The return value for the imaGrpChannelFailNotify trap.
startupFe
cfgAbort
configuartion parameters
cfgAbortFe
configuration parameters
insuffLinks
are active or less than the min number
of Rx links are active
insuffLinksFe
of Rx links or min number of Tx links
are active
blockedNe
blockedFe
timingSynch
occurred (CTC and CTC modes are not the same
at both ends of the IMA virtual links.
Parsed from file ac120.my.V07.00.C00.mib.txt
Company: None
Module: ACMIB
The return value for the imaGrpChannelFailNotify trap.
startupFe(1) Far-end is in the state of start-up
cfgAbort(2) this state is entered when the far-end tries to
use unacceptable configuration parameters including
invalid frame length and incompatable symmetry
cfgAbortFe(3) Far-end reported unacceptable configuration
parameters including invalid frame length and
incompatable symmetry
insuffLinks(4) Near-end reported less than the min number of
Tx links are active or less than the min number
of Rx links are active
insuffLinksFe(5) Far-end reported less than the min number of
Rx links are active or less than thenmin number
of Tx links are active
blockedNe(6) Near-end is administratively out-of-service
blockedFe(7) Far-end is administratively out-of-service
timingSynch(8) A possible configuration mismatch has
occurred (CTC and CTC modes are not the same
at both ends of the IMA virtual links.
Parsed from file ACMIB.mib
Module: ACMIB
Vendor: Lucent Technologies
Module: ACMIB
[Automatically extracted from oidview.com]
imaGrpChannelStatus OBJECT-TYPE SYNTAX INTEGER { startupFe(1), cfgAbort(2), cfgAbortFe(3), insuffLinks(4), insuffLinksFe(5), blockedNe(6), blockedFe(7), timingSynch(8) } MAX-ACCESS read-only STATUS current DESCRIPTION " The return value for the imaGrpChannelFailNotify trap. startupFe cfgAbort configuartion parameters cfgAbortFe configuration parameters insuffLinks are active or less than the min number of Rx links are active insuffLinksFe of Rx links or min number of Tx links are active blockedNe blockedFe timingSynch occurred (CTC and CTC modes are not the same at both ends of the IMA virtual links." ::= { returnCode 18 }
imaGrpChannelStatus OBJECT-TYPE SYNTAX INTEGER { startupFe(1), cfgAbort(2), cfgAbortFe(3), insuffLinks(4), insuffLinksFe(5), blockedNe(6), blockedFe(7), timingSynch(8) } MAX-ACCESS read-only STATUS current DESCRIPTION " The return value for the imaGrpChannelFailNotify trap. startupFe(1) Far-end is in the state of start-up cfgAbort(2) this state is entered when the far-end tries to use unacceptable configuration parameters including invalid frame length and incompatable symmetry cfgAbortFe(3) Far-end reported unacceptable configuration parameters including invalid frame length and incompatable symmetry insuffLinks(4) Near-end reported less than the min number of Tx links are active or less than the min number of Rx links are active insuffLinksFe(5) Far-end reported less than the min number of Rx links are active or less than thenmin number of Tx links are active blockedNe(6) Near-end is administratively out-of-service blockedFe(7) Far-end is administratively out-of-service timingSynch(8) A possible configuration mismatch has occurred (CTC and CTC modes are not the same at both ends of the IMA virtual links." ::= { returnCode 18 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1751.2.18.15.18.0 | imaGrpChannelStatus | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1751.2.18.15.1 | pvcFailureReasonCode | 1 | 1 | An identified reason why an ATM PVC connection request failed. |
| 1.3.6.1.4.1.1751.2.18.15.2 | interfaceIndex | 1 | 1 | Interface index used for identifcation in traps. Number value is interpreted as an interface of the form, SSPPCCC, where SS is th… |
| 1.3.6.1.4.1.1751.2.18.15.3 | interfaceType | 1 | 1 | Interface type used for identification in traps. A specific interface is associated with each number. |
| 1.3.6.1.4.1.1751.2.18.15.4 | interfaceFailureReasonCode | 1 | 1 | Identification of cause for failure in changing the status of an interface. interfaceInService: Most, if not all, modifications r… |
| 1.3.6.1.4.1.1751.2.18.15.5 | powerSupplyReasonCode | 1 | 1 | Identification for change in status of a power supply. |
| 1.3.6.1.4.1.1751.2.18.15.6 | portId | 1 | 1 | Port ID used for identification in traps. Number value is interpreted as a port of the form, SSPP, where SS is the card slot and… |
| 1.3.6.1.4.1.1751.2.18.15.7 | lineStatus | 1 | 1 | Bit map of the status of a line connected to a port. |
| 1.3.6.1.4.1.1751.2.18.15.8 | firmwareDownloadReasonCode | 1 | 1 | The suspected reasons of why a firmware download would fail. |
| 1.3.6.1.4.1.1751.2.18.15.9 | remoteRebootReasonCode | 1 | 1 | The result of a remote reboot request. |
| 1.3.6.1.4.1.1751.2.18.15.10 | saveConfigurationReasonCode | 1 | 1 | The result of a save configuration request. |
| 1.3.6.1.4.1.1751.2.18.15.11 | versionConfigurationReasonCode | 1 | 1 | Indicated status and results of version changing |
| 1.3.6.1.4.1.1751.2.18.15.12 | percentComplete | 1 | 1 | Used for trap fileTransferStatusNotify and value equals the percent of the upgrade, downgrade, or ftp download completed. |
| 1.3.6.1.4.1.1751.2.18.15.13 | ipTypeReasonCode | 1 | 1 | Indicator of which ip address had the problem. |
| 1.3.6.1.4.1.1751.2.18.15.14 | timingReasonCode | 1 | 1 | Indicator of type of relationship violated. |
| 1.3.6.1.4.1.1751.2.18.15.15 | alarmCardReasonCode | 1 | 1 | Configuration status of the alarm inputs and outputs. |
| 1.3.6.1.4.1.1751.2.18.15.16 | removeConfigFiles | 1 | 1 | Used to indicate the status of a remove configuration files request. |
| 1.3.6.1.4.1.1751.2.18.15.17 | spvcConfigFailureCode | 1 | 1 | Identification of cause for failure while configuring/modifying SPVC parameters. noSpvcConfigured : There endpoint has not been co… |
| 1.3.6.1.4.1.1751.2.18.15.19 | atmImaIntfStatus | 1 | 1 | The return value for the atmImaIntfFailNotify trap. lif (Loss of IMA Frame) lods (Link Out of Delay Synchronization) txMisConnect the… |
| 1.3.6.1.4.1.1751.2.18.15.20 | deviceId | 1 | 1 | device ID is used as the number of external devices. Each device can be an external input device or control output device. |
| 1.3.6.1.4.1.1751.2.18.15.21 | oamTestFailureReasonCode | 1 | 1 | An identified reason why an OAM Loopback Test request has failed. |
| 1.3.6.1.4.1.1751.2.18.15.22 | pnniCode | 1 | 1 | An identified reason for Miscellaneous Reasons in PNNI Configuration. |
| 1.3.6.1.4.1.1751.2.18.15.23 | swtchNodeIndx | 1 | 1 | Switch Node Index for PNNI. |
| 1.3.6.1.4.1.1751.2.18.15.24 | oc3APSPairPortIndex | 1 | 1 | APS Pair Port index - SSPP |
| 1.3.6.1.4.1.1751.2.18.15.25 | oc3APSReasonCode | 1 | 1 | Enumerated values of the outcome of previous apsPair UserCommand or alarms on the line |
| 1.3.6.1.4.1.1751.2.18.15.26 | oc3APSK1K2Rx | 1 | 1 | Rx K1/K2 followed by hex value of K1, K2 |
| 1.3.6.1.4.1.1751.2.18.15.27 | oc3APSK1K2Tx | 1 | 1 | Tx K1/K2 followed by hex value of K1, K2 |
| 1.3.6.1.4.1.1751.2.18.15.28 | oc3APSSelectorState | 1 | 1 | W: active/standby P: standby/active |
| 1.3.6.1.4.1.1751.2.18.15.29 | oc3APSWorkingLineSignalStatus | 1 | 1 | Line Status of the working port sent in a trap |
| 1.3.6.1.4.1.1751.2.18.15.30 | oc3APSProtectionLineSignalStatus | 1 | 1 | Line Status of the protection port sent in a trap. |
