCO-MODULE-AUTO-SHUTDOWN-MIB is used to configure the module automatic shutdown feature. Modules will be reset by the syste… |
| ... | ||||