This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
(LWAPP) tunnel from Light-weight Access Points.
This MIB represents information about the status of the
Multipurpose Power Supply (MPS), used as backup power
supply for an Access Point (AP) in the Wireless Mesh Network.
The MPS reports status information to the AP periodically.
The AP inturn reports the battery status information to the
controller periodically as a part of the LWAPP information packet.
General Infomation about Cisco Wireless Mesh network:
A Mesh AP (MAP) can associate directly with another Root AP (RAP)
or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP)
with another AP forms parent-child relationship.
The arrangement of the controller
(referred to as CC in the diagram) and mesh nodes
(RAP and MAP) LWAPP APs ,client(MN) and NMS appear
as follows.
+.......+ +.......+
+ + + +
+ NMS + + NMS +
+ + + +
+.......+ +.......+
. .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ RAP + + RAP + + RAP + + RAP + + RAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MAP + + MN + + MAP + + MAP + + MAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . .. .
. . . .. .
. . . .. .
. . . . .
+......+ +......+ +......+ +......+. +......+
+ + + + + + + + + +
+ MAP + + MAP + + MAP + + MAP + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the
configuration, that includes the WLAN parameters, to
the LWAPP APs through the tunnel.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point (AP)
An entity that contains an 802.11 medium access
control (MAC) and physical layer (PHY) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Central Controller (CC)
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity is also referred to as 'controller'.
Mobile Node (MN)
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
Network Management System (NMS)
The station from which the administrator manages the
wired and wireless networks.
Mesh Network
A network of APs where the AP are linked to each other through
wireless links. These wireless links are also called backhaul
links. At least one of these APs must be connected to a
controller through a wired link.
Mesh Node
A mesh node is defined as a physical or logical entity
in the mesh network participating in forming the mesh
backhaul. There are two types of mesh nodes supported
in Cisco mesh network - RAP and MAP.
Root AP (RAP)
The AP forming the bridge between a wired and a mesh
network with an Ethernet interface to the wired
network and a 802.11 radio interface to the mesh
network.
Mesh AP (MAP).
The AP extending wireless coverage similar to a
repeater in a mesh network and consists of a 802.11
uplink and a 802.11 downlink. On a single-radio
backhaul, both uplink and downlink exist on the same
radio and are logical links only. On a multi-radio
backhaul, they may exist on different radios.
REFERENCE
[1] Wireless LAN Medium Access Control (MAC) and
Physical Layer (PHY) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol.
Parsed from file CISCO-LWAPP-MESH-BATTERY-MIB.mib
Module: CISCO-LWAPP-MESH-BATTERY-MIB
This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
(LWAPP) tunnel from Light-weight Access Points.
This MIB represents information about the status of the
Multipurpose Power Supply (MPS), used as backup power
supply for an Access Point (AP) in the Wireless Mesh Network.
The MPS reports status information to the AP periodically.
The AP inturn reports the battery status information to the
controller periodically as a part of the LWAPP information packet.
General Infomation about Cisco Wireless Mesh network:
A Mesh AP (MAP) can associate directly with another Root AP (RAP)
or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP)
with another AP forms parent-child relationship.
The arrangement of the controller
(referred to as CC in the diagram) and mesh nodes
(RAP and MAP) LWAPP APs ,client(MN) and NMS appear
as follows.
+.......+ +.......+
+ + + +
+ NMS + + NMS +
+ + + +
+.......+ +.......+
. .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ RAP + + RAP + + RAP + + RAP + + RAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MAP + + MN + + MAP + + MAP + + MAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . .. .
. . . .. .
. . . .. .
. . . . .
+......+ +......+ +......+ +......+. +......+
+ + + + + + + + + +
+ MAP + + MAP + + MAP + + MAP + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the
configuration, that includes the WLAN parameters, to
the LWAPP APs through the tunnel.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point (AP)
An entity that contains an 802.11 medium access
control (MAC) and physical layer (PHY) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Central Controller (CC)
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity is also referred to as 'controller'.