| 1.3.6.1.4.1.1751.2.18.15.31 | arpStatus | 1 | 1 | Success: Arp Data is Available. Failure: Reply from RS Card timed-out. |
| 1.3.6.1.4.1.1751.2.18.15.32 | routingStatus | 1 | 1 | Success: Routing Data is Available. Failure: Reply from RS Card timed-out. |
| 1.3.6.1.4.1.1751.2.18.15.33 | vpnTrapStatus | 1 | 1 | Return codes for route server VPN level operations. |
| 1.3.6.1.4.1.1751.2.18.15.34 | ipIntfStatus | 1 | 1 | Return codes for route server IP interface operations. |
| 1.3.6.1.4.1.1751.2.18.15.35 | subChanStatus | 1 | 1 | Return codes for route server sub channel connections operations. |
| 1.3.6.1.4.1.1751.2.18.15.36 | routeSrvStatus | 1 | 1 | Return codes for basic route server task operations not related to any specific VPN or IP/Connection operation. |
| 1.3.6.1.4.1.1751.2.18.15.37 | apsFailureReasonCode | 1 | 1 | aps failure reason |
| 1.3.6.1.4.1.1751.2.18.15.38 | statRtStatus | 1 | 1 | Return codes for route server static route condititions. |
| 1.3.6.1.4.1.1751.2.18.15.39 | portFailureReasonCode | 1 | 1 | Identification of cause for failure in changing the parameters of a port |
| 1.3.6.1.4.1.1751.2.18.15.40 | dlciNumber | 1 | 1 | The number of the dlci being used. |
| 1.3.6.1.4.1.1751.2.18.15.41 | ipAddrNumber | 1 | 1 | The IP address of the host/network to be echoed |
| 1.3.6.1.4.1.1751.2.18.15.42 | pingStatusReasonCode | 1 | 1 | The response value - Alive/Not Alive |
| 1.3.6.1.4.1.1751.2.18.15.43 | primarySoftwareVersion | 1 | 1 | Software version running on primary cpu. |
| 1.3.6.1.4.1.1751.2.18.15.44 | backupSoftwareVersion | 1 | 1 | Software version running on backup cpu. |
| 1.3.6.1.4.1.1751.2.18.15.45 | oamActDeactResultCode | 1 | 1 | Various result codes for the operator's command for OAM Activation-Deactivation. |
| 1.3.6.1.4.1.1751.2.18.15.46 | tasCmprsAnnceReasonCode | 1 | 1 | The result of a compress announcement request. |
| 1.3.6.1.4.1.1751.2.18.15.47 | tasTstLineReasonCode | 1 | 1 | The result of a test line request. |
| 1.3.6.1.4.1.1751.2.18.15.48 | gr303PPSReasonCode | 1 | 1 | gr303 PPS reason code |
| 1.3.6.1.4.1.1751.2.18.15.49 | gr303PPSSource | 1 | 1 | gr303 PPS source |
| 1.3.6.1.4.1.1751.2.18.15.50 | tasMemReasonCode | 1 | 1 | The result of a memory init request. |
| 1.3.6.1.4.1.1751.2.18.15.51 | tasTrapTstId | 1 | 1 | Announcement ID for trap. |
| 1.3.6.1.4.1.1751.2.18.15.52 | tasTrapAnnceId | 1 | 1 | test id for trap. |
| 1.3.6.1.4.1.1751.2.18.15.53 | atmVpi | 1 | 1 | Vpi is used in identification of Traps |
| 1.3.6.1.4.1.1751.2.18.15.54 | atmVci | 1 | 1 | Vci is used in identification of Traps |
| 1.3.6.1.4.1.1751.2.18.15.55 | iptResultCode | 1 | 1 | Various result codes for the operator's command forsetting/deleting interface protection group. |
| 1.3.6.1.4.1.1751.2.18.15.56 | pgtResultCode | 1 | 1 | Various result codes for the operator's command for interface protection . |
| 1.3.6.1.4.1.1751.2.18.15.57 | tasmControlBlockAllocFailReasonCode | 1 | 1 | The result of a tasm control block memory allocation request. |
| 1.3.6.1.4.1.1751.2.18.15.58 | tasmCacheMemAllocFailReasonCode | 1 | 1 | The result of a tasm control block memory allocation request. |
| 1.3.6.1.4.1.1751.2.18.15.59 | atmTrunkingConfigFailureCode | 1 | 1 | An identified reason for failure while configuring/modifying ATM Trunking parameters: localIWFAlreadyConfigured(1) : Local IWF has… |
| 1.3.6.1.4.1.1751.2.18.15.60 | sapphireIntfAddressFailReasonCode | 1 | 1 | The result of assigning the Sapphire Interface address when PSAX is Sapphire client. address-ok(1), Address assignment suc… |
| 1.3.6.1.4.1.1751.2.18.15.61 | chassisOverTempAlarmReasonCode | 1 | 1 | Indicator of presence of chassis over temperature alarm. |