Mobile Node (MN)
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
Network Management System (NMS)
The station from which the administrator manages the
wired and wireless networks.
Mesh Network
A network of APs where the AP are linked to each other through
wireless links. These wireless links are also called backhaul
links. At least one of these APs must be connected to a
controller through a wired link.
Mesh Node
A mesh node is defined as a physical or logical entity
in the mesh network participating in forming the mesh
backhaul. There are two types of mesh nodes supported
in Cisco mesh network - RAP and MAP.
Root AP (RAP)
The AP forming the bridge between a wired and a mesh
network with an Ethernet interface to the wired
network and a 802.11 radio interface to the mesh
network.
Mesh AP (MAP).
The AP extending wireless coverage similar to a
repeater in a mesh network and consists of a 802.11
uplink and a 802.11 downlink. On a single-radio
backhaul, both uplink and downlink exist on the same
radio and are logical links only. On a multi-radio
backhaul, they may exist on different radios.
REFERENCE
[1] Wireless LAN Medium Access Control (MAC) and
Physical Layer (PHY) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol.
Parsed from file CISCO-LWAPP-MESH-BATTERY-MIB.my.txt
Company: None
Module: CISCO-LWAPP-MESH-BATTERY-MIB
This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
(LWAPP) tunnel from Light-weight Access Points.
This MIB represents information about the status of the
Multipurpose Power Supply (MPS), used as backup power
supply for an Access Point (AP) in the Wireless Mesh Network.
The MPS reports status information to the AP periodically.
The AP inturn reports the battery status information to the
controller periodically as a part of the LWAPP information
packet.
General Infomation about Cisco Wireless Mesh network:
A Mesh AP (MAP) can associate directly with another
Root AP (RAP) or with another MAP AP.
Each association of AP (MAP-MAP or RAP-MAP)
with another AP forms parent-child relationship.
The arrangement of the controller
(referred to as CC in the diagram) and mesh nodes
(RAP and MAP) LWAPP APs ,client(MN) and NMS appear
as follows.
+.......+ +.......+
+ + + +
+ NMS + + NMS +
+ + + +
+.......+ +.......+
. .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ RAP + + RAP + + RAP + + RAP + + RAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MAP + + MN + + MAP + + MAP + + MAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . .. .
. . . .. .
. . . .. .
. . . . .
+......+ +......+ +......+ +......+. +......+
+ + + + + + + + + +
+ MAP + + MAP + + MAP + + MAP + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the
configuration, that includes the WLAN parameters, to
the LWAPP APs through the tunnel.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point (AP)
An entity that contains an 802.11 medium access
control (MAC) and physical layer (PHY) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Central Controller (CC)
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity is also referred to as 'controller'.
Mobile Node (MN)
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
Network Management System (NMS)
The station from which the administrator manages the
wired and wireless networks.
Mesh Network
A network of APs where the AP are linked to each other through
wireless links. These wireless links are also called backhaul
links. At least one of these APs must be connected to a
controller through a wired link.
Mesh Node
A mesh node is defined as a physical or logical entity
in the mesh network participating in forming the mesh
backhaul. There are two types of mesh nodes supported
in Cisco mesh network - RAP and MAP.
Root AP (RAP)
The AP forming the bridge between a wired and a mesh
network with an Ethernet interface to the wired
network and a 802.11 radio interface to the mesh
network.
Mesh AP (MAP).
The AP extending wireless coverage similar to a
repeater in a mesh network and consists of a 802.11
uplink and a 802.11 downlink. On a single-radio
backhaul, both uplink and downlink exist on the same
radio and are logical links only. On a multi-radio
backhaul, they may exist on different radios.
REFERENCE
[1] Wireless LAN Medium Access Control (MAC) and
Physical Layer (PHY) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol.
ciscoLwappMeshBatteryMIB MODULE-IDENTITY LAST-UPDATED "200703130000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: [email protected]" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol (LWAPP) tunnel from Light-weight Access Points. This MIB represents information about the status of the Multipurpose Power Supply (MPS), used as backup power supply for an Access Point (AP) in the Wireless Mesh Network. The MPS reports status information to the AP periodically. The AP inturn reports the battery status information to the controller periodically as a part of the LWAPP information packet. General Infomation about Cisco Wireless Mesh network: A Mesh AP (MAP) can associate directly with another Root AP (RAP) or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP) with another AP forms parent-child relationship. The arrangement of the controller (referred to as CC in the diagram) and mesh nodes (RAP and MAP) LWAPP APs ,client(MN) and NMS appear as follows. +.......+ +.......+ + + + + + NMS + + NMS + + + + + +.......+ +.......+ . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + RAP + + RAP + + RAP + + RAP + + RAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MAP + + MN + + MAP + + MAP + + MAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . .. . . . . .. . . . . .. . . . . . . +......+ +......+ +......+ +......+. +......+ + + + + + + + + + + + MAP + + MAP + + MAP + + MAP + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs through the tunnel. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point (AP) An entity that contains an 802.11 medium access control (MAC) and physical layer (PHY) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller (CC) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Mobile Node (MN) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Network Management System (NMS) The station from which the administrator manages the wired and wireless networks. Mesh Network A network of APs where the AP are linked to each other through wireless links. These wireless links are also called backhaul links. At least one of these APs must be connected to a controller through a wired link. Mesh Node A mesh node is defined as a physical or logical entity in the mesh network participating in forming the mesh backhaul. There are two types of mesh nodes supported in Cisco mesh network - RAP and MAP. Root AP (RAP) The AP forming the bridge between a wired and a mesh network with an Ethernet interface to the wired network and a 802.11 radio interface to the mesh network. Mesh AP (MAP). The AP extending wireless coverage similar to a repeater in a mesh network and consists of a 802.11 uplink and a 802.11 downlink. On a single-radio backhaul, both uplink and downlink exist on the same radio and are logical links only. On a multi-radio backhaul, they may exist on different radios. REFERENCE [1] Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol." REVISION "200702270000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 620 }
ciscoLwappMeshBatteryMIB OBJECT IDENTIFIER ::= { ciscoMgmt 620 }
Vendor: Cisco
Module: CISCO-LWAPP-MESH-BATTERY-MIB
[Automatically extracted from oidview.com]
ciscoLwappMeshBatteryMIB MODULE-IDENTITY LAST-UPDATED "200703130000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: [email protected]" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol (LWAPP) tunnel from Light-weight Access Points. This MIB represents information about the status of the Multipurpose Power Supply (MPS), used as backup power supply for an Access Point (AP) in the Wireless Mesh Network. The MPS reports status information to the AP periodically. The AP inturn reports the battery status information to the controller periodically as a part of the LWAPP information packet. General Infomation about Cisco Wireless Mesh network: A Mesh AP (MAP) can associate directly with another Root AP (RAP) or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP) with another AP forms parent-child relationship. The arrangement of the controller (referred to as CC in the diagram) and mesh nodes (RAP and MAP) LWAPP APs ,client(MN) and NMS appear as follows. +.......+ +.......+ + + + + + NMS + + NMS + + + + + +.......+ +.......+ . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + RAP + + RAP + + RAP + + RAP + + RAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MAP + + MN + + MAP + + MAP + + MAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . .. . . . . .. . . . . .. . . . . . . +......+ +......+ +......+ +......+. +......+ + + + + + + + + + + + MAP + + MAP + + MAP + + MAP + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs through the tunnel. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point (AP) An entity that contains an 802.11 medium access control (MAC) and physical layer (PHY) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller (CC) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Mobile Node (MN) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Network Management System (NMS) The station from which the administrator manages the wired and wireless networks. Mesh Network A network of APs where the AP are linked to each other through wireless links. These wireless links are also called backhaul links. At least one of these APs must be connected to a controller through a wired link. Mesh Node A mesh node is defined as a physical or logical entity in the mesh network participating in forming the mesh backhaul. There are two types of mesh nodes supported in Cisco mesh network - RAP and MAP. Root AP (RAP) The AP forming the bridge between a wired and a mesh network with an Ethernet interface to the wired network and a 802.11 radio interface to the mesh network. Mesh AP (MAP). The AP extending wireless coverage similar to a repeater in a mesh network and consists of a 802.11 uplink and a 802.11 downlink. On a single-radio backhaul, both uplink and downlink exist on the same radio and are logical links only. On a multi-radio backhaul, they may exist on different radios. REFERENCE [1] Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol." REVISION "200702270000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 620 }
ciscoLwappMeshBatteryMIB MODULE-IDENTITY LAST-UPDATED "201009080000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: [email protected]" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol (LWAPP) tunnel from Light-weight Access Points. This MIB represents information about the status of the Multipurpose Power Supply (MPS), used as backup power supply for an Access Point (AP) in the Wireless Mesh Network. The MPS reports status information to the AP periodically. The AP inturn reports the battery status information to the controller periodically as a part of the LWAPP information packet. General Infomation about Cisco Wireless Mesh network: A Mesh AP (MAP) can associate directly with another Root AP (RAP) or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP) with another AP forms parent-child relationship. The arrangement of the controller (referred to as CC in the diagram) and mesh nodes (RAP and MAP) LWAPP APs ,client(MN) and NMS appear as follows. +.......+ +.......+ + + + + + NMS + + NMS + + + + + +.......+ +.......+ . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + RAP + + RAP + + RAP + + RAP + + RAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MAP + + MN + + MAP + + MAP + + MAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . .. . . . . .. . . . . .. . . . . . . +......+ +......+ +......+ +......+. +......+ + + + + + + + + + + + MAP + + MAP + + MAP + + MAP + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs through the tunnel. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point (AP) An entity that contains an 802.11 medium access control (MAC) and physical layer (PHY) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller (CC) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Mobile Node (MN) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Network Management System (NMS) The station from which the administrator manages the wired and wireless networks. Mesh Network A network of APs where the AP are linked to each other through wireless links. These wireless links are also called backhaul links. At least one of these APs must be connected to a controller through a wired link. Mesh Node A mesh node is defined as a physical or logical entity in the mesh network participating in forming the mesh backhaul. There are two types of mesh nodes supported in Cisco mesh network - RAP and MAP. Root AP (RAP) The AP forming the bridge between a wired and a mesh network with an Ethernet interface to the wired network and a 802.11 radio interface to the mesh network. Mesh AP (MAP). The AP extending wireless coverage similar to a repeater in a mesh network and consists of a 802.11 uplink and a 802.11 downlink. On a single-radio backhaul, both uplink and downlink exist on the same radio and are logical links only. On a multi-radio backhaul, they may exist on different radios. REFERENCE [1] Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol." REVISION "201009080000Z" DESCRIPTION "Added:- clMeshNodeBatteryCurrentValue, ciscoLwappMeshBatteryMIBComplianceRev2, ciscoLwappMeshBatteryInfoGroupRev1, ciscoLwappMeshBatteryInfoGroupRev2 Deprecated:- clMeshNodeBatteryChargingState, clMeshNodeBatteryRemainingCapacity, clMeshNodeBatteryCurrent." REVISION "200702270000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 620 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.620.0 | ciscoLwappMeshBatteryMIBNotifs | 1 | 1 | None |
| 1.3.6.1.4.1.9.9.620.1 | ciscoLwappMeshBatteryMIBObjects | 2 | 20 | None |
| 1.3.6.1.4.1.9.9.620.2 | ciscoLwappMeshBatteryMIBConform | 2 | 10 | None |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.9.9.572 | ciscoRttMonIPExtMIB | 2 | 38 | This MIB contains extensions to tables in CISCO-RTTMON-MIB to support IP-layer extensions, specifically IPv6 addresses and other … |
| 1.3.6.1.4.1.9.9.573 | ciscoQosTcMIB | 0 | 0 | This module defines the textual conventions used within Cisco Qos MIBs. |
| 1.3.6.1.4.1.9.9.576 | ciscoLwappMobilityMIB | 3 | 60 | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight… |
| 1.3.6.1.4.1.9.9.577 | ciscoLwappAclMIB | 3 | 26 | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight… |
| 1.3.6.1.4.1.9.9.578 | ciscoRoutePoliciesMIB | 3 | 5 | This module provides a subtree to define OIDs so that various routing 'policies' used by Cisco routers can be expressed. This mod… |
| 1.3.6.1.4.1.9.9.580 | ciscoSwitchQosMIB | 3 | 295 | This MIB module extends the CISCO-CLASS-BASED-QOS-MIB by defining configuration and statistics information specific to the qualit… |
| 1.3.6.1.4.1.9.9.583 | ciscoGslbTcMIB | 0 | 0 | This MIB module defines Textual Conventions and OBJECT-IDENTITIES for use in documents defining management information base (MIBs… |
| 1.3.6.1.4.1.9.9.584 | ciscoEntityDiagTcMIB | 0 | 0 | This module defines the textual conventions used within Cisco Entity Diag MIB. |
| 1.3.6.1.4.1.9.9.585 | ciscoIpSlaEthernetMIB | 3 | 194 | This MIB module consists of two parts. 1) Auto-Ethernet-CFM Control: | | 2) ethernetJitter Stats: | | The first part defines a mechani… |
| 1.3.6.1.4.1.9.9.586 | ciscoNotificationControlMIB | 2 | 28 | This MIB provides network management support to regulate the transmission of notifications generated by a system providing networ… |
| 1.3.6.1.4.1.9.9.589 | ciscoGslbSystemMIB | 3 | 103 | This MIB module defines objects for network and system information of Global Server Load Balancer(GSLB) as a network device. A G… |
| 1.3.6.1.4.1.9.9.590 | ciscoCvpMIB | 3 | 255 | The Cisco Unified Customer Voice Portal (CVP) application integrates with both traditional time-division multiplexing (TDM) and I… |
| 1.3.6.1.4.1.9.9.592 | ciscoPrefPathMIB | 3 | 56 | The MIB module for the management of preferred path. This MIB enables managers to configure and monitor Preferred Path parameters.… |
| 1.3.6.1.4.1.9.9.593 | ciscoFcSdvMIB | 3 | 28 | This MIB instrumentation is for managing Fibre Channel (FC) SAN Device Virtualization (SDV) solution on Cisco Fibre Channel devic… |
| 1.3.6.1.4.1.9.9.594 | ciscoApplicationAccelerationMIB | 3 | 37 | This is a MIB for managing Application Acceleration System(s). This MIB includes instrumentation for providing the performance st… |
| 1.3.6.1.4.1.9.9.595 | ciscoGslbDnsMIB | 3 | 165 | The MIB defines objects for status and statistics information of DNS related operations of Global Server Load Balancer(GSLB). Th… |
| 1.3.6.1.4.1.9.9.597 | ciscoContentServicesMIB | 3 | 349 | Content Service is a capability to examine IP/TCP/UDP headers, payload and enable billing based on the content being provided. Ab… |
| 1.3.6.1.4.1.9.9.598 | ciscoLwappAAAMIB | 3 | 73 | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC), that terminate the Light Weigh… |
| 1.3.6.1.4.1.9.9.599 | ciscoLwappDot11ClientMIB | 4 | 49 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.600 | ciscoGslbHealthMonMIB | 3 | 90 | The MIB defines objects related to global keepalive properties in GSLB devices. It contains the tables for keep alive configurat… |
| 1.3.6.1.4.1.9.9.601 | ciscoResilientEthernetProtocolMIB | 3 | 77 | This MIB module defines objects required for managing Resilient Ethernet Protocol (REP). Resilient Ethernet Protocol (REP) is a C… |
| 1.3.6.1.4.1.9.9.602 | ciscoPacketCaptureMIB | 3 | 103 | The MIB module for the management of packet capture feature. |
| 1.3.6.1.4.1.9.9.603 | ciscoThreatMitigationServiceMIB | 3 | 68 | This MIB provides management information about the Threat Mitigation Service(TMS) entity named 'Consumer'. TMS is part of Cisco's… |
| 1.3.6.1.4.1.9.9.604 | cdot1CfmMIB | 3 | 166 | Connectivity Fault Management module for managing IEEE 802.1ag |
| 1.3.6.1.4.1.9.9.606 | ciscoLwappMeshLinkTestMIB | 3 | 46 | ciscoLwappMeshLinkTestMIB MODULE-IDENTITY LAST-UPDATED "200702050000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Sy… |
| 1.3.6.1.4.1.9.9.607 | ciscoDot11HtPhyMIB | 3 | 71 | This MIB is intended to be implemented on Cisco's WLAN devices that provide the wired uplink to wireless clients through the high… |
| 1.3.6.1.4.1.9.9.610 | ciscoLwappRogueMIB | 3 | 78 | This MIB is intended to be implemented on all those devices operating as Central Controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.611 | ciscoLwappDot11ClientCCXTextualConventions | 0 | 0 | This module defines the textual conventions used throughout the Cisco enterprise MIBs designed for implementation on Central Cont… |
| 1.3.6.1.4.1.9.9.612 | ciscoLwappDot11MIB | 3 | 17 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.613 | ciscoEvcMIB | 3 | 156 | Metro Ethernet services can support a wide range of applications and subscriber needs easily, efficiently and cost-effectively. … |
| 1.3.6.1.4.1.9.9.614 | ciscoLwappDot11LdapMIB | 3 | 33 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.615 | ciscoLwappRrmMIB | 3 | 28 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.616 | ciscoLwappMeshMIB | 3 | 121 | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight… |
| 1.3.6.1.4.1.9.9.617 | ciscoLwappMeshStatsMIB | 4 | 98 | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight… |
| 1.3.6.1.4.1.9.9.618 | ciscoLwappSysMIB | 3 | 163 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.619 | ciscoLwappLocalAuthMIB | 3 | 53 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.621 | ciscoH324DialControlMIB | 2 | 34 | This MIB module enhances the IETF Dial Control MIB (RFC2128) by providing H.324 call information over a telephony network. ITU-T R… |
| 1.3.6.1.4.1.9.9.622 | ciscoLwappDot11ClientTsMIB | 3 | 34 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Acc… |
| 1.3.6.1.4.1.9.9.623 | ciscoLwappCdpMIB | 3 | 51 | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight… |
| 1.3.6.1.4.1.9.9.624 | ciscoIpSlaTCMIB | 0 | 0 | This MIB contains textual conventions used by CISCO IPSLA MIBs. Acronyms: FEC: Forward Equivalence Class LPD: Label Path Discovery L… |
| 1.3.6.1.4.1.9.9.626 | ciscoDot11HtMacMIB | 3 | 40 | This MIB is intended to be implemented on Cisco's WLAN devices that provide the wired uplink to wireless clients through the high… |
| 1.3.6.1.4.1.9.9.627 | ciscoDot11RadarMIB | 3 | 25 | This MIB module is for IEEE 802.11a/h Root device, i.e. Access Point (AP) or Root Bridge. This MIB allows dynamic frequency selec… |
| 1.3.6.1.4.1.9.9.628 | ciscoServiceControlSubscribersMIB | 3 | 37 | This MIB provides global and specific information on subscribers managed by a service control entity, which is a network element … |
| 1.3.6.1.4.1.9.9.630 | ciscoTelnetServerMIB | 3 | 34 | MIB module for displaying and configuring Telnet related features in a device. Telnet is a program to log into another computer o… |
| 1.3.6.1.4.1.9.9.631 | ciscoServiceControlLinkMIB | 3 | 21 | This MIB module provides information about the status and configuration of links used by service control entities. The link on a … |
| 1.3.6.1.4.1.9.9.632 | ciscoSmeMIB | 3 | 54 | MIB module to manage Storage Media Encryption (SME) service. SME is an encryption service provided by an encryption node residing… |
| 1.3.6.1.4.1.9.9.633 | ciscoIpSlaAutoMIB | 3 | 57 | This module defines the MIB for IP SLA Automation. IP SLA Automation consists of the following: 1. Use of grouping - Group is an … |
| 1.3.6.1.4.1.9.9.634 | ciscoServiceControlTpStatsMIB | 3 | 39 | This MIB provides information and statistics on the traffic processor(s) of a service control entity, which is a network element … |
| 1.3.6.1.4.1.9.9.635 | ciscoIpSlaJitterMIB | 3 | 57 | This MIB module defines templates for IP SLA operations of UDP Jitter and ICMP Jitter. The UDP Jitter operation is designed to me… |
| 1.3.6.1.4.1.9.9.636 | ciscoIpSlaEchoMIB | 3 | 71 | This MIB module defines the templates for IP SLA operations of ICMP echo, UDP echo and TCP connect. The ICMP echo operation measu… |
| 1.3.6.1.4.1.9.9.637 | ciscoServiceControlRdrMIB | 3 | 56 | This MIB module defines objects describing statistics and configuration relating to the Raw Data Record Formatter running on a se… |
| 1.3.6.1.4.1.9.9.638 | ciscoAgwMIB | 3 | 324 | This module manages Cisco's WiMAX ASN Gateway (ASN-GW). A WiMAX network supports wireless data communication through WiMAX radio … |
| 1.3.6.1.4.1.9.9.639 | ciscoOtnIfMIB | 3 | 137 | This MIB module defines the managed objects for physical layer characteristics of DWDM optical channel interfaces and performanc… |
| 1.3.6.1.4.1.9.9.640 | ciscoImageLicenseMgmtMIB | 3 | 31 | The MIB module for managing the running image level of a Cisco device. Cisco's licensing mechanism provides flexibility to run a … |
| 1.3.6.1.4.1.9.9.642 | ciscoBridgeDomainMIB | 3 | 24 | A bridge domain is one of the means by which it is possible to define a broadcast domain on a bridging device. It is an alternati… |
| 1.3.6.1.4.1.9.9.643 | ciscoTelepresenceMIB | 3 | 119 | The MIB module defines the managed objects for a Telepresence system. Telepresence refers to a set of technologies which allow a p… |
| 1.3.6.1.4.1.9.9.644 | ciscoTelepresenceCallMIB | 3 | 178 | The MIB module defines the managed objects for Telepresence calls. Telepresence refers to a set of technologies which allow a pers… |
| 1.3.6.1.4.1.9.9.645 | ciscoEtherExtMIB | 3 | 18 | The MIB module to describe generic objects for ethernet-like network interfaces. This MIB provides ethernet-like network interfac… |
| 1.3.6.1.4.1.9.9.646 | ciscoAonStatusMIB | 3 | 80 | This MIB module defines managed objects that facilitate the management of AON node. The information available through this MIB in… |
| 1.3.6.1.4.1.9.9.647 | ciscoGgsnExtMIB | 3 | 212 | This MIB module extends the CISCO-GGSN-MIB. This MIB module manages the Gateway GPRS Support Node (GGSN) devices. A GGSN device pr… |
| 1.3.6.1.4.1.9.9.648 | ciscoVirtualInterfaceMIB | 2 | 32 | The MIB module for creation and deletion of Virtual Interfaces and Virtual Interface Groups. In addition to this MIB, interface … |
| 1.3.6.1.4.1.9.9.650 | ciscoL4L7moduleRedundancyMIB | 3 | 71 | The L4-7 SLB devices are used for scaling websites, building web enabled applications, and migrating to web services. The followin… |
| 1.3.6.1.4.1.9.9.651 | ciscoCommonRolesExtMIB | 3 | 37 | A MIB Module for managing the roles that are common between access methods like Command Line Interface (CLI), SNMP and XML interf… |
| 1.3.6.1.4.1.9.9.652 | ciscoSwitchStatsMIB | 3 | 106 | The MIB module provides management information for configuration and monitoring of traffic statistics on Cisco's switching device… |
| 1.3.6.1.4.1.9.9.653 | ciscoAdmissionPolicyMIB | 3 | 36 | This MIB module defines managed objects that facilitate the management of policies upon host(s) admission to a network. The inform… |
| 1.3.6.1.4.1.9.9.654 | ciscoMabMIB | 3 | 20 | MIB module for monitoring and configuring MAC Authentication Bypass (MAB) feature in the system. MAC Auth Bypass feature provides… |
| 1.3.6.1.4.1.9.9.655 | ciscoDigitalMediaSystemsMIB | 3 | 195 | Acronyms and Definitions The following acronyms and terms are used in this document: DMS: Digital Media Systems DAM: Digital As… |
| 1.3.6.1.4.1.9.9.656 | ciscoAuthFrameworkMIB | 3 | 117 | MIB module for Authentication Framework in the system. Authentication Framework provides generic configurations for authenticatio… |
| 1.3.6.1.4.1.9.9.657 | ciscoSbcCallStatsMIB | 3 | 201 | The main purpose of this MIB is to define the statistics information for Session Border Controller application. The statistics ar… |
| 1.3.6.1.4.1.9.9.658 | ciscoSessBorderCtrlrEventMIB | 3 | 208 | The main purpose of this MIB is to define the SNMP notifications and alarms generated by Session Border Controller application an… |
| 1.3.6.1.4.1.9.9.660 | ciscoNportVirtualizationMIB | 3 | 19 | The MIB module for the management of N_port Virtualization or NPV within the framework of Cisco's N_port virtualization (NPV) Arc… |
| 1.3.6.1.4.1.9.9.661 | ciscoWan3gMIB | 3 | 378 | This MIB module provides network management support for Cisco cellular 3G WAN products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS … |
| 1.3.6.1.4.1.9.9.662 | ciscoCbpTcMIB | 0 | 0 | This MIB module defines textual conventions used by the CISCO-CBP-BASE-CFG-MIB, CISCO-CBP-BASE-MON-MIB, and any MIB modules exten… |
| 1.3.6.1.4.1.9.9.663 | ciscoSwitchHardwareCapacityMIB | 3 | 141 | This MIB module defines the managed objects for hardware capacity of Cisco switching devices. The hardware capacity information c… |
| 1.3.6.1.4.1.9.9.664 | ciscoMmodalContactAppsMIB | 3 | 359 | The Cisco Unified Multi-Modal Contact Applications (MMCA) platform is a highly scalable, modular, extensible, open and secure pl… |
| 1.3.6.1.4.1.9.9.667 | ciscoServiceControllerMIB | 2 | 31 | This MIB module defines objects describing traffic controllers used by a service control entity. A service control entity is a ne… |
| 1.3.6.1.4.1.9.9.668 | ciscoP2PIfMIB | 3 | 16 | The Point to Point Interface MIB module. This MIB manages the generic objects for Serial link or SONET/SDH like point to point ne… |
| 1.3.6.1.4.1.9.9.669 | ciscoCdmaPdsnExtMIB | 3 | 178 | This MIB is an extension to the CISCO-CDMA-PDSN-MIB. A CDMA network supports wireless data communication through 3G CDMA radio acc… |
| 1.3.6.1.4.1.9.9.670 | ciscoReportIntervalTcMIB | 0 | 0 | CISCO-REPORT-INTERVAL-TC-MIB |
| ... | ||